4652403 TURCK
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 4
Technical content
Features
■Threaded barrel, M18 x 1 ■Plastic, PA12‐GF30 ■DC 3-wire, 10…30 VDC ■NO contact, PNP output ■M12 x 1 male connector ■ATEX category II 3 D, Ex-zone 22 Wiring diagram Functional principle Inductive sensors detect metal objects contactless and wear-free. For this, they use a high-frequency electromagnetic AC field that interacts with the target. Inductive sensors generate this field via an RLC circuit with a ferrite coil.
TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: 763-553-7300 | Application Support: 1-800-544-7769 | Fax 763-553-0708 | www.turck.com 2|4 BI5-S18-AP6X-H1141/S58/3D | 11/07/2023 15-04 | technical changes reserved Technical data Approval acc. to ATEX test certificate TURCK Ex-03002H X Device marking É II 3 D Ex tc IIIC T95°C Dc Mechanical data Design Threaded barrel, M18 x 1 Dimensions 73 mm Housing material Plastic, PA12-GF30 Active area material Plastic, PA12-GF30 Max. tightening torque of housing nut 2 Nm Electrical connection Connector, M12 × 1 Environmental conditions Ambient temperature -25…+70 °C Vibration resistance 55 Hz (1 mm) Shock resistance 30 g (11 ms) Protection class IP67 MTTF 2283 years acc. to SN 29500 (Ed. 99) 40 Switching state LED, Yellow Included in delivery SC-M12/3GD
TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: 763-553-7300 | Application Support: 1-800-544-7769 | Fax 763-553-0708 | www.turck.com 3|4 BI5-S18-AP6X-H1141/S58/3D | 11/07/2023 15-04 | technical changes reserved Mounting instructions Mounting instructions/Description Distance D 2 x B Distance W 3 x Sn Distance T 3 x B Distance S 1.5 x B Distance G 6 x Sn Diameter active area B Ø 18 mm Accessories QM-18 6945102 Quick-mount bracket with dead-stop; material: Chrome-plated brass. Male thread M24 × 1.5. Note: The switching distance of the proximity switches may change when using quick-mount brackets. BST-18B 6947214 Mounting clamp for threaded barrel sensors, with dead-stop; material: PA6 MW-18 6945004 Mounting bracket for threaded barrel sensors; material: Stainless steel A2 1.4301 (AISI 304) BSS-18 6901320 Mounting clamp for smooth and threaded barrel sensors; material: Polypropylene
TURCK Inc. | 3000 Campus Drive Minneapolis, MN 55441-2656 | Phone: 763-553-7300 | Application Support: 1-800-544-7769 | Fax 763-553-0708 | www.turck.com 4|4 BI5-S18-AP6X-H1141/S58/3D | 11/07/2023 15-04 | technical changes reserved Instructions for use Intended use This device fulfills the directive 2014/34/EC and is suited for use in explosion hazardous areas according to EN60079-0:2012 and EN60079-31:2014.In order to ensure correct operation to the intended purpose it is required to observe the national regulations and directives. For use in explosion hazardous areas conform to classification II 3 D (Group II, Category 3 D, electrical equipment for dust atmospheres). Marking (see device or technical data sheet) É II 3 D Ex tc IIIC T95°C Dc acc. to EN60079-0:2012 und EN60079-31:2014 Local admissible ambient temperature -25…+70 °C Installation/Commissioning These devices may only be installed, connected and operated by trained and qualified staff. Qualified staff must have knowledge of protection classes, directives and regulations concerning electrical equipment designed for use in explosion hazardous areas.Please verify that the classification and the marking on the device comply with the actual application conditions. Installation and mounting instructions Avoid static charging of cables and plastic devices. Please only clean the device with a damp cloth. Do not install the device in a dust flow and avoid build-up of dust deposits on the device.If the devices and the cable could be subject to mechanical damage, they must be protected accordingly. They must also be shielded against strong electro-magnetic fields.The pin configuration and the electrical specifications can be taken from the device marking or the technical data sheet.In order to avoid contamination of the device, please remove possible blanking plugs of the cable glands or connectors only shortly before inserting the cable or opening the cable socket. Special conditions for safe operation Devices with terminal chamber (cable glands) have a weaker strain relief. Sufficient strain relief must be ensured or the cable must be stationary-mounted.For devices with M12 connectors please use the supplied safety clip SC- M12/3GD.Do not disconnect the plug-in connection or cable under voltage.The device must be protected against any kind of mechanical damage and degrading UV-radiation.Load voltage and operating voltage of this equipment must be supplied from power supplies with safe isolation (IEC 30 364/UL508), to ensure that the rated voltage of the equipment (24 VDC +10% = 26.4 VDC) is never exceeded by more than 40%. Service/Maintenance Repairs are not possible. The approval expires if the device is repaired or modified by a person other than the manufacturer. The most important data from the approval are listed.