Download PDF3SBH-3SDH MACOM
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 4
Technical content
Code 7: Lato rid-space Guide M 7. -_ 8 icro-miniature coos Relays a A Type 3SBH (4PDT) Other Specifications Operate Time: 4ms max. Contact Ratings: Release Time: DC resistive—2 amps at 28 volts 4 ms max. Features DC inductive —0.5 amps at 28 volts, Bounce: * Low profile...only 0.32 inch high 200 mH 15 millisecond * Long life version available AC resistive—0.5 amps at 115 volts, 400 4 . + MIL-R-39016/14 or 60 Hz (enclosure isolated from ground, Dielectric Strength: orenclosure and movable contactatsame 500 volts rms at sea level; a potential) 350 volts rms at 70,000 feet Description AC. 0.125 amps at 115 volts (enclosure at Insulation Resistance: This 150 four pole double throw Grid- line potential with respect to movable 1,000 megohms minimum over space relay is the companion to the two contact) temperature range pole 3SBC type shown on page 10. It also Low level—low-level operation at 50 Vibration: features the same .150 inch pin spacing millivolts, 30 microamps, 33-ohm miss 306, t 3000 H. that allows you to insert the relay with no level to z intermediate pin spreaders. There is Contact Resistance: Shock: adequate clearance for conductors to 0.050 ohms max.: 0.150 ohms after life 100 at 11 ms reach all pins. It is a very compact 4 pole test . Temperature: double throw 2 ampere relay. Life: ~65C to +125C 100,000 operations at rated loads listed; See page 19 for Mounting Forms, 1,000,000, operations at low-level loads Terminals and Circuit Diagrams. F Coil Table (All Values DC)* Type 3SBH, 4 Pole Relay —250 mW Sensitivity: (Code 1) B SENSITIVITY CODE: 1 Voltage Calibrated, Code: 5 F Release Voltage Code Resistance Source Operate Range at 25C Letter at 25C ohms Voltst Volts at 25C ee ee B 28% 10% 4.0- 70 27 16 03 D 73+ 10% 6.0-11.0 42 25 04 = E 115 = 10% 8.0-14.0 5.4 32 06 G 280 * 10% 12 -220 84 5.0 08 H 430+ 10% 15 -26.0 103 6.0 1.0 K 720 + 10% 20 -36.0 135 84 15 N 1040 + 10% 26 -46.0 175 105 19 * Values listed are Factory test and inspection values. User should t Applicable over the operating temperature range in circulating air. ‘allow for meter variations, ORDERING Example: The relay selected in this ex- ample is a 4PDT 150-grid relay, voltage cet Catalog No INSTRUCTIONS calibrated end bracket mounting, 0.13- Game” = 988H 5S TKS inch solder hook header, 720 ohms coil A, ft t Catalog-selected Relays: The catalog resistance, and 250 mW sensitivity. By Type number is derived by choosing the proper _ choosing the proper code for each of GEM Calibration — | CODE for each of the six relay charac- these relay characteristics, the catalog AE Mounting ———J teristics in the order in which the codes number is identified as 35BH5131K5 PM icaser ——_ are listed. Use the location guide (letters The letter R following sensitivity code : a in vertical red columns) to find each indicates relay received 5000 operation , oe CODE easily. miss-test. Ex. 35BH5131K5R, Sensitivity, ————____ k
tyca / Electronics @i 4 +] Code rid-space ri Location . = @8 Pie. Guide Micro-miniature Ke Ry {ae ay , Type 3SBH (4PDT) Other Specifications Release Time: 6 ms max. Contact Ratings: Bounce: Features DC resistive — 2 amps at 28 volts 2.0 millisecond DC inductive —0.5 amps at 28 volts, ° * Low profile...only 0.32 inch high 200 mH Dielectric Strength: Note (1) + Long life version available AC resistive —0.5 amps at 115 volts, 400 500 volts rms at sea level, * MIL-R-39016/53 & 54 or 60 Hz (enclosure isolated from ground, 350 volts rms at 70,000 feet arenciosure andmovablecontactetsame | ‘nti potential) insulation Resistance: Note (1) Description AC 0.125 amps at 115 volts (enclosure at 4,000 megohms minimum over The 4PDT .150 Grid-space hybrid relays line potential with respect to movable temperature range are advanced designs of the standard high contact) | reliability 4PDT .150 Grid-space relays. ow-level —S0 pA al m i In the single diode version, the relay coil- Peak AC or DC Semiconductor . back electromotive force is suppressed . Characteristics at 25C: to prevent circuit/component damage. Contact Resistance: With the dual diode version, a steering 0,050 ohms max.; Max. Negative Transient: 1 volt diode is added to the coil circuit, along 0.150 ohms after life test Breakdown voltage: 100VDC @ 10a with the suppression diode. This steering 7 Minimum diode prevents operation of the relay by Life: Max. Leakage Current: 1 microamp @ reverse polarity voltages and protects 100,000 operations at rated loads listed; sovoG the suppression diode. The single diode 1,000,000, operations at low-level loads . version is qualified to MIL-R-39016/53 : Note (1): Tests for dielectric withstanding and the dual diode is qualified to Operate Time: voltage and insulation resistance should MIL-R-39016/54 4ms max. be made with “coil terminals” shorted together to avoid unnecessary electrical stress to semiconductor elements. See page 19 for Mounting Forms, Terminals and Circuit Diagrams. Coil Table (All Values DC)* Type 3SBH, 4 Pole Relay — 250 mW Sensitivity: (Code 5 single diode, Code 6 dual diodes) Single Diode SENSITIVITY CODE: 5 Voltage Calibrated, Code: 5 Release Voltage Code Resistance Source Operate Range at 25C Letter at 25C ohms Voltst Volts at 25C [Mex Min B 28+ 10% 40- 70 27 16 03 : D 73 10% 6.0-11.0 42 25 04 E 115 + 10% 8.0-14.0 5.4 32 06 G 280 + 10% 12 -22.0 84 5.0 o8 H 430 + 10% 15 -260 103 6.0 1.0 , K 720 + 10% 20 -35.0 13.5 84 15 N 1040 = 10% 26 -46.0 175 105 19 Dual Diode SENSITIVITY CODE: 6 B 28 > 10% 4.0- 7.0 37 23 05 D 73* 10% 6.0-11.0 52 3.2 06 E 115 = 10% 8.0-14.0 64 39 08 G 280 = 10% 12.0-22.0 94 57 1.0 H 430 = 10% 15 -26.0 11.3 67 1.2 K 720 * 10% 20 -35.0 14.5 88 17 N 1040 = 10% 26 -46.0 18.4 44 24 *Values listed are factory test and inspection values. User should allow for meter variations. +Applicable over the operating temperature range in circulating air.
Location ONG=ire Guide . icro-miniature as al 100,000,000 Operations Type 3SDH (4PDT) Other Specifications Operate Time: @ +25°C ms max. Contact Ratings: . 0, DC resistive—2 amps at 28 volts, Release Time: @ + 25°C Features (DC 100,000 operations) B ms max. @ 425°C . DC inductive —0.3 amp at 28 volts, ounce: @ Long life at low level or signal loads. (L/R not greater than 0.008) 1.5 millisecond * Low profile... only 0.32 inch high AC resistive 05 am pat 115 volts, 400 Dielectric Strength: or 60 Hz (enclosure isolated from electric Strength: ae ground, or enclosure and movable con- 500 volts rms at sea level; Description tact at same potential) <0 vols rms 5 7o,000 feet AC resistive 0.125 amps at 115 volts insulation Resistance: The 3SDH relay is designed for 100,000,000 operations at low levels. It {enclosure atine potential with respect 1,000 megohms minimum over is a four pole double throw Grid-spaced Low-level--50 4A, temperature range relay. The 0.150 inch pin spacing allows ow- level — 50 nA at 50 mV Vibration: Peak AC or DC the user to insert the relay with no inter- 5 30G, to 3000 Hz mediate pin spreaders. There is adequate Contact Resistance: Shock: clearance for conductor to reach all pins. 0.050 ohms max.; 0.150 ohms after life 100G at 11 ms tests Life: Temperature: ife: — 40C to +125C 100,000 operations at rated loads lifted; 100,000,000 operations @ low-level loads See page 19 for Mounting Forms, Terminals and Circuit Diagrams. Coil Table (All Values DC)*Type 3SDH, 4 Pole Relay—210mW Sensitivity: (Code 1) SENSITIVITY CODE: 1 Voltage Calibrated, Code: § lease Voltage Code Resistance Source Operate Range at25¢ Letter at 25C ohms Voltst Volts at 25C B 28+ 10% 4.0- 70 3.0 16 03 D 73 + 10% 6.0-11.0 48 25 04 E 115 * 10% 8.0-14.0 59 32 06 G 280 +: 10% 12-220 93 5.0 08 H 430 + 10% 15 -26.0 11.5 60 1.0 K 720 + 10% 20 -35.0 149 8.1 15 N 1040+ 10% 26 -46.0 179 105 19 * Values listed are Factory test and inspection values. User should t+ Applicable over the operating temperature range in circulating air. allow for meter variations.
Mounting Forms (3SBH, 3SDH) Location (Vibration note with each form is acceleration from 55 to 3000 Hz) No Mount End Bracket Cc [00 sg sg “Assumes relay held securely by potting or 1062 mox other means. fo 8802 010. I 4 098 sia Header Types +0 nes bee = D a | ea i sto sho .020] 0 Tea at me eee Solder hook | 0.3 1 --- __ Straight pin] 0.12 | CODE: 1 All dimensions in inches Straight pin ‘socket or Z+ .020 TOLERANCES PCB type) 9.19 (Unless otherwise specified) [straignt pin] 0.25 Hundreaths =0.020 CODES: Thousandths 0.005 4,5,8 Thousandths _ Header and Connection Diagrams CODE1 CODES CODE6 4-Pole Terminal View F blue beod blue beod biveveos 1 ree | pee 7 Leg $ 3 3 43 t J 3 —— co a a a a re tT 44 T 1! RL CODE1 CODES &6 blue beos blue beod ia © smal 5 ina © eal <r Stee o 4m Bo + ol 2” le ool 2° neoendc Sr oole Ce Ca a) | his Le 300: 300- 450 450 Terminals .020 dia ORDERING Example: The relay selected in this ex- ample is a 4PDT 150-grid relay, voltage 12n Catalog No. INSTRUCTIONS calibrated end bracket mounting, 0.13- eae gH 5 19 1 KOS inch solder hook header, 720 ohms coil A ft t + Catalog-selected Relays: The catalog resistance, and 250 mW sensitivity. By ‘ Bg | number is derived by choosing the proper choosing the proper code for each of 8 Calibration | CODE for each of the six relay charac- these relay characteristics, the catalog c Mounting ————_. teristics in the order in which the codes number is identified as 35 BH5131KS. PME ieacer are listed. Use the location guide (letters The letter R following sensitivity code Ee Cou Resist in vertical red columns) to find each indicates relay received 5000 operation pay C0" Resistance CODE easily. miss-test. Ex. 35BH5131K5R Sensitivity ———_———____ Tyco Electronics Corporation wwwtycoelectronics.com 800-522-6752 (US.A) or 717-564-0100 Speeifications subject to change, Cll and TYCO are trademarks. © 2003 by Tyco Electronics Corporation