48AV-2CVA-R

48AV MSYSTEM

Document overview

• PDF pages: 5

Technical content

Page 1

Bargraph Indicators 48 Series

BARGRAPH INDICATING ALARM

C: 1 – 5 mA DC (Input resistance 39 Ω) D: 0 – 20 mA DC (Input resistance 10 Ω) E: 0 – 16 mA DC (Input resistance 12 Ω) F: 0 – 10 mA DC (Input resistance 20 Ω)

MODEL: 48AV–[1][2][3][4]-[5]

ORDERING INFORMATION

• Code number: 48AV-[1][2][3][4]-[5] Specify a code from below for each [1] through [5]. (e.g. 48AV-4RVA-R)
• Special input range (For codes Z & 0)
• Scale (e.g. 0 – 100 %)
• Color pattern for multi-color indicator (e.g. pattern 2)

[1] ALARM OUTPUT

2: 2 points 4: 4 points

[2] BAR LED COLOR

R: Red Y: Amber G: Green C: Multi-color (red, amber and green)

[3] MOUNTING DIRECTION

V: Vertical H: Horizontal

[4] INPUT

Current A: 4 – 20 mA DC (Input resistance 10 Ω) B: 2 – 10 mA DC (Input resistance 20 Ω)

G: 0 – 1 mA DC (Input resistance 200 Ω) H: 10 – 50 mA DC (Input resistance 5.1 Ω) Z: Specify current (See INPUT SPECIFICATIONS) Voltage 3: 0 – 1 V DC (Input resistance 100 kΩ) 4: 0 – 10 V DC (Input resistance 330 kΩ) 5: 0 – 5 V DC (Input resistance 250 kΩ) 6: 1 – 5 V DC (Input resistance 250 kΩ) 0: Specify voltage (See INPUT SPECIFICATIONS)

[5] POWER INPUT

AC Power K: 85 – 132 V AC (Operational voltage range 85 – 132 V, 47 – 63 Hz) L: 170 – 264 V AC (Operational voltage range 170 – 264 V, 47 – 63 Hz) DC Power R: 24 V DC (Operational voltage range 24 V ±15 %, ripple 10 %p-p max.)

GENERAL SPECIFICATIONS

Construction: Panel flush mounting Connection: M3 screw terminals (torque 0.6 N·m) Screw terminal: Chromated brass Housing material: ABS resin Isolation: Input to output to power Zero adjustment: -5 to +5 % (front) Span adjustment: 95 to 105 % (front) Scale plate: Aluminium (white scale & characters on black base) Scale Characters including decimal points: Max. 4 characters Divisions: 22 – 54.9 Engineering unit: Max. 8 characters Setpoint adjustment 2 points: H: [L setpoint + 1 %] to 100 % L: 0 % to [H setpoint – 1 %] 4 points: HH: [H setpoint + 1 %] to 100 % H: [L setpoint + 1 %] to [HH setpoint – 1 %] L: [LL setpoint + 1 %] to [H setpoint – 1 %] LL: 0 % to [L setpoint – 1 %]

Alarm deadband (hysteresis): 1 % Bargraph: 101-segment LED, 100 mm (3.96”) long, 1.5 mm (.06”) wide

ES-9312 Rev.18 Page 1/5

Page 2

INPUT SPECIFICATIONS

■ DC Current: 0 – 50 mA DC; input resistor incorporated Minimum span: 1 mA 0 % input: 0 mA DC ■ DC Voltage: 0 – 10 V DC Minimum span: 1 V 0 % input: 0 V DC

OUTPUT SPECIFICATIONS

■ Alarm Output: Relay contact Rated load: 125 V AC @ 0.5 A (cos ø = 1) 30 V DC @ 2 A (resistive load) Maximum switching voltage: 250 V AC or 220 V DC Maximum switching power: 125 VA or 60 W Minimum load: 10 mV DC @ 10 μA Mechanical life: ≥ 108 cycles

Alarm Trip Operation Terminal No. in parentheses

• Output Code : 2

H Output

L Output

Input (%)

• Output Code : 4

HH Output

H Output

L Output

LL Output

Input (%)

Setp. Setp. Setp. Setp.

Trip Operation in Power Failure: Terminals 3 – 5, 9 – 10 turn ON

INSTALLATION

Power consumption

• AC: Approx. 5 VA (7 VA for multi-color LED)
• DC: Approx. 4 W (6 W for multi-color LED) Operating temperature: 0 to 45°C (32 to 113°F) Operating humidity: 40 to 80 % RH (non-condensing) Mounting: Panel flush mounting

Weight: 590 g (1.30 lbs)

PERFORMANCE in percentage of span

Accuracy: ±1 % ±1 digit Setting accuracy: ±1 % Response time: 0.5 sec. Insulation resistance: ≥ 10 MΩ with 500 V DC (input to output to power) Dielectric strength: 1500 V AC @ 1 minute (input to power or ground) 1000 V AC @ 1 minute (power to ground, output to input or power or ground)

ES-9312 Rev.18 Page 2/5

Page 3

STANDARD SCALE & UNIT EXAMPLES

■ DIVISIONS Number of divisions depends upon the scale range.

■ STANDARD SCALES & DIVISIONS (example)

Enginnering unit: %, °C, Nm3/h, m3/h, t/h, km3/h, kg/h, l/h, Pa, kPa, abs, ppm, pH, psi, kg/cm2G, N/m2, N/cm2, lb/h, J, kJ, Nl, m3, lbs, Ω, μΩ, 1°

Span of Scale Range = (Full Scale – Zero Scale) × 10n where n = integer (Determine ‘n’ so that the span of scale range is 1.1 or greater than 1.1, and smaller than 11.0.)

[Example 1] Scale range 0 to 100

Example 1

Example 2

Span of Scale Range = (100 – 0) × 10-1 = 10 Span of 10 falls into Pattern 5 according to the above table. Number of divisions

100

10

is calculated from the Span of Scale Range multiplied by the ratio (10 × 5).

90

The scale range 0 to 100 is provided with 50 divisions.

80

5

[Example 2] Scale range -10 to +10

70

Span of Scale Range = (10 – (-10)) × 10-1 = 2

60

Span of 2 falls into Pattern 3 according to the above table. Number of divisions is calculated from the Span of Scale Range multiplied by the ratio (2 × 20).

0

50

The scale range -10 to +10 is provided with 40 divisions.

40

30

5

20

10

10

0 Unit

Unit –

ES-9312 Rev.18 Page 3/5

Page 4

EXTERNAL VIEW

■ VERTICAL MOUNTING

Tag No. Label

50

SET: ENTER Button

40

HH Setpoint

SET 30

HH Setpoint Adj. & Trip Indicator HH

H Setpoint

20

H Setoint Adj. & Trip Indicator H

L Setpoint

10

SPAN Adj. S Display OFF

0

LL Setpoint

ZERO Adj. Z 10

L Setpoint Adj. & Trip Indicator L

Status Indicator

20

LL Setpoint Adj. & Trip Indicator LL

UP Button

30

Mode Selector M 40

DOWN Button

50 – Nm3/min

HH and LL Setpoint Adj. are deleted with model 48AV-2.

■ HORIZONTAL MOUNTING

Tag No. Label

\*Engineering units longer than 3 characters are indicated here. HH and LL Setpoint Adj. are deleted with model 48AV-2.

CONNECTION DIAGRAM

■ 48AV-2

+ 1 3 Hc

INPUT

INPUT

– 2 4 Ha HH OUTPUT

5 Hb

8 La

9 Lb LL OUTPUT

10 Lc

11 U(+) POWER V(–) 12

■Relay Protection

• DC Powered
• AC Powered

Inductive

Inductive

Load (Coil)

Load (Coil)

Diode, Varistor or

Varistor or

CR Circuit

CR Circuit

LOAD

LOAD

Multi-Color Indication

Pattern 1

Lo < Input < Hi Hi < Input Input < Lo Input < Lo Lo < Input < Hi Hi < Input

Pattern 2

■48AV-4

+ 1

– 2 4

5

6

7 La

8

9

10

11 U(+) POWER 12 V(–)

ES-9312 Rev.18 Page 4/5

Page 5

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

BEZEL

M3 (.12) SCREW

BEZEL

PANEL CUTOUT unit: mm

■ VERTICAL MOUNTING

Panel thickness: 1.6 – 5.5 mm

+1 L = (38 x n) –0 (n: number of units) L

Note 1. A bezel is required between units for high-density mounting. Note 2. Observe at the minimum of 5 cm above and below the units for heat dissipation.

■ HORIZONTAL MOUNTING

Panel thickness: 1.6 – 5.5 mm

+1

+1

L = 38 x (n–1) + 36.5

–0

(n: number of units)

Note 1. A bezel is required between units for high-density mounting.

ES-9312 Rev.18 Page 5/5