4003536 CLARKE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 8
Technical content
Datasheet sections
ORIGINAL INSTRUCTIONS GC07/23 UNDERBONNET WORKLIGHT MODEL NO: UBL1600R PART NO: 4003536
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com INTRODUCTION Thank you for purchasing this CLARKE worklight. This underbonnet lamp incorporates a telescopic beam and two rubber coated brackets to assist in positioning in the underbonnet area. The LED lamp gives complete engine bay illumination without the inconvenience of a mains cable. The magnet at each end provides an alternative method of mounting the unit against a car body. Before attempting to use this worklight, please read this manual thoroughly and follow the instructions carefully. GUARANTEE This worklight is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the worklight is found to have been abused or tampered with in any way, or not used for its intended purpose. Faulty goods should be returned to their place of purchase, no worklight can be returned to us without prior permission. This guarantee does not effect your statutory rights. ENVIRONMENTAL RECYCLING POLICY Through purchase of this worklight, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE. In effect, this means that this worklight must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility. The light source contained in this worklight has a life expectancy of approximately 50000 hours after which the worklight should be disposed of in an environmentally responsible way. The Lithium Ion battery falls under the Waste Batteries and Accumulators Regulations 2009 and should be disposed of in a controlled manner.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SAFETY INSTRUCTIONS 1. ALWA YS check for damage before using the worklight. Inspect the power cable and plug for damage. Any damage should be properly repaired or the part replaced. Consult your local CLARKE dealer. 2. ALWA YS ensure that the voltage marked on the charger matches the power supply to be used. 3. NEVER use this lamp in a bathroom or in the vicinity of a swimming pool. 4. NEVER cover the lamp. 5. NEVER pull the cable to remove the charger plug from the power supply. 6. DO NOT look directly into the worklight when it is switched on. 7. Keep the worklight out of the reach of children. 8. Charge the worklight in a dry indoor location. DO NOT immerse in water or any other liquid. 9. ALWA YS fully charge before first use. 10. DO NOT turn on the light when charging. 11. DO NOT leave the worklight on charge for more than 24 hours. 12. DO NOT disassemble the worklight as there are no user changeable parts. 13. This worklight utilises a rechargeable Lithium-ion battery that can rupture, ignite and cause serious injury if being used improperly. 14. DO NOT put batteries and the worklight in the fire or high temperature. 15. DO NOT puncture or damage the batteries. 16. DO NOT immerse or expose the worklight to water. 17. DO NOT dispose of the worklight in a fire or water. THE FOLLOWING WARNING SYMBOLS ARE FOUND ON THE PRODUCT Indoor use Harmful to aquatic life Pacemaker hazard (due to magnet) Not suitable for use by children
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com OPERATION SWITCHING ON AND OFF 1. Press the power button to ensure there is enough power before use. If low battery power or no power, continue to charge the worklight. 2. Press the power button to turn on. Press and hold the power button and the brightness will drop to 20%. Press and hold again and the brightness can be cycled between 100%, 20% and Off. The light flashes to show the setting has changed. During use, the battery conditio n display will remain illuminated. MOUNTING TO A CAR BONNET To mount to an open car bonnet, extend the telescopic section until the brackets can be used to clamp the worklamp across the bonnet. Note that the mounting hooks will not grip if the bonnet is raised over 45o. Take extra care that the brackets do not slide down if the bonnet is wet. Extend the lamp against the tension of the internal spring to suit the location. The minimum size bonnet width is 1.15m meaning that the worklamp will not fit across small cars such as the Citroen C1, Toyota Yaris etc but can be used if fitted diagonally.
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com SPECIFICATION AND COMPONENT PARTS Model UBL1600R Operating voltages 7.4V(light), 230V(charger) LED Wattage consumption 16W LED replaceable No Rechargable Lithium battery 7.4V / 2600mAh Lighting source 32LEDs Light output (luminous flux) 250-1600 Lumens Colour temperature (rendering) 5500-8500K Ingress Protection (IP rating) IP20 Insulation Class III on light / II on charger Battery charging time 1.5 - 2.5hours@2A, 2.5-3.5@1A Approximate Run Time Power @ 20% 9 Hours Power @ 100% 1 Hour 30 mins Rated lamp lifetime 50,000 hours Efficiency (Lm/W) 150 ML Operating temperatures 0 to + 45 oC Dimension 175 x 1160 x 105mm Weight 1.35Kg
1 Hook 5 Extendable sleeve 9 Main circuit board
2 Upper left housing 6 Aluminium Tube 10 Battery Pack
3 Lower left housing 7 Upper right housing / Screw
4 Strip Light set 8 Lower right housing / Charging pack
Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com DECLARATIONS OF CONFORMITY