DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 3

Technical content

Electronics Specification 01-June-2005 Rev O ATX Power Connector 1. SCOPE This specification covers performance, tests and quality requirements for ATX POWER Connector. 2. APPLICABLE DOCUMENT The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. Test Report: 501-57652 3. REQUIREMENT 3.1. DESIGN AND CONSTRUCTION Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2. MATERIAL A. Contact: Copper Alloy, Tin plated over Nickel all over. B. Housing: High temperature plastic material UL94V-0 3.3. RATINGS A. Current Rating: 9 amps B. Voltage Rating: 250 VAC C. Insulator resistance: 1000 MQ min D. Operating temperature: -25°C to +85°C 3.4. TEST CONDDITION The product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure1. DWN DATE | APVD DATE Angus Wu 01-JUN-2005 | Wei-Jer Ke 01-JUN-2005 TYCO Holdings (Bermuda) VII LTD. This specification is a controlled document. Electronics Peishen Road, Shenkeng, Taipei 222, Taiwan, ROC. TEL : 886-2-2664-9977 Loc DW

3.5. TEST REQUIREMENTS AND PROCEDURES SUMMARY drawing specification applicable quality inspection plan Termination Resistance }20 mQ Max initial EIA-364-23B P= —nee Sema to 20 mV max open circuit at 100 mV max Insulation Resistance 1000 MQ Min EIA-364-21C P| Eee insulation resistance between the adjacent contacts of mated and unmated connector assemblies Voltage Flashover shall occur. Test between adjacent contacts of mated and unmated connector assemblies, apply 1500 VAC for 1minute Measure the force necessary to mate the connector assemblies at rate of 25.4mm/min Measure the force necessary to mate the lconnector assemblies at rate of 25.4mm/min Apply axial load at a rate of 25.4mm/min Connector were mated and unmated 50 cycles at a rate of travel at 25.4mm/minute Thermal Shock See Note EIA-364-32C eS -55°C_ and 85'C in 30 minutes each Humidity See Note EIA-364-31B Subject mated connectors to between25°C at and 65°C at 90~95% RH for 96hours. Subject mated samples to 5% slat spray at 35) C for 48 hours Solderability See Note Soldering time:5+0.5sec. Solder Temperature:| 230+5°C ,0.5mm from terminal tip and fitting nail tip Subject mated samples to 105°C for 96 hours Soldering Heat Solder Temp. : 265+5°C for 10+0.5 sec Figure 1 NOTE: Shall meet visual requirements, show no physical damage. Rev O 20f3

3.6. QUALIFICATION TEST SEQUENCE | testssoninin FRE Tes eT ContactResistance | 37 | 24 | TUT UT linsulation Resistance [| | 2 TT [Dielectric Withstand Voltage [| | 7 | 36 TY IMatingForce TUT JUnmatingForce dT 4 TUT |Contact RetentionForce [| | CT Durability TT JSolderability TT [ThermalShock TT |Humidity Temp. Cycling [| | TS [TemperatureLife | TT JSaltSpray CE [Resistance to Wave SolderingHeat{ [TT Figure 2 NOTE: The numbers indicate sequence in which tests are performed. Rev O 3 of 3