444164 YAGEO

Document overview

  • PDF pages: 9

Technical content

Page 1

PDF page 1 diagram
PDF page 1 diagram

Page 2

PDF page 2 diagram

ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC

SCOPE

Both part numbers are identified by the series, size, tolerance, packing

This specification describes

type, temperature coefficient, taping reel and resistance value.

RC0805 series chip resistors with lead-free terminations made

NDD oorrddeerriinngg ccooddee

YYAAG

GEEO

O BBRRAAN

by thick film process.

GLOBAL PART NUMBER (PREFERRED)

RC0805 X R - XX XXXX L

APPLICATIONS

(1) (2) (3) (4) (5) (6)

z All general purpose application

(1) TOLERANCE

F = ±1%

FEATURES

J = ±5% (for Jumper ordering, use code of J)

z Halogen Free Epoxy

(2) PACKAGING TYPE

z RoHS compliant

R = Paper taping reel

  • Products with lead free terminations meet RoHS

(3) TEMPERATURE COEFFICIENT OF RESISTANCE

requirements

– = Base on spec

  • Pb-glass contained in electrodes, resistor element and glass are

(4) TAPING REEL

exempted by RoHS

07 = 7 inch dia. Reel

z Reducing environmentally

10 = 10 inch dia. Reel

hazardous wastes

13 = 13 inch dia. Reel

z High component and equipment

(5) RESISTANCE VALUE

reliability

There are 2~4 digits indicated the resistor value. Letter R/K/M is decimal point, no need

z Saving of PCB space

to mention the last zero after R/K/M, e.g.1K2, not 1K20.

z None forbidden-materials used

Detailed resistance rules show in table of “Resistance rule of global part number”.

in products/production

(6) DEFAULT CODE Letter L is system default code for order only (Note)

Resistance rule of global part number Resistance code rule

0R

XRXX (1 to 9.76 Ω)

XXRX (10 to 97.6 Ω) XXXR (100 to 976 Ω) XKXX (1 to 9.76 KΩ) XMXX

ORDERING EXAMPLE

The ordering code of a RC0805

Example

chip resistor, value 56 X with

0R = Jumper ±1% tolerance, supplied in 7-inch

tape reel is: RC0805FR-0756RL.

1R = 1 Ω 1R5 = 1.5 Ω

NOTE

9R76 = 9.76 Ω

  1. All our RSMD products meet RoHS

10R = 10 Ω

compliant and Halogen Free. "LFP" of

97R6 = 97.6 Ω

the internal 2D reel label mentions "Lead Free Process"

100R = 100 Ω

  1. On customized label, "LFP" or specific symbol can be printed

1K = 1,000 Ω 9K76 = 9760 Ω 1M = 1,000,000 Ω

(1 to 9.76 MΩ) 9M76= 9,760,000 Ω

Page 3

PDF page 3 diagram

PPH

HYYCCO

OM

MPP BBRRAAN

NDD oorrddeerriinngg ccooddeess

Both GLOBAL PART NUMBER (preferred) and 12NC (traditional) codes are acceptable to order Phycomp brand products.

GLOBAL PART NUMBER (PREFERRED)

For detailed information of GLOBAL PART NUMBER and ordering example, please refer to page 2.

12NC CODE

2322 / 2350 XXX XXXXX L

Last digit of 12NC Resistance decade (3)

(1) (2) (3) (4)

Last digit

PAPER / PE TAPE ON REEL (units) (2)

TYPE/ START TOL. RESISTANCE 0805 IN (1) (%) RANGE

5,000 10,000/not preferred

RC11 2322 ±5% 1 to 10 MΩ

730 61xxx

730 71xxx

RC12 2322 ±1% 1 to 10 MΩ

734 6xxxx

734 7xxxx

HRC11 2350 ±5% 11 to 22 MΩ 521 10xxx

-

0 Ω

Jumper 2322 -

730 91002

730 91003

0.01 to 0.0976 X

0

0.1 to 0.976 X

7

20,000 1 to 9.76 X

8

730 81xxx

10 to 97.6 X

734 8xxxx

100 to 976 X

1

  • 1 to 9.76 KX

2

730 92002

10 to 97.6 KX

3

(1) The resistors have a 12-digit ordering code starting with 2322 / 2350.

100 to 976 KX

4

(2) The subsequent 4 or 5 digits indicate the resistor tolerance and

1 to 9.76 MX

5

packaging.

10 to 97.6 MX

6

(3) The remaining 4 or 3 digits represent the resistance value with the last digit indicating the multiplier as shown in the table of “Last digit of 12NC”.

(4) Letter L is system default code for order only (Note)

ORDERING EXAMPLE

Example: 0.02 X = 0200 or 200 0.3 X = 3007 or 307 1 X = 1008 or 108 33 KX = 3303 or 333 10 MX = 1006 or 106

The ordering code of a RC12 resistor, value 56 X with ±1% tolerance, supplied in tape of 5,000 units per reel is: 232273465609L or RC0805FR-0756RL.

NOTE

  1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process" 2. On customized label, "LFP" or specific symbol can be printed

Page 4

PDF page 4 diagram

MARKING RC0805

E-24 series: 3 digits

03

First two digits for significant figure and 3rd digit for number of zeros

Fig. 1 Value=10 KΩ

Both E-24 and E-96 series: 4 digits

00

First three digits for significant figure and 4th digit for number of zeros

Fig. 2 Value=10 KΩ

For further marking information, please see special data sheet “Chip resistors marking”

CONSTRUCTION

OU

UTTLLIIN

NEESS

O

The resistor is constructed on top

PDF page 4 diagram

of a high-grade ceramic body. Internal metal electrodes are added on each end to make the contacts to the thick film resistive element. The composition of the resistive element is a noble metal imbedded into a glass and covered by a second glass to prevent environment influences. The resistor is laser trimmed to the rated resistance value. The resistor is covered with a protective epoxy coat, finally the two external terminations (matte tin on Ni- barrier) are added. See fig.3

DIMENSIONS

Table 1 TYPE

RC0805

L (mm)

2.00 ±0.10

W (mm)

1.25 ±0.10

H (mm)

0.50 ±0.10

I1 (mm)

0.35 ±0.20

I2 (mm)

0.35 ±0.20

Page 5

PDF page 5 diagram

ELECTRICAL CHARACTERISTICS Table 2

CHARACTERISTICS Operating Temperature Range Maximum Working Voltage Maximum Overload Voltage Dielectric Withstanding Voltage

5% (E24)

Resistance Range

1% (E24/E96)

FOOTPRINT AND SOLDERING PROFILES For recommended footprint and

RC0805 1/8 W

soldering profiles, please see the

–55 °C to +155 °C

special data sheet “Chip resistors 150 V mounting”. 300 V 300 V 1 Ω to 22 MΩ 1 Ω to 10 MΩ Zero Ohm Jumper < 0.05 Ω 1 Ω ≤ R ≤ 10 Ω

Temperature Coefficient

10 MΩ < R ≤ 22 MΩ 10 Ω < R ≤ 10 MΩ Rated Current

Jumper Criteria

Maximum Current

PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PRODUCT TYPE

PACKING STYLE

RC0805

Paper Taping Reel (R)

NOTE

±200 ppm/°C ±200 ppm/°C ±100 ppm/°C 2 A 5 A

REEL DIMENSION

QUANTITY PER REEL

7" (178 mm)

5,000 units

10" (254 mm)

10,000 units

13" (330 mm)

20,000 units

  1. For paper tape and reel specification/dimensions, please see the special data sheet “Chip resistors packing”

FUNCTIONAL DESCRIPTION

PDF page 5 diagram

PPO OW

WEERR RRAATTIIN

NGG

RC0805 rated power at 70°C is 1/8 W

RATED VOLTAGE

The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula:

V=√(P X R) or max. working voltage whichever is less

Where

V=Continuous rated DC or AC (rms) working voltage (V)

P=Rated power (W)

R=Resistance value (X)

Page 6

PDF page 6 diagram

TESTS AND REQUIREMENTS Table 4 Test condition, procedure and requirements

TEST

TEST METHOD

PROCEDURE

REQUIREMENTS

At +25/–55 °C and +25/+125 °C

IEC 60115-1 4.8

Temperature

Refer to table 2

Coefficient of Resistance

Formula:

(T.C.R.)

R2–R1 T.C.R= ------------------------- ×106 (ppm/°C) R1(t2–t1)

Where t1=+25 °C or specified room temperature t2=–55 °C or +125 °C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms

At 70±5 °C for 1,000 hours, RCWV applied for

IEC 60115-1 4.25.1

±(1.0%+0.05 Ω) for 1% tol.

Life/Endurance

1.5 hours on, 0.5 hour off, still air required

±(3.0%+0.05 Ω) for 5% tol. <100 mΩ for Jumper

1,000 hours at 155±5 °C, unpowered

IEC 60068-2-2

High Temperature Exposure/ Endurance at Upper Category Temperature

±(1.0%+0.05 Ω) for 1% tol. ±(2.0%+0.05 Ω) for 5% tol. <50 mΩ for Jumper

Each temperature / humidity cycle is defined at 8

MIL-STD-202G Method-106G

±(0.5%+0.05 Ω) for 1% tol.

Moisture

hours, 3 cycles / 24 hours for 10d. with 25 °C /

Resistance

±(2.0%+0.05 Ω) for 5% tol.

65 °C 95% R.H, without steps 7a & 7b,

<100 mΩ for Jumper

unpowered Parts mounted on test-boards, without condensation on parts Measurement at 24±2 hours after test conclusion

MIL-STD-202G Method-107G

±(0.5%+0.05 Ω) for 1% tol.

Thermal Shock

-55/+125 °C Number of cycles required is 300. Devices

±(1%+0.05 Ω) for 5% tol.

unmounted

<50 mΩ for Jumper

Maximum transfer time is 20 seconds. Dwell time is 15 minutes. Air – Air

2.5 times of rated voltage or maximum overload

IEC60115-1 4.13

±(1.0%+0.05 Ω) for 1% tol.

Short Time

voltage whichever is less for 5 sec at room

Overload

±(2.0%+0.05 Ω) for 5% tol.

temperature

<50 mΩ for Jumper No visible damage

Page 7

PDF page 7 diagram

TEST

TEST METHOD

IEC 60068-2-21

Board Flex/ Bending

IEC 60068-2-1

Low Temperature Operation

IEC 60115-1 4.6

Insulation Resistance

Type

IEC 60115-1 4.7

Dielectric Withstand

Type

Voltage

IPC/JEDEC J-STD-020D

Resistance to Solvent

brushing

IEC 60115-1 4.12

Noise

IEC 60115-1 4.37

Biased Humidity (steady state)

PROCEDURE

REQUIREMENTS

±(1.0%+0.05 Ω) for 1%, 5% tol.

Chips mounted on a 90mm glass epoxy resin PCB (FR4)

<50 mΩ for Jumper

3 mm bending

No visible damage

Bending time: 60±5 seconds

±(0.5%+0.05 Ω) for 1% tol .

The resistor shall be subjected to a DC rated voltage for 1.5 h-on, 0.5 h-off, at -55±3 °C

±(1.0%+0.05 Ω) for 5% tol.

This constitutes shall be repeated for 96 hours

No visible damage

However the applied voltage shall not exceed the maximum operating voltage

≥10 GΩ

Rated continuous overload voltage (RCOV) for 1 minute

RC0805

Voltage (DC)

100 V

No breakdown or flashover

Maximum voltage (Vrms) applied for 1 minute

RC0805

Voltage (AC)

300 Vrms

lsopropylalcohol (C3H7OH) followed by

No smeared

Value

Resistors range

Maximum voltage (Vrms) applied

R < 100 Ω

10 dB

100 Ω ≤ R < 1 KΩ

20 dB

1 KΩ ≤ R < 10 KΩ

30 dB

10 KΩ ≤ R < 100 KΩ 40 dB 100 KΩ ≤ R < 1 MΩ 46 dB 1 MΩ ≤ R ≤ 22 MΩ

48 dB

±(1.0%+0.05 Ω) for 1% tol.

Steady state for 1000 hours at 40 °C / 95% R.H. RCWV applied for 1.5 hours on and

±(2.0%+0.05 Ω) for 5% tol.

0.5 hour off

<100 mΩ for Jumper

Page 8

PDF page 8 diagram

TEST

TEST METHOD

PROCEDURE

REQUIREMENTS

2.5 times of rated voltage or maximum

IEC 60115-1 4.39

±(1.0%+0.05 Ω) for 1% tol.

Intermittent

overload voltage whichever is less for 1 second

Overload

±(2.0%+0.05 Ω) for 5% tol.

on and 25 seconds off; total 10,000 cycles

Solderability

IPC/JEDEC J-STD-002B test B

  • Wetting

Electrical Test not required Magnification 50X SMD conditions:

<100 mΩ for Jumper

Well tinned (≥95% covered) No visible damage

1st step: method B, aging 4 hours at 155 °C dry heat 2nd step: leadfree solder bath at 245±3 °C Dipping time: 3±0.5 seconds

Leadfree solder, 260 °C, 30 seconds

IPC/JEDEC J-STD-002B test D

  • Leaching

No visible damage

immersion time

Condition B, no pre-heat of samples

IEC 60068-2-58

±(0.5%+0.05 Ω) for 1% tol .

  • Resistance to Soldering Heat

Leadfree solder, 260 °C, 10 seconds

±(1.0%+0.05 Ω) for 5% tol.

immersion time

<50 mΩ for Jumper

Procedure 2 for SMD: devices fluxed and

No visible damage

cleaned with isopropanol

Page 9

PDF page 9 diagram

REVISION HISTORY

CHANGE NOTIFICATION DESCRIPTION

REVISION DATE

  • Test Items and methods updated

Version 4 Jun 16, 2009 -

  • Test requirements upgraded
  • Change to dual brand datasheet that describe RC0805 with RoHS compliant

Version 3 Jul 15, 2008 -

  • Description of "Halogen Free Epoxy" added
  • Define global part number
  • New datasheet for 0805 thick film 1% and 5% with lead-free terminations

Version 2 Sep 03, 2004 -

  • Replace the 0805 part of pdf files: RC01_11_21_31_5, RC02_12_22_32_10, and HRC11_5_4
  • Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) - High ohmic products combined into standard products.

“ Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any product change will be announced by PCN.”