DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 4
Technical content
5000 WATT PEAK POWER TRANSIENT VOLTAGE SUPPRESSORS
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATINGS SYMBOL VALUE UNITS Peak Power Dissipation at TA=25 C, TP=1ms(NOTE 1) PPK Minimum 5000 Watts
FEATURES
- 5000 Watts Surge Capability at 1ms 1.0ps from 0 volt to BV min. * Typical IR less than 1 A above 10V * Fast response time: Typically less than * Low zener impedance * Excellent clamping capability * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Axial leads, solderable per MIL-STD-202, method 208 guranteed * Polarity: Color band denotes cathode end * Mounting position: Any 5KP SERIES VOLTAGE RANGE R-6 Dimensions in inches and (millimeters) 1.0(25.4) MIN. 1.0(25.4) MIN. .360(9.1) .360(9.1) .340(8.6) .340(8.6) .052(1.3) .048(1.2) DIA. DIA. 5.0 to 440 Volts
5000 Watts Peak Power
Power Dissipation on infinite heatsink at TL=75 C PD 8.0 Watt Peak Forward Surge Current at 8.3ms Single Half Sine-Wave Maximum Instantenous Forward Voltage at 100A for superimposed on rated load (JEDEC method) (NOTE 3) Unidirectional only Operating and Storage Temperature Range TJ, TSTG -55 to +150 C IFSM 500 Amps VF 3.5/5.0 Volts NOTES: 1. Non-repetitive current pulse per Fig. 3 and derated above TA=25 C per Fig. 2. 2. 8.3ms single half sine-wave, duty cycle = 4 pulses per minute maximum. 3. VF<3.5V for devices of VBR<200V and VF<5.0V for devices of VBR>201V. DEVICES FOR BIPOLAR APPLICATIONS 1. For Bidirectional use C or CA Suffix for types 5KP5.0 thru 5KP440. 2. Electrical characteristics apply in both directions. 364
RATING AND CHARACTERISTIC CURVES (5KP SERIES) PPPM, PEAK PULSE POWER, (KW)IPPM, PEAK PULSE CURRENT, (%) Pm(AV), STEADY STATE POWER DISSIPATION, (WATTS) FIG.1-PEAK PULSE POWER DERATING CURVE 0.1ms 1.0ms 10ms 100ms 1.0ms 10ms 0.1 1.0 100 td, PULSE WIDTH, sec. Non-Repetitive Pulse Waveform Shown in Fig. 3 TA=25 C FIG.2-PULSE DERATING CURVE PEAK PULSE POWER(PPP) OR CURRENT(IPP) DERATING IN PERCENTAGE, (%) TA, AMBIENT TEMPERATURE ( C) TL, LEAD TEMPERATURE ( C) 0 25 50 75 100 125 150 175 100 FIG.3-PULSE WAVE FORM 0 1.0 2.0 3.0 4.0 t, TIME, ms 100 150 td Tf=10 s Peak Value IPPM Half Value-IPPM TA=25 C Pulse Width (td) is defined as the point where the Peak Current Deacys to 50% of Ipp 0 25 50 75 100 125 150 175 200 FIG.5-STEADY STATE POWER DERATING CURVE FIG.4-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT, UNIDIRECTIONAL 1 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz 100 300 500 IFSM, PEAK FORWARD SURGE CURRENT, (AMPERES) TJ=TJmax 8.3ms Single Half Sine-wave JEDEC Method 10/1000 sec Waveform as Defined by R.E.A. 365
5000 Watt Axial Lead TVS
VR (V) Min (V) Max (V) IT (mA) IR (µA) Ipp (A) Vc (V) 366 Maximum Clamping Voltage @ Ipp Breakdown Voltage VBR @ IT Maximum Reverse Leakage @ VR Reverse Standoff Voltage Part Number (Uni) Part Number (Bi) Maximum Peak Pulse Current
VR (V) Min (V) Max (V) IT (mA) IR (µA) Ipp (A) Vc (V) 367 Maximum Clamping Voltage @ Ipp Part Number (Uni) Part Number (Bi) Reverse Standoff Voltage Breakdown Voltage VBR @ IT Maximum Reverse Leakage @ VR Maximum Peak Pulse Current