SMD0503 ETC2

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Item: CRYSTAL Type: SMD0503 SSPPEECCIIFFIICCAATTIIOONN SSHHOOUULLDDEERR Optional

SSMMDD00550033 CCRRYYSSTTAALL SHOULDER INDÚSTRIA ELETRÔNICA LTDA Page 2 of 5 Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br SSSHHHOOOUUULLLDDDEEERRR EElleeccttrriiccaall SSppeecciiffiiccaattiioonn Parameter Value Nominal Frequency 10.00 to 80.000 MHz Frequency Tolerance (at 25°C) + 30 PPM (Maximum) Frequency Stability + 30 PPM (Maximum) Oscilation Mode Fundamental Equivalent Series resistance 50 Ω Drive Level 1.0 mW (Maximum) Operating Temperature Range -20 to + 70ºC Standard (or Optional) Storage Temperature -40 to + 85ºC Load Capacitance 10 pF to Series Shunt Capacitance < 7 PF Aging (at 25°C) + 3 ppM per year Insulation Resistance > 500 MΩ at DC 100V SSccooppee This specification shall cover the characteristics of SMD 5x3.2 crystal. Ultra small package Wide Frequency Range MMeecchhaanniiccaall DDiimmeennssiioonnss ((AAllll iinn mmmm)) SSMMDD00550033

SSMMDD00550033 CCRRYYSSTTAALL SHOULDER INDÚSTRIA ELETRÔNICA LTDA Page 3 of 5 Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br SSSHHHOOOUUULLLDDDEEERRR SSoollddeerriinngg MMeecchhaanniiccaall SSppeecciiffiiccaattiioonn Conditions Results 1. Vibration test Frequency 10 ~ 55Hz Amplitude 0.762mm Sweep 1.0 minute Duration 2 hours Frequency and wave form of tested products must remain within specifications. 2. Drop test Method of drop Natural drop Dropping floor Hard wood board Height 30cm Number of drops 3 times Frequency and wave form of tested products must remain within specifications. EEnnvviirroonnmmeennttaall SSppeecciiffiiccaattiioonn Conditions Results 1. Temperature test 1) at -55°C, 30 minutes 2) at +25°C, 10~15 minutes 3) at +85°C, 30 minutes Steps of cycle 4) at +25°C, 10~15 minutes Temperature cycling test Number of cycles 3 times Frequency and wave form of tested products must remain within specifications. 2. Aging test Temperature +85°C ±20°C Length of test 96 hours Deviation of frequency must be less than ±3ppM. 3. Salt spray test Temperature +35°C ±2°C Length of test 48 hours NaCI % 5% There should be no stain on surface of products. 4. Humidity test Temperature +40°C ±2°C Relative humidity 90 ~ 95% Length of test 96 hours a) Insulation resistance must be 500 MΩ/100 Vac minimum. b) Resistance and wave form must remain within specifications.

SSMMDD00550033 CCRRYYSSTTAALL SHOULDER INDÚSTRIA ELETRÔNICA LTDA Page 4 of 5 Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br SSSHHHOOOUUULLLDDDEEERRR SSMMDD00550033 CCRRYYSSTTAALL PPaarrtt NNuummbbeerriinngg SSyysstteemm ((EExxaammppllee)) TTaappee SSppeecciiffiiccaattiioonnss ((AAllll iinn mmmm)) Reeling Quantity - 1000pcs / reel Carrier Tape Dimensions W F P0 P1 D0 D1 t1 t2 A B 16+ 0.3 5.5+ 0.05 4.0+ 0.1 9.0+ 0.1 ∅1.5+ 0.1 ∅1.6 + 0.25 0.3+ 0.03 1.7+ 0.1 4.2+ 0.1 0.1

SSMMDD00550033 CCRRYYSSTTAALL SHOULDER INDÚSTRIA ELETRÔNICA LTDA Page 5 of 5 Rua Vereador Antonio Zamarioni, 105 (Portal de Extrema) CEP 37640-000 Extrema / MG www.hdshoulder.com.br SSSHHHOOOUUULLLDDDEEERRR SMD0503 11.0592 F 20 30 30 A T Type Nominal Frequency (in MHz) Vibration Mode Load Capacitance Frequency Tolerance Frequency Stability Operating Temperature Range Option (can be blank) A -20°C to 70°C B -10°C to 60°C C 0°C to 50°C D -30°C to 80°C SMD0503 49S-SMD 49S2-SMD SMD0804 SMD0705 SMD0603 SMD0402 Enter the nominal frequency (3 digits after dot) or up to last significant digit (different than zero) F = Fund S = Series Or enter load capacitance: 10 to 33 for parallel Indicate the tolerance value in ± PPM Indicate the stability over temperature range value in ± PPM E -40°C to 85°C S= Standard X= Additional Specifications T= Tape and Reel