3803 RENESAS
Document overview
- Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 119
Technical content
Rev.1.00 Apr 2, 2007 Page 1 of 117 REJ03B0212-0100
DESCRIPTION
The 3803 group (Spec.L) is the 8-bit microcomputer based on the 740 family core technology. The 3803 group (Spec.L) is designed for household products, office automation e quipment, and controlling systems that require analog signal processi ng, including the A/D converter and D/A converters.
FEATURES
(at 16.8 MHz oscillation frequency)
- Memory size
- Interrupts (external 8, internal 12, software 1) 8-bit × 4 (with 8-bit prescaler) 8-bit × 1 (Clock-synchronized) (8-bit reading enabled) (connect to external ceramic resonator or quartz-crystal oscillator)
- Power source voltage (Mask ROM version) [In high-speed mode] [In middle-speed mode] [In low-speed mode]
- Power source voltage (Flash memory version) [In high-speed mode] [In middle-speed mode] [In low-speed mode]
- Power dissipation (Mask ROM version) (at 16.8 MHz oscillation frequency, at 5 V power source voltage) (at 32 kHz oscillation frequency, at 3 V power source voltage)
- Power dissipation (Flash memory version) (at 16.8 MHz oscillation frequency, at 5 V power source voltage) (at 32 kHz oscillation frequency, at 3 V power source voltage)
- Packages <Flash memory mode>
- Program/Erase control by software command <Notes> The flash memory version cannot be used for application embedded in the MCU card. 3803 Group (Spec.L) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER REJ03B0212-0100 Rev.1.00 Apr 2, 2007
Rev.1.00 Apr 2, 2007 Page 2 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 1. Pin configuration (Top view) PLQP 0064KB-A (64P6Q-A)/PLQP0064GA-A (64P6U-A) Fig 2. Pin configuration (Top view) (PRDP0064BA-A (64P4B)) P20(LED0) M38039MFL-XXXHP/KP M38039FFLHP/KP 47 P35/TXD3 P34/RXD3 P31/DA2 P30/DA1 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P37/SRDY3 P36/SCLK3 P33 P32 VSS XOUT XIN P42/INT1 RESET CNVSS P40/INT40/XCOUT P41/INT00/XCIN P27(LED7) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P21(LED1) P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR 1 P54/CNTR 0 P52/SCLK2 P51/SOUT2 P50/SIN2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P62/AN2 P47/SRDY1 /CNTR 2 P53/SRDY2 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P16 P14 P15 P17 641 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P53/SRDY2 P52/SCLK2 P51/SOUT2 P47/SRDY1/CNTR2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS VSS RESET P41/INT00/XCIN P40/INT40/XCOUT XIN XOUT P50/SIN2 P30/DA1 P31/DA2 P32 P33 P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P13 P14 P15 P16 P17 P20(LED0) P21(LED1) P22(LED2) P12 P23(LED3) P24(LED4) P25(LED5) P26(LED6) M38039MFL-XXXSP M38039FFLSP P27(LED7)
Rev.1.00 Apr 2, 2007 Page 3 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 3. Pin configuration (Top view) (PTLG0064JA-A (64F0G)) P61/AN1 P60/AN0 P55/CNTR1 P52/SCLK2 P50/SIN2 P44/RXD1 P43/INT2 CNVSS P65/AN5 P64/AN4 P56/PWM P5 3/SRDY2 P51/SOUT2 P46/SCLK1 P42/INT1 RESET P67/AN7 P66/AN6 P57/INT3 P54/CNTR0 P47/SRDY1/CNTR2 P45/TXD1 P40/INT40/XCOUT P41/INT00/XCIN P30/DA1 P31/DA2 P32 P37/SRDY3 P17 P14 P15 P16 P33 P34/RXD3 P00/AN8 P05/AN13 P12 P13 P26(LED6)P 2 7(LED7) P35/TXD3 P01/AN9 P03/AN11 P06/AN14 P11/INT01 P25(LED5)P 2 3(LED3)P 2 4(LED4) P36/SCLK3 P02/AN10 P04/AN12 P07/AN15 P10/INT41 P20(LED0)P 2 1(LED1)P 2 2(LED2) P62/AN2 P63/AN3 VREF AVSS VCC VSS XIN XOUT ABCDEFGH ABCDEFGH Package (TOP VIEW) 50 46 44 41 40 32 31 30 51 47 45 42 39 27 29 28 53 52 48 43 38 37 26 25 56 55 54 49 33 36 35 34 1 64 58 59 57 24 22 23 60 61 4 7 12 14 21 20 62 63 5 8 10 13 17 19 2 3 6 9 11 15 16 18 PIN CONFIGURATION (TOP VIEW) Note : The numbers in circles corresponds with the number on the packages FP/HP/KP. M38039MFL -XXXWG M38039 FFLWG
Rev.1.00 Apr 2, 2007 Page 4 of 117 REJ03B0212-0100 3803 Group (Spec.L) Table 1 Performance overview Parameter Function Number of basic instructions 71 Minimum instruction execution time 0.24 µs (Oscillation frequency 16.8 MHz) Oscillation frequency Oscillation frequency 16.8 MHz(Maximum) Memory sizes Mask ROM version ROM 60 Kbytes RAM 2048 bytes Flash memory version ROM 60 Kbytes RAM 2048 bytes I/O port P0-P6 56 pins Software pull-up resistors Built-in Interrupt 21 sources, 16 vectors (8 external, 12 internal, 1 software) Timer 8-bit × 4 (with 8-bit prescaler), 16-bit × 1 Serial interface 8-bit × 2 (UART or Clock-synchronized) 8-bit × 1 (Clock-synchronized) PWM 8-bit × 1 (with 8-bit prescaler) A/D converter 10-bit × 16 channels (8-bit reading enabled) D/A converter 8-bit × 2 channels Watchdog timer 16-bit × 1 LED direct drive port 8 (average current: 15 mA, peak current: 30 mA, total current: 90 mA) Clock generating circuits Built-in 2 circuits (connect to external ceramic rasonator or quartz-crystal oscillator) Power source voltage In high-speed mode At 16.8 MHz Mask ROM version 4.5 to 5.5 VFlash memory version At 12.5 MHz Mask ROM version 4.0 to 5.5 VFlash memory version At 8.4 MHz Mask ROM version 2.7 to 5.5 VFlash memory version At 4.2 MHz Mask ROM version 2.2 to 5.5 V At 2.1 MHz Mask ROM version 2.0 to 5.5 V In middle- speed mode At 16.8 MHz Mask ROM version 4.5 to 5.5 VFlash memory version At 12.5 MHz Mask ROM version 2.7 to 5.5 VFlash memory version At 8.4 MHz Mask ROM version 2.2 to 5.5 V At 6.3 MHz Mask ROM version 1.8 to 5.5 V In low-speed mode At 32 MHz Mask ROM version 1.8 to 5.5 V Flash memory version 2.7 to 5.5 V Power dissipation In high-speed mode Mask ROM version 40 mW Flash memory version 27.5 mW In low-speed mode Mask ROM version 45 µW Flash memory version 1200 µW Input/Output characteris- tics Input/Output withstand voltage V CC Output current 10 mA Operating temperature range -20 to 85 °C Device structure CMOS sillicon gate Package 64-pin plastic molded SDIP/LQFP/FLGA
Rev.1.00 Apr 2, 2007 Page 5 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 4. Functional block diagram Prescaler X (8) Timer 1 (8) Prescaler 12 (8) Timer X (8) Timer 2 (8) RESET 27 26 CNVSS CNTR 0 Reset input P1 (8) 41 43 45 4742 44 46 48 I/O port P1 Prescaler Y (8) Timer Y (8) CNTR 1 P2 (8) 33 35 37 3934 36 38 40 I/O port P2 (LED drive) P0 (8) 49 50 51 52 53 54 55 56 I/O port P0 D/A converter 1 (8) R A M R O M A X Y S PCLPCH PS C P U VSS VCC D/A converter 2 (8) P5 (8) 13 1714 16 1815 Clock generating circuit XIN XOUT Main clock input Main clock output FUNCTIONAL BLOCK DIAGRAM (Package: PRDP0064BA-A (64P4B)) 30 31 A/D converter (10) VREF PWM (8) 2 3 AVSS XCIN XCOUT Sub-clock input Sub-clock output 28 29 Data bus Timer Z (16) CNTR 2 P6 (8) 468 1 0579 1 1 I/O port P6 1912 I/O port P5 INT3 SI/O2 (8) SI/O1 (8) P4 (8) 21 2522 24 2823 2920 I/O port P4 INT00 INT1 INT2 INT40 P3 (8) 58 6259 61 6360 6457 I/O port P3 SI/O3 (8) INT01 INT41
Rev.1.00 Apr 2, 2007 Page 6 of 117 REJ03B0212-0100 3803 Group (Spec.L) PIN DESCRIPTION Table 2 Pin description Pin Name Functions Function except a port function VCC, VSS Power source • Apply voltage of 1.8 V − 5.5 V to VCC, and 0 V to VSS. In the flash memory version, apply voltage of 2.7 V − 5.5 V to VCC. CNVSS CNVSS input • This pin controls the operation mode of the chip.
- Normally connected to VSS. VREF Reference voltage
- Reference voltage input pin for A/D and D/A converters. AVSS Analog power source
- Analog power source input pin for A/D and D/A converters.
- Connect to VSS. RESET Reset input • Reset input pin for active “L”. XIN Main clock input • Input and output pi ns for the clock generating circuit.
- Connect a ceramic resonator or quartz-crystal oscillator between the XIN and XOUT pins to set the oscillation frequency.
- When an external clock is used, connect the clock source to the XIN pin and leave the XOUT pin open. XOUT Main clock output P00/AN8− P07/AN15 I/O port P0 • 8-bit CMOS I/O port.
- I/O direction register allows each pin to be individually programmed as either input or output.
- CMOS compatible input level.
- CMOS 3-state output structure.
- Pull-up control is enabled in a bit unit.
- P 2 0 − P27 (8 bits) are enabled to output large current for LED drive.
- A/D converter input pin P10/INT41 P11/INT01 I/O port P1 • Interrupt input pin P12−P17 P20(LED0)- P27(LED7) I/O port P2 P30/DA1 P31/DA2 I/O port P3 • 8-bit CMOS I/O port.
- I/O direction register allows each pin to be individually programmed as either input or output.
- CMOS compatible input level.
- P 3 0, P31, P34 − P37 are CMOS 3-state output structure.
- P 32, P33 are N-channel open-drain output structure.
- Pull-up control of P30, P31, P34 − P37 is enabled in a bit unit.
- D/A converter input pin P32, P33 P34/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3
- Serial I/O3 function pin P40/INT40/XCOUT P41/INT00/XCIN I/O port P4 • 8-bit CMOS I/O port.
- I/O direction register allows each pin to be individually programmed as either input or output.
- CMOS compatible input level.
- CMOS 3-state output structure.
- Pull-up control is enabled in a bit unit.
- Interrupt input pin
- Sub-clock generating I/O pin (resonator connected) 2/INT1 P43/INT2
- Interrupt input pin P44/RXD1 P45/TXD1 P46/SCLK1
- Serial I/O1 function pin P47/SRDY1/CNTR2 • Serial I/O1, timer Z function pin P50/SIN2 P51/SOUT2 P52/SCLK2 P53/SRDY2 I/O port P5 • Serial I/O2 function pin P54/CNTR0 • Timer X function pin P55/CNTR1 • Timer Y function pin P56/PWM • PWM output pin P57/INT3 • Interrupt input pin P60/AN0− P67/AN7 I/O port P6 • A/D converter input pin
Rev.1.00 Apr 2, 2007 Page 7 of 117 REJ03B0212-0100 3803 Group (Spec.L) PART NUMBERING Fig 5. Part numbering M3803 9 M F L− XXX SPProduct name Package code SP : PRDP0064BA-A (64P4B) HP : PLQP0064KB-A (64P6Q-A) KP : PLQP0064GA-A (64P6U-A) WG : PTLG0064JA-A (64F0G) ROM number Omitted in the flash memory version.ROM/Flash memory size 1: 4096 bytes 2: 8192 bytes 3: 12288 bytes 4: 16384 bytes 5: 20480 bytes 6: 24576 bytes 7: 28672 bytes 8: 32768 bytes The first 128 bytes and the last 2 bytes of ROM are reserved areas ; they cannot be used as a user’s ROM area. However, they can be programmed or erased in the flash memory version, so that the users can use them. Memory type M: Mask ROM version F: Flash memory version RAM size 0: 192 bytes 1: 256 bytes 2: 384 bytes 3: 512 bytes 4: 640 bytes −: standard Omitted in the flash memory version. L−: Minner spec. change product 9: 36864 bytes A: 40960 bytes B: 45056 bytes C: 49152 bytes D: 53248 bytes E: 57344 bytes F: 61440 bytes 5: 768 bytes 6: 896 bytes 7: 1024 bytes 8: 1536 bytes 9: 2048 bytes
Rev.1.00 Apr 2, 2007 Page 8 of 117 REJ03B0212-0100 3803 Group (Spec.L) GROUP EXPANSION Renesas plans to expand the 3803 group (Spec.L) as follows. Memory Size Packages
- PRDP0064BA-A (64P4B)
- PLQP0064KB-A (64P6Q-A)
- PLQP0064GA-A (64P6U-A)
- PTLG0064JA-A (64F0G) Fig 6. Memory expansion plan NOTE: 1. ROM size includes the ID code area. Table 3 Support products Part No. ROM size (bytes) ROM size for User in ( ) RAM size (bytes) Package Remarks M38039MFL-XXXSP 61440 (61310) 2048 PRDP0064BA-A (64P4B) Mask ROM versionM38039MFL-XXXHP PLQP0064KB-A (64P6Q-A) M38039MFL-XXXKP PLQP0064GA-A (64P6U-A) M38039MFL-XXXWG PTLG0064JA-A (64F0G) M38039FFLSP 57344+4096 (NOTE) 2048 PRDP0064BA-A (64P4B) Flash memory version V CC = 2.7 to 5.5 V M38039FFLHP PLQP0064KB-A (64P6Q-A) M38039FFLKP PLQP0064GA-A (64P6U-A) M38039FFLWG PTLG0064JA-A (64F0G) Memory Expansion Plan 512 12 K 16 K 20 K 24 K 28 K 32 K 384 768 640 8 K 1024896 1280 1152 1408 2048 1536 ROM size (bytes) RAM size (bytes) 40323072 48 K
60 K M38039MFL
Rev.1.00 Apr 2, 2007 Page 9 of 117 REJ03B0212-0100 3803 Group (Spec.L) FUNCTIONAL DESCRIPTION CENTRAL PROCESSING UNIT (CPU) The 3803 group (Spec.L) uses the standard 740 Family instruction set. Refer to the table of 740 Family addressing modes and machine instructions or the 740 Family Software Manual for details on the instruction set. Machine-resident 740 Family instructions are as follows: The FST and SLW instructions cannot be used. The STP, WIT, MUL, and DIV instructions can be used. [Accumulator (A)] The accumulator is an 8-bit register. Data operations such as data transfer, etc. are executed mainly through the accumulator. [Index Register X (X)] The index register X is an 8-bit register. In the index addressing modes, the value of the OPERAND is added to the contents of register X and specifies the real address. [Index Register Y (Y)] The index register Y is an 8-bit register. In partial instruction, the value of the OPERAND is added to the contents of register Y and specifies the real address. [Stack Pointer (S)] The stack pointer is an 8-bit register used during subroutine calls and interrupts. This register indicates start address of stored area (stack) for storing registers during subroutine calls and interrupts. The low-order 8 bits of the stack address are determined by the contents of the stack pointer. Th e high-order 8 bits of the stack address are determined by the st ack page selection bit. If the stack page selection bit is “0”, the high-order 8 bits becomes “00 16”. If the stack page selection bit is “1”, the high-order 8 bits becomes “0116”. The operations of pushing register contents onto the stack and popping them from the stack are shown in Figure 8. Store registers other than those described in Figure 7 with program when the user needs them during interrupts or subroutine calls (see Table 4). [Program Counter (PC)] The program counter is a 16-bit counter consisting of two 8-bit registers PC H and PC L. It is used to indicate the address of the next instruction to be executed. Fig 7. 740 Family CPU register structure Processor Status Register (PS) Carry Flag Zero Flag Interrupt Disable Flag Decimal Mode Flag Break Flag Index X Mode Flag Overflow Flag Negative Flag b7 b0 b15 Program Counter Stack Pointer Index Register Y Index Register X AccumulatorA X Y S PCLPCH CZIDBTVN b7 b0 b7 b0 b7 b0 b7 b0 b7 b0
Rev.1.00 Apr 2, 2007 Page 10 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 8. Register push and pop at interrupt generation and subroutine call Interrupt request(1) M(S)←(PCH) (S)←(S) − 1 M(S)←(PCL) (S)←(S) − 1 Execute RTS Subroutine (S)←(S) + 1 (PCL)←M(S) (S)←(S) + 1 (PCH)←M(S) M(S)←(PCH) (S)←(S) − 1 M(S)←(PCL) (S)←(S) − 1 M(S)←(PS) (S)←(S) − 1 Interrupt Service Routine (S)←(S) + 1 (PS)←M(S) (S)←(S) + 1 (PCL)←M(S) (S)←(S) + 1 (PCH)←M(S) Execute JSR Execute RTI Push Return Address on Stack Push Contents of Processor Status Register on Stack I Flag is Set from “0” to “1” Fetch the Jump Vector POP Contents of Processor Status Register from Stack POP Return Address from Stack POP Return Address from Stack Push Return Address on Stack Note 1 : Condition for acceptance of an interrupt → Interrupt enable flag is “1” Interrupt disable flag is “0” On-going Routine Table 4 Push and pop instructions of accumulator or processor status register Push instruction to stack P op instruction from stack Accumulator PHA PLA Processor status register PHP PLP
Rev.1.00 Apr 2, 2007 Page 11 of 117 REJ03B0212-0100 3803 Group (Spec.L) [Processor status register (PS)] The processor status register is an 8-bit register consisting of 5 flags which indicate the status of the processor after an arithmetic operation and 3 fl ags which decide MCU operation. Branch operations can be perf ormed by testing the Carry (C) flag, Zero (Z) flag, Overflow (V) flag, or the Negative (N) flag. In decimal mode, the Z, V, N flags are not valid. Bit 0: Carry flag (C) The C flag contains a carry or borrow generated by the arithmetic logic unit (ALU) immediately after an arithmetic operation. It can also be changed by a shift or rotate instruction. Bit 1: Zero flag (Z) The Z flag is set if the resu lt of an immediate arithmetic operation or a data transfer is “0”, and cleared if the result is anything other than “0”. Bit 2: Interrupt disable flag (I) The I flag disables all interrupts except for the interrupt generated by the BRK instruction. Interrupts are disabled when the I flag is “1”. Bit 3: Decimal mode flag (D) The D flag determines whether additions and subtractions are executed in binary or decimal. Binary arithmetic is executed when this flag is “0”; decimal arithmetic is executed when it is “1”. Decimal correction is automati c in decimal mode. Only the ADC and SBC instructions can execute decimal arithmetic. Bit 4: Break flag (B) The B flag is used to indicate that the current interrupt was generated by the BRK instruction. The BRK flag in the processor status register is always “0”. When the BRK instruction is used to generate an interrupt, the processor status register is pushed onto the stack with the break flag set to “1”. Bit 5: Index X mode flag (T) When the T flag is “0”, arithmetic operations are performed between accumulator and memory . When the T flag is “1”, direct arithmetic operations a nd direct data transfers are enabled between memory locations. Bit 6: Overflow flag (V) The V flag is used during the addition or subtraction of one byte of signed data. It is set if the result exceeds +127 to − 128. When the BIT instructio n is executed, bit 6 of the memory location operated on by the BIT instruction is stored in the overflow flag. Bit 7: Negative flag (N) The N flag is set if the result of an arithmetic operation or data transfer is negative. When the BIT instruction is executed, bit 7 of the memory location operated on by the BIT instruction is stored in the negative flag. Table 5 Set and clear instructions of each bit of processor status register C flag Z flag I flag D flag B flag T flag V flag N flag Set instruction SEC − SEI SED − SET −− Clear instruction CLC − CLI CLD − CLT CLV −
Rev.1.00 Apr 2, 2007 Page 12 of 117 REJ03B0212-0100 3803 Group (Spec.L) [CPU Mode Register (CPUM)] 003B16 The CPU mode register contains the stack page selection bit, the internal system clock control bits, etc. The CPU mode register is allocated at address 003B16. Fig 9. Structure of CPU mode register CPU mode register (CPUM: address 003B16) b7 b0 Stack page selection bit 0 : 0 page 1 : 1 page Processor mode bits b1 b0 0 0 : Single-chip mode 01 : 1 0 : Not available 11 : Main clock division ratio selection bits b7 b6 00 : φ = f(X IN)/2 (high-speed mode) 01 : φ = f(XIN)/8 (middle-speed mode) 10 : φ = f(XCIN)/2 (low-speed mode) 1 1 : Not available Fix this bit to “1”. Port XC switch bit 0 : I/O port function (stop oscillating) 1:X CIN-XCOUT oscillating function Main clock (XIN-XOUT) stop bit 0 : Oscillating 1 : Stopped
Rev.1.00 Apr 2, 2007 Page 13 of 117 REJ03B0212-0100 3803 Group (Spec.L) MISRG (1) Bit 0 of address 0010 16: Oscillation stabilizing time set after STP instruction released bit When the MCU stops the clock oscillation by the STP instruction and the STP instruction has been released by an external interrupt source, usually, the fixed values of Timer 1 and Prescaler 12 (Timer 1 = 01 16 , Prescaler 12 = FF 16 ) are automatically reloaded in orde r for the oscillation to stabilize. The user can inhibit the automati c setting by settin g “1” to bit 0 of MISRG (address 001016). However, by setting this bit to “1”, the previous values, set just before the STP instruction was executed, will remain in Timer 1 and Prescaler 12. Therefore, you wi ll need to set an appropriate value to each register, in accordance with the oscillation stabilizing time, before executing the STP instruction. Figure 10 shows the structure of MISRG. (2) Bits 1, 2, 3 of address 0010 16: Middle-speed Mode Automatic Switch Function In order to switch the clock mode of an MCU which has a sub- clock, the following procedure is necessary: set CPU mode register (003B 16) --> start main clock oscillation --> wait for oscillation stabilizat ion --> switch to middle-speed mode (or high-speed mode). However, the 3803 group (Spec.L) has the built-in function which automatically switches from low to middle-speed mode by program.
- Middle-speed mode automatic switch by program The middle-speed mode can also be automatically switched by program while operating in lo w-speed mode. By setting the middle-speed automatic switch start bit (bit 3) of MISRG (address 0010 16) to “1” in the condit ion that the middle-speed mode automatic switch set bit is “1” while operating in low- speed mode, the MCU will automatically switch to middle-speed mode. In this case, the oscillation stabilizing time of the main clock can be selected by the middle-speed automatic switch wait time set bit (bit 2) of MISRG (address 0010 16). Fig 10. Structure of MISRG MISRG (MISRG: address 001016) b7 b0 Oscillation stabilizing time set after STP instruction released bit 0 : Automatically set “0116” to Timer 1, “FF16” to Prescaler 12 1 : Automatically set disabled Middle-speed mode automatic switch set bit 0 : Not set automatically 1 : Automatic switching enabled (1) Middle-speed mode automatic switch wait time set bit 0 : 4.5 to 5.5 machine cycles 1 : 6.5 to 7.5 machine cycles Middle-speed mode automatic switch start bit (Depending on program) 0 : Invalid 1 : Automatic switch start(1) Not used (return “0” when read) (Do not write “1” to this bit) Note 1 : When automatic switch to middle-speed mode from low-speed mode occurs, the values of CPU mode register (3B 16) change.
Rev.1.00 Apr 2, 2007 Page 14 of 117 REJ03B0212-0100 3803 Group (Spec.L) MEMORY
- Special Function Register (SFR) Area The Special Function Register area in the zero page contains control registers such as I/O ports and timers.
- RAM The RAM is used for data st orage and for stack area of subroutine calls and interrupts.
- R O M The first 128 bytes and the last 2 bytes of ROM are reserved for device testing and the rest is a user area for storing programs. The reserved ROM area can prog ram/erase in the flash memory version.
- Interrupt Vector Area The interrupt vector area contains reset and interrupt vectors.
- Zero Page Access to this area with only 2 bytes is possible in the zero page addressing mode.
- Special Page Access to this area with only 2 bytes is possible in the special page addressing mode. <Note> Since the contents of RAM are undefined at reset, be sure to set an initial value before use. Fig 11. Memory map diagram RAM area RAM size (bytes) Address XXXX16 192 256 384 512 640 768 896 1024 1536 2048 00FF 013F16 01BF16 023F16 02BF16 033F16 03BF16 043F16 063F16 083F16 ROM area ROM size (bytes) Address YYYY16 4096 8192 12288 16384 20480 24576 28672 32768 36864 40960 45056 49152 53248 57344 61440 F000 E00016 D00016 C00016 B00016 A00016 900016 800016 700016 600016 500016 400016 300016 200016 100016 Address ZZZZ16 F08016 E08016 D08016 C08016 B08016 A08016 908016 808016 708016 608016 508016 408016 308016 208016 108016 RAM ROM 0100 16 0000 16 0040 16 0FF0 16 FF00 16 FFDC16 FFFE16 FFFF16 XXXX16 YYYY16 ZZZZ16 SFR area Interrupt vector area Reserved ROM area (128 bytes) Zero page Special page Reserved ROM area Not used 0FFF 16 SFR area Not used SFR area (Note 1)0FEF16 0FE0 16 Notes 1: Only flash memory version has this SFR area. 2: The reserved ROM area can program/erase in the flash memory version. Note the difference of the mask version.
Rev.1.00 Apr 2, 2007 Page 15 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 12. Memory map of special function register (SFR) 000016 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001116 001216 001316 001416 001516 001616 001716 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16 002016 002116 002216 002316 002416 002516 002616 002716 002816 002916 002A16 002B16 002C16 002D16 002E16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16 Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D) Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS) MISRG Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Transmit/Receive buffer register 1 (TB1/RB1) Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART1 control register (UART1CON) Baud rate generator (BRG1) Serial I/O2 control register (SIO2CON) Watchdog timer control register (WDTCON) Serial I/O2 register (SIO2) Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) Timer Z low-order (TZL) Timer Z high-order (TZH) Timer Z mode register (TZM) PWM control register (PWMCON) PWM prescaler (PREPWM) PWM register (PWM) Baud rate generator 3 (BRG3) Transmit/Receive buffer register 3 (TB3/RB3) Serial I/O3 status register (SIO3STS) Serial I/O3 control register (SIO3CON) UART3 control register (UART3CON) AD/DA control register (ADCON) AD conversion register 1 (AD1) DA1 conversion register (DA1) DA2 conversion register (DA2) AD conversion register 2 (AD2) Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2) Notes1: Do not write any data to these addresses, because these are reserved area. 2: Do not access to the SFR area including nothing. 0FE016 0FE116 0FE216 0FE316 0FE416 0FE516 0FE616 0FE716 0FE816 0FE916 0FEA16 0FEB16 0FEC16 0FED16 0FEE16 0FEF16 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 Flash memory control register 0 (FMCR0) Flash memory control register 1 (FMCR1) Flash memory control register 2 (FMCR2) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Reserved (Note 1) Port P0 pull-up control register (PULL0) Port P1 pull-up control register (PULL1) Port P2 pull-up control register (PULL2) Port P3 pull-up control register (PULL3) Port P4 pull-up control register (PULL4) Port P5 pull-up control register (PULL5) Port P6 pull-up control register (PULL6)
Rev.1.00 Apr 2, 2007 Page 16 of 117 REJ03B0212-0100 3803 Group (Spec.L) I/O PORTS The I/O ports have direction registers which determine the input/output direction of each individual pin. Each bit in a direction register corresponds to one pin, and each pin can be set to be input port or output port. When “0” is written to the bit corresponding to a pin, that pin becomes an input pin. When “1” is written to that bit, that pin becomes an output pin. If data is read from a pin which is set to output, the value of the port output latch is read, not the value of the pin itself. Pins set to input are floating. If a pin set to input is written to, only the port output latch is written to and the pin remains floating. By setting the port P0 pull-up control register (address 0FF0 16) to the port P6 pull-up control register (address 0FF6 16) ports can control pull-up with a program. However, the contents of these registers do not affect ports programmed as the output ports. NOTES: 1. Refer to the applicable sections how to us e double-function ports as function I/O ports. 2. Make sure that the input level at each pin is either 0 V or V CC during execution of the STP instruction. When an input level is at an intermediate potential, a current will flow from VCC to VSS through the input-stage gate. Table 6 I/O port function Pin Name Input/ Output I/O Structure Non-Port Function Related SFRs Ref. No. P00/AN8−P07/AN15 Port P0 Input/output, individual bits CMOS compatible input level CMOS 3-state output A/D converter input AD/DA control register (1) P10/INT41 P11/INT01 Port P1 External interrupt input Interrupt edge selection register (2) P12−P17 (3) P20(LED0)− P27(LED7) Port P2 P30/DA1 P31/DA2 Port P3 D/A converter output AD/DA control register (4) P32, P33 CMOS compatible input level N-channel open-drain output (5) 4/RXD3 P35/TXD3 P36/SCLK3 P37/SRDY3 CMOS compatible input level CMOS 3-state output Serial I/O3 function I/O Seri al I/O3 control register UART3 control register (6) (7) (8) (9) 0/INT40/XCOUT P41/INT00/XCIN Port P4 External interrupt input Sub-clock generating circuit Interrupt edge selection register CPU mode register (10) (11) P42/INT1 P43/INT2 External interrupt input Interrupt edge selection register (2) P44/RXD1 P45/TXD1 P46/SCLK1 Serial I/O1 function I/O Seri al I/O1 control register UART1 control register (6) (7) (8) P47/SRDY1/CNTR2 Serial I/O1 function I/O Timer Z function I/O Serial I/O1 control register Timer Z mode register (12) P50/SIN2 P51/SOUT2 P52/SCLK2 P53/SRDY2 Port P5 Serial I/O2 function I/O Se rial I/O2 control register (13) (14) (15) (16) 4/CNTR0 P55/CNTR1 Timer X, Y function I/O Timer XY mode register (17) P56/PWM PWM output PWM control register (18) P57/INT3 External interrupt input Interrupt edge selection register (2) P60/AN0−P67/AN7 Port P6 A/D converter input AD/DA control register (1)
Rev.1.00 Apr 2, 2007 Page 17 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 13. Port block diagram (1) (5) Ports P32, P33 (7) Ports P35, P45 (4) Ports P30, P31 Data bus A/D converter input (1) Ports P0, P6 (6) Ports P34, P44 Serial I/O enable bit (2) Ports P10, P11, P42, P43, P57 (3) Ports P12 to P17, P2 Serial I/O output P-channel output disable bit (8) Ports P36, P46 Pull-up control bit Pull-up control bit Port latch Direction register Pull-up control bit Data bus Port latch Direction register Data bus Port latch Direction register Analog input pin selection bit Data bus Interrupt input Pull-up control bit Port latch Direction register Data bus Pull-up control bit Port latch Direction register Data bus D/A converter output Pull-up control bit Port latch Direction register DA1 output enable bit (P30) DA2 output enable bit (P31) Data bus Port latch Direction register Serial I/O input Receive enable bit Serial I/O enable bit Transmit enable bit Serial I/O mode selection bit Serial I/O clock output Serial I/O external clock input Serial I/O enable bit Pull-up control bit Data bus Port latch Direction register Serial I/O synchronous clock selection bit Serial I/O enable bit
Rev.1.00 Apr 2, 2007 Page 18 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 14. Port block diagram (2) (13) Port P50 (12) Port P47 (9) Port P37 (14) Port P51 (10) Port P40 (11) Port P41 INT40 Interrupt input Serial I/O3 mode selection bit Serial I/O3 ready output Serial I/O3 enable bit Pull-up control bit Data bus Port latch Direction register SRDY3 output enable bit Port XC switch bit Pull-up control bit Data bus Port latch Direction register Port XC switch bit INT00 Interrupt input Port XC switch bit Pull-up control bit Data bus Port latch Direction register Sub-clock generating circuit input Timer output CNTR2 interrupt input Pull-up control bit Data bus Port latch Direction register Serial I/O2 output Pull-up control bit Data bus Port latch Direction register Serial I/O2 transmit completion signal Serial I/O2 port selection bit Pull-up control bit Data bus Port latch Direction register Serial I/O2 input Serial I/O1 mode selection bit Serial I/O1 enable bit SRDY1 output enable bit Bit 2 Bit 1 Bit 0 Timer Z operating mode bits Serial I/O1 ready output P-channel output disable bit Port XC switch bit
Rev.1.00 Apr 2, 2007 Page 19 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 15. Port block diagram (3) (18) Port P56 (15) Port P52 (16) Port P53 (17) Ports P54, P55 CNTR Interrupt input Pull-up control bit Data bus Port latch Direction register PWM output PWM function enable bit Pull-up control bit Data bus Port latch Direction register Serial I/O2 clock output Pull-up control bit Data bus Port latch Direction register Serial I/O2 port selection bit Serial I/O2 synchronous clock selection bit Serial I/O2 external clock input Serial I/O2 ready output Pull-up control bit Data bus Port latch Direction register SRDY2 output enable bit Pulse output mode Timer output
Rev.1.00 Apr 2, 2007 Page 20 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 16. Structure of port pu ll-up control register (1) b7 b0 Port P0 pull-up control register (PULL0: address 0FF016) P00 pull-up control bit 0: No pull-up 1: Pull-up P01 pull-up control bit 0: No pull-up 1: Pull-up 2 pull-up control bit 0: No pull-up 1: Pull-up P03 pull-up control bit 0: No pull-up 1: Pull-up 4 pull-up control bit 0: No pull-up 1: Pull-up P05 pull-up control bit 0: No pull-up 1: Pull-up 6 pull-up control bit 0: No pull-up 1: Pull-up 7 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected. b7 b0 Port P1 pull-up control register (PULL1: address 0FF116) P10 pull-up control bit 0: No pull-up 1: Pull-up P11 pull-up control bit 0: No pull-up 1: Pull-up 2 pull-up control bit 0: No pull-up 1: Pull-up P13 pull-up control bit 0: No pull-up 1: Pull-up 4 pull-up control bit 0: No pull-up 1: Pull-up P15 pull-up control bit 0: No pull-up 1: Pull-up P16 pull-up control bit 0: No pull-up 1: Pull-up 7 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected.
Rev.1.00 Apr 2, 2007 Page 21 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 17. Structure of port pu ll-up control register (2) b7 b0 Port P2 pull-up control register (PULL2: address 0FF216) P20 pull-up control bit 0: No pull-up 1: Pull-up 1 pull-up control bit 0: No pull-up 1: Pull-up P22 pull-up control bit 0: No pull-up 1: Pull-up P23 pull-up control bit 0: No pull-up 1: Pull-up 4 pull-up control bit 0: No pull-up 1: Pull-up P25 pull-up control bit 0: No pull-up 1: Pull-up 6 pull-up control bit 0: No pull-up 1: Pull-up P27 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected. b7 b0 Port P3 pull-up control register (PULL3: address 0FF316) P30 pull-up control bit 0: No pull-up 1: Pull-up 1 pull-up control bit 0: No pull-up 1: Pull-up Not used (return “0” when read) P34 pull-up control bit 0: No pull-up 1: Pull-up 5 pull-up control bit 0: No pull-up 1: Pull-up P36 pull-up control bit 0: No pull-up 1: Pull-up 7 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected.
Rev.1.00 Apr 2, 2007 Page 22 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 18. Structure of port pu ll-up control register (3) b7 b0 Port P4 pull-up control register (PULL4: address 0FF416) P40 pull-up control bit 0: No pull-up 1: Pull-up P41 pull-up control bit 0: No pull-up 1: Pull-up 2 pull-up control bit 0: No pull-up 1: Pull-up P43 pull-up control bit 0: No pull-up 1: Pull-up 4 pull-up control bit 0: No pull-up 1: Pull-up P45 pull-up control bit 0: No pull-up 1: Pull-up 6 pull-up control bit 0: No pull-up 1: Pull-up 7 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected. b7 b0 Port P5 pull-up control register (PULL5: address 0FF516) P50 pull-up control bit 0: No pull-up 1: Pull-up P51 pull-up control bit 0: No pull-up 1: Pull-up 2 pull-up control bit 0: No pull-up 1: Pull-up P53 pull-up control bit 0: No pull-up 1: Pull-up 4 pull-up control bit 0: No pull-up 1: Pull-up P55 pull-up control bit 0: No pull-up 1: Pull-up P56 pull-up control bit 0: No pull-up 1: Pull-up 7 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected.
Rev.1.00 Apr 2, 2007 Page 23 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 19. Structure of port pu ll-up control register (4) b7 b0 Port P6 pull-up control register (PULL6: address 0FF616) P60 pull-up control bit 0: No pull-up 1: Pull-up P61 pull-up control bit 0: No pull-up 1: Pull-up 2 pull-up control bit 0: No pull-up 1: Pull-up P63 pull-up control bit 0: No pull-up 1: Pull-up P64 pull-up control bit 0: No pull-up 1: Pull-up 5 pull-up control bit 0: No pull-up 1: Pull-up P66 pull-up control bit 0: No pull-up 1: Pull-up P67 pull-up control bit 0: No pull-up 1: Pull-up Note: Pull-up control is valid when the corresponding bit of the port direction register is “0” (input). When that bit is “1” (output), pull-up cannot be set to the port of which pull-up is selected.
Rev.1.00 Apr 2, 2007 Page 24 of 117 REJ03B0212-0100 3803 Group (Spec.L) Termination of unused pins
- Termination of common pins I/O ports: Select an input port or an output port and follow each processing method. In addition, it is recommended that related registers be overwritten periodically to prevent malfunctions, etc. Output ports: Open. Input ports: If the input level become unstable, through current flow to an input circuit, and the power supply current may increase. Especially, when expe cting low consumption current (at STP or WIT instruction execution etc.), pull-up or pull-down input ports to prevent through current (builtin resistor can be used). We recommend processing unused pins through a resistor which can secure I OH(avg) or IOL(avg). Because, when an I/O port or a pin which have an output function is selected as an input port, it may operate as an output port by incorrect operation etc. Table 7 Termination of unused pins Pins Termination P0, P1, P2, P3, P4, P5, P6 • Set to the input mode and connect each to V CC or VSS through a resistor of 1 kΩ to 10 kΩ.
- Set to the output mode and open at “L” or “H” output state. VREF Connect to VCC or VSS (GND). AVSS Connect to VCC or VSS (GND). XOUT Open (only when using external clock)
Rev.1.00 Apr 2, 2007 Page 25 of 117 REJ03B0212-0100 3803 Group (Spec.L) INTERRUPTS The 3803 group (Spec.L) interrupts are vector interrupts with a fixed priority scheme, and ge nerated by 16 sources among 21 sources: 8 external, 12 internal, and 1 software. The interrupt sources, vector addresses (1), and interrupt priority are shown in Table 8. Each interrupt except the BRK instruction interrupt has the interrupt request bit and the interr upt enable bit. These bits and the interrupt disable flag (I flag) control the acceptance of interrupt requests. Figure 20 shows an interrupt control diagram. An interrupt requests is accept ed when all of the following conditions are satisfied: Though the interrupt priority is determined by hardware, priority processing can be performed by software using the above bits and flag. NOTES: 1. Vector addresses contain interrupt jump destination addresses. 2. Reset function in the same way as an interrupt with the highest priority. Table 8 Interrupt vector addresses and priority Interrupt Source Priority Vector Addresses(1) Interrupt Request Generating Conditions Remarks High Low Reset(2) 1F F F D 16 FFFC16 At reset Non-maskable INT0 2F F F B 16 FFFA16 At detection of either rising or falling edge of INT0 input External interrupt (active edge selectable) Timer Z At timer Z underflow INT 1 3 FFF9 16 FFF816 At detection of either rising or falling edge of INT1 input External interrupt (active edge selectable) Serial I/O1 reception 4 FFF7 16 FFF616 At completion of serial I/O1 data reception Valid when serial I/O1 is selected Serial I/O1 transmission
5 FFF5 16 FFF416 At completion of serial I/O1
transmission shift or when transmission buffer is empty Valid when serial I/O1 is selected Timer X 6 FFF3
16 FFF216 At timer X underflow
Timer Y 7 FFF1 16 FFF016 At timer Y underflow Timer 1 8 FFEF 16 FFEE16 At timer 1 underflow STP release timer underflow Timer 2 9 FFED 16 FFEC16 At timer 2 underflow CNTR0 10 FFEB 16 FFEA16 At detection of either rising or falling edge of CNTR0 input External interrupt (active edge selectable) CNTR1 11 FFE9 16 FFE816 At detection of either rising or falling edge of CNTR1 input External interrupt (active edge selectable) Serial I/O3 reception At completion of serial I/O3 data reception Valid when serial I/O3 is selected Serial I/O2 12 FFE7 16 FFE616 At completion of serial I/O2 data transmission or reception Valid when serial I/O2 is selected Timer Z At timer Z underflow INT2 13 FFE5 16 FFE416 At detection of either rising or falling edge of INT2 input External interrupt (active edge selectable) INT3 14 FFE3 16 FFE216 At detection of either rising or falling edge of INT3 input External interrupt (active edge selectable) INT4 15 FFE1 16 FFE016 At detection of either rising or falling edge of INT4 input External interrupt (active edge selectable) CNTR2 At detection of either rising or falling edge of CNTR2 input External interrupt (active edge selectable) A/D conversion 16 FFDF 16 FFDE16 At completion of A/D conversion Serial I/O3 transmission At completion of serial I/O3 transmission shift or when transmission buffer is empty Valid when serial I/O3 is selected BRK instruction 17 FFDD
16 FFDC16 At BRK instruction execution Non-maskable software interrupt
Rev.1.00 Apr 2, 2007 Page 26 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 20. Interrupt control diagram
- Interrupt Disable Flag The interrupt disable flag is as signed to bit 2 of the processor status register. This flag controls the acceptance of all interrupt requests except for the BRK instruction. When this flag is set to “1”, the acceptance of interrupt requests is disabled. When it is set to “0”, acceptance of interrupt requests is enabled. This flag is set to “1” with the SET instruction and set to “0” with the CLI instruction. When an interrupt request is accepted, the contents of the processor status register are pu shed onto the stack while the interrupt disable flag remaines set to “0”. Subsequently, this flag is automatically set to “1” and multiple interrupts are disabled. To use multiple interrupts, set this flag to “0” with the CLI instruction within the interrupt processing routine. The contents of the processor st atus register are popped off the stack with the RTI instruction.
- Interrupt Request Bits Once an interrupt request is generate d, the corresponding interrupt request bit is set to “1” and remaines “1” until the request is accepted. When the request is accepted, this bit is automatically set to “0”. Each interrupt request bit can be set to “0”, but cannot be set to “1”, by software.
- Interrupt Enable Bits The interrupt enable bits control the acceptance of the corresponding interrupt requests. When an interrupt enable bit is set to “0”, the acceptance of th e corresponding interrupt request is disabled. If an interrupt reque st occurs in this condition, the corresponding interrupt request bit is set to “1”, but the interrupt request is not accepted. When an interrupt enable bit is set to “1”, acceptance of the corresponding interrupt request is enabled. Each interrupt enable bit can be set to “0” or “1” by software. The interrupt enable bit for an unused interrupt should be set to “0”.
- Interrupt Source Selection Any of the following combinati ons can be selected by the interrupt source selection register (0039 16). 1. INT0 or timer Z 2. CNTR1 or Serial I/O3 reception 3. Serial I/O2 or timer Z 4. INT4 or CNTR2 5. A/D conversion or serial I/O3 transmission
- External Interrupt Pin Selection For external interrupts INT 0 and INT4, the INT0, INT4 interrupt switch bit in the interrupt edge selection register (bit 6 of address 003A 16) can be used to select INT 00 and INT 40 pin input or INT01 and INT41 pin input. Interrupt disable flag (I) Interrupt request Interrupt request bit Interrupt enable bit BRK instruction Reset
Rev.1.00 Apr 2, 2007 Page 27 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 21. Structure of interrupt-related registers Interrupt edge selection register (INTEDGE : address 003A16) INT0 interrupt edge selection bit INT1 interrupt edge selection bit Not used (returns “0” when read) INT2 interrupt edge selection bit INT3 interrupt edge selection bit INT4 interrupt edge selection bit INT0, INT4 interrupt switch bit 0 : INT00, INT40 interrupt 1 : INT01, INT41 interrupt Not used (returns “0” when read) 0 : Falling edge active 1 : Rising edge active Interrupt request register 1 (IREQ1 : address 003C16) INT0/Timer Z interrupt request bit INT1 interrupt request bit Serial I/O1 receive interrupt request bit Serial I/O1 transmit interrupt request bit Timer X interrupt request bit Timer Y interrupt request bit Timer 1 interrupt request bit Timer 2 interrupt request bit Interrupt request register 2 (IREQ2 : address 003D 16) CNTR0 interrupt request bit CNTR1/Serial I/O3 receive interrupt request bit Serial I/O2/Timer Z interrupt request bit INT 2 interrupt request bit INT3 interrupt request bit INT4/CNTR2 interrupt request bit AD converter/Serial I/O3 transmit interrupt request bit Not used (returns “0” when read) 0 : No interrupt request issued 1 : Interrupt request issued Interrupt control register 1 (ICON1 : address 003E 16) INT0/Timer Z interrupt enable bit INT1 interrupt enable bit Serial I/O1 receive interrupt enable bit Serial I/O1 transmit interrupt enable bit Timer X interrupt enable bit Timer Y interrupt enable bit Timer 1 interrupt enable bit Timer 2 interrupt enable bit Interrupt control register 2 (ICON2 : address 003F 16) b7 b0 b7 b0 b7 b0 b7 b0 0 : Falling edge active 1 : Rising edge active CNTR0 interrupt enable bit CNTR1/Serial I/O3 receive interrupt enable bit Serial I/O2/Timer Z interrupt enable bit INT 2 interrupt enable bit INT3 interrupt enable bit INT4/CNTR2 interrupt enable bit AD converter/Serial I/O3 transmit interrupt enable bit Not used (returns “0” when read) (Do not write “1”.) 0 : Interrupts disabled 1 : Interrupts enabled b7 b0 Interrupt source selection register (INTSEL : address 003916) INT0/Timer Z interrupt source selection bit 0 : INT0 interrupt 1 : Timer Z interrupt Serial I/O2/Timer Z interrupt source selection bit 0 : Serial I/O2 interrupt 1 : Timer Z interrupt Not used (Do not write “1”.) INT 4/CNTR2 interrupt source selection bit 0 : INT4 interrupt 1 : CNTR2 interrupt Not used (Do not write “1”.) CNTR 1/Serial I/O3 receive interrupt source selection bit 0 : CNTR1 interrupt 1 : Serial I/O3 receive interrupt AD converter/Serial I/O3 transmit interrupt source selection bit 0 : A/D converter interrupt 1 : Serial I/O3 transmit interrupt (Do not write “1” to these bits simultaneously.) b7 b0 0 : No interrupt request issued 1 : Interrupt request issued 0 : Interrupts disabled 1 : Interrupts enabled
Rev.1.00 Apr 2, 2007 Page 29 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 24. Timing of interrupt request generation, interrupt request bit, and interrupt acceptance (1) The interrupt request bit for an interrupt request generated during period 1 is set to “1” at timing point IR1. (2) The interrupt request bit for an interrupt request generated during period 2 is set to “1” at timing point IR1 or IR2. The timing point at which the bit is set to “1” varies depending on conditions. When two or more interrupt requests are generated during the period 2, each request bit may be set to “1” at timing point IR1 or IR2 separately. T1 T2 T3 : Interrupt acceptance timing points IR1 IR2 : Timings points at which the interrupt request bit is set to “1”. Note : Period 2 indicates the last φ cycle during one instruction cycle. IR1T2 SYNC IR2T3 Internal clock φ Instruction cycle Push onto stack Vector fetch Instruction cycle
Rev.1.00 Apr 2, 2007 Page 30 of 117 REJ03B0212-0100 3803 Group (Spec.L) TIMERS
- 8 - b i t T i m e r s The 3803 group (Spec.L) has four 8-bit timers: timer 1, timer 2, timer X, and timer Y. The timer 1 and timer 2 use one prescaler in common, and the timer X and timer Y use each prescaler. Those are 8-bit prescalers. Each of the timers and prescalers has a timer latch or a prescaler latch. The division ratio of each timer or prescaler is given by 1/(n + 1), where n is the value in the corresponding timer or prescaler latch. All timers are down-counters. When the timer reaches “00 16”, an underflow occurs at the next coun t pulse and the co ntents of the corresponding timer latch are reloaded into the timer and the count is continued. When th e timer underflows, the interrupt request bit corresponding to that timer is set to “1”.
- Timer divider The divider count source is switched by the main clock division ratio selection bits of CPU mode register (bits 7 and 6 at address 003B16). When these bits are “00” (high-speed mode) or “01” (middle-speed mode), X IN is selected. When these bits are “10” (low-speed mode), XCIN is selected.
- Prescaler 12 The prescaler 12 counts the output of the timer divider. The count source is selected by the timer 12, X count source selection 1/512, 1/1024 of f(XIN) or f(XCIN).
- Timer 1 and Timer 2 The timer 1 and timer 2 counts the output of prescaler 12 and periodically set the interrupt request bit.
- Prescaler X and prescaler Y The prescaler X and prescaler Y count the output of the timer divider or f(XCIN). The count source is selected by the timer 12, X count source selection register (address 000E16) and the timer Y, Z count source selection register (address 000F16) among 1/2, f(XIN) or f(XCIN); and f(XCIN).
- Timer X and Timer Y The timer X and timer Y can each select one of four operating modes by setting the timer XY mode register (address 002316). (1) Timer mode
- Mode selection This mode can be selected by setting “00” to the timer X operating mode bits (bits 1 a nd 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316).
- Explanation of operation The timer count operation is started by setting “0” to the timer X count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the timer XY mode register (address 002316). When the timer reaches “00 16”, an underflow occurs at the next count pulse and the contents of timer latch are reloaded into the timer and the count is continued. (2) Pulse Output Mode
- Mode selection This mode can be selected by setting “01” to the timer X operating mode bits (bits 1 a nd 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316).
- Explanation of operation The operation is the same as the timer mode’s. Moreover the pulse which is inverted each time the timer underflows is output from CNTR 0/CNTR1 pin. Regardless of the timer counting or not the output of CNTR0/CNTR1 pin is initialized to the level of specified by their active edge sw itch bits when writing to the timer. When the CNTR 0 active edge switch bit (bit 2) and the CNTR 1 active edge switch bit (bit 6) of the timer XY mode register (address 002316) is “0”, the output starts with “H” level. When it is “1”, the output starts with “L” level. Switching the CNTR 0 or CNTR 1 active edge switch bit will reverse the output level of the corresponding CNTR 0 or CNTR1 pin.
- Precautions Set the double-function port of CNTR 0/CNTR 1 pin and port P54/P55 to output in this mode. (3) Event Counter Mode
- Mode selection This mode can be selected by setting “10” to the timer X operating mode bits (bits 1 a nd 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 0023 16).
- Explanation of operation The operation is the same as the timer mode’s except that the timer counts signals input from the CNTR 0 or CNTR1 pin. The valid edge for the count operation depends on the CNTR 0 active edge switch bit (bit 2) or the CNTR1 active edge switch bit (bit 6) of the timer XY mode register (address 0023 16). When it is “0”, the rising edge is valid. When it is “1”, the falling edge is valid.
- Precautions Set the double-function port of CNTR 0/CNTR 1 pin and port P54/P55 to input in this mode.
Rev.1.00 Apr 2, 2007 Page 31 of 117 REJ03B0212-0100 3803 Group (Spec.L) (4) Pulse Width Measurement Mode
- Mode selection This mode can be selected by setting “11” to the timer X operating mode bits (bits 1 a nd 0) and the timer Y operating mode bits (bits 5 and 4) of the timer XY mode register (address 002316).
- Explanation of operation When the CNTR 0 active edge switch b it (bit 2) or the CNTR 1 active edge switch bit (bit 6) of the timer XY mode register (address 002316) is “1”, the timer counts during the term of one falling edge of CNTR 0/CNTR1 pin input until the next rising edge of input (“L” term). When it is “0”, the timer counts during the term of one rising edge input until the next falling edge input (“H” term).
- Precautions Set the double-function port of CNTR 0/CNTR 1 pin and port P54/P55 to input in this mode. The count operation can be stopped by setting “1” to the timer X count stop bit (bit 3) and the timer Y count stop bit (bit 7) of the timer XY mode register (address 0023 16). The interrupt request bit is set to “1” each time the timer underflows.
- Precautions when switching count source When switching the count source by the timer 12, X and Y count source selection bits, the value of timer count is altered in inconsiderable amount owing to ge nerating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer.
Rev.1.00 Apr 2, 2007 Page 32 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 25. Block diagram of timer X, timer Y, timer 1, and timer 2 Q Q “1” “0” P54/CNTR0 Q Q P55/CNTR1 “0” “1” R R “1” “0” “0” “1” T T Prescaler X latch (8) Prescaler X (8) Timer X latch (8) Timer X (8) To timer X interrupt request bit Toggle flip-flop Timer X count stop bit Pulse width measurement mode Event counter mode To CNTR 0 interrupt request bit Pulse output mode Port P54 latchPort P54 direction register CNTR0 active edge switch bit Timer X latch write pulse Pulse output mode Timer mode Pulse output mode Prescaler Y latch (8) Prescaler Y (8) Timer Y latch (8) Timer Y (8) To timer Y interrupt request bit Toggle flip-flop Timer Y count stop bit To CNTR1 interrupt request bit Pulse output mode Port P55 latchPort P55 direction register CNTR1 active edge switch bit Timer Y latch write pulse Pulse output mode Timer mode Pulse output mode Prescaler 12 latch (8) Prescaler 12 (8) Timer 1 latch (8) Timer 1 (8) Timer 2 latch (8) Timer 2 (8) To timer 2 interrupt request bit To timer 1 interrupt request bit CNTR0 active edge switch bit CNTR1 active edge switch bit Pulse width measurement mode Event counter mode Clock for timer 12 Data bus Data bus Data bus Clock for timer 12 Divider Clock for timer Y Count source selection bit Main clock division ratio selection bits “00” “11” “10” XCIN Clock for timer X f(XCIN) Count source selection bit f(XCIN) Clock for timer Y
Rev.1.00 Apr 2, 2007 Page 33 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 26. Structure of timer XY mode register Timer XY mode register (TM : address 002316) Timer X operating mode bits b1 b0 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR 0 active edge switch bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer X count stop bit 0: Count start 1: Count stop Timer Y operating mode bits b5 b4 0 0: Timer mode 0 1: Pulse output mode 1 0: Event counter mode 1 1: Pulse width measurement mode CNTR 1 active edge switch bit 0: Interrupt at falling edge Count at rising edge in event counter mode 1: Interrupt at rising edge Count at falling edge in event counter mode Timer Y count stop bit 0: Count start 1: Count stop
Rev.1.00 Apr 2, 2007 Page 34 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 27. Structure of timer 12, X and time r Y, Z count source selection registers b7 b0 Timer 12, X count source selection register (T12XCSS : address 000E16) Timer 12 count source selection bits b3 b2 b1 b0 0 000 : f ( X IN)/2 or f(XCIN)/2 0 001 : f ( X IN)/4 or f(XCIN)/4 0 0 1 0 : f(X IN)/8 or f(XCIN)/8 0 0 1 1 : f(X IN)/16 or f(XCIN)/16 0 1 0 0 : f(X IN)/32 or f(XCIN)/32 0 1 0 1 : f(X IN)/64 or f(XCIN)/64 0 1 1 0 : f(X IN)/128 or f(XCIN)/128 0 1 1 1 : f(X IN)/256 or f(XCIN)/256 1 0 0 0 : f(X IN)/512 or f(XCIN)/512 1 0 0 1 : f(X IN)/1024 or f(XCIN)/1024 1 0 1 0 : 1 0 1 1 : 1 1 0 0 : 1 1 0 1 : 1 1 1 0 : 1 1 1 1 : Not used Timer X count source selection bits b7 b6 b5 b4 0 000 : f ( X IN)/2 or f(XCIN)/2 0 001 : f ( X IN)/4 or f(XCIN)/4 0 0 1 0 : f(X IN)/8 or f(XCIN)/8 0 0 1 1 : f(X IN)/16 or f(XCIN)/16 0 1 0 0 : f(X IN)/32 or f(XCIN)/32 0 1 0 1 : f(X IN)/64 or f(XCIN)/64 0 1 1 0 : f(X IN)/128 or f(XCIN)/128 0 1 1 1 : f(X IN)/256 or f(XCIN)/256 1 0 0 0 : f(X IN)/512 or f(XCIN)/512 1 0 0 1 : f(X IN)/1024 or f(XCIN)/1024 1 0 1 0 : f(X CIN) 1 0 1 1 : 1 1 0 0 : 1 1 0 1 : 1 1 1 0 : 1 1 1 1 : Not used b7 b0 Timer Y, Z count source selection register (TYZCSS : address 000F16) Timer Y count source selection bits b3 b2 b1 b0 0 000 : f ( X IN)/2 or f(XCIN)/2 0 001 : f ( X IN)/4 or f(XCIN)/4 0 0 1 0 : f(X IN)/8 or f(XCIN)/8 0 0 1 1 : f(X IN)/16 or f(XCIN)/16 0 1 0 0 : f(X IN)/32 or f(XCIN)/32 0 1 0 1 : f(X IN)/64 or f(XCIN)/64 0 1 1 0 : f(X IN)/128 or f(XCIN)/128 0 1 1 1 : f(X IN)/256 or f(XCIN)/256 1 0 0 0 : f(X IN)/512 or f(XCIN)/512 1 0 0 1 : f(X IN)/1024 or f(XCIN)/1024 1 0 1 0 : f(X CIN) Timer Z count source selection bits b7 b6 b5 b4 0 000 : f ( X IN)/2 or f(XCIN)/2 0 001 : f ( X IN)/4 or f(XCIN)/4 0 0 1 0 : f(X IN)/8 or f(XCIN)/8 0 0 1 1 : f(X IN)/16 or f(XCIN)/16 0 1 0 0 : f(X IN)/32 or f(XCIN)/32 0 1 0 1 : f(X IN)/64 or f(XCIN)/64 0 1 1 0 : f(X IN)/128 or f(XCIN)/128 0 1 1 1 : f(X IN)/256 or f(XCIN)/256 1 0 0 0 : f(X IN)/512 or f(XCIN)/512 1 0 0 1 : f(X IN)/1024 or f(XCIN)/1024 1 0 1 0 : f(X CIN) 1 0 1 1 : 1 1 0 0 : 1 1 0 1 : 1 1 1 0 : 1 1 1 1 : Not used 1 0 1 1 : 1 1 0 0 : 1 1 0 1 : 1 1 1 0 : 1 1 1 1 : Not used
Rev.1.00 Apr 2, 2007 Page 38 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 28. Block diagram of timer Z P47/SRDY2/ CNTR2 “001” XIN Output level latch Programmable one-shot generating mode CNTR2 active edge switch bit Programmable one-shot generating mode Data bus To timer Z interrupt request bit To INT1 interrupt request bitProgrammable waveform generating mode Pulse output mode CNTR2 active edge switch bit Pulse output mode Timer Z operating mode bits Port P47 direction register Port P47 latch Pulse period measurement mode Pulse width measurement mode Timer Z count stop bit Count source selection bit Divider Clock for timer z CNTR2 active edge switch bit D Q T “1” Timer/Event counter mode switch bit “0” “1” “1” “0” P42/INT1 Programmable one-shot generating circuit T Q S Q “100” “101” To CNTR2 interrupt request bit “0” f(XCIN) Edge detection circuit “1” “0” Timer Z low-order latch Timer Z low-order Timer Z high-order latch Timer Z high-order XCIN
Rev.1.00 Apr 2, 2007 Page 39 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 29. Structure of timer Z mode register b7 b0 Timer Z mode register (TZM : address 002A16) Timer Z operating mode bits b2 b1 b0 0 0 0 : Timer/Event counter mode 0 0 1 : Pulse output mode 0 1 0 : Pulse period measurement mode 0 1 1 : Pulse width measurement mode 1 0 0 : Programmable waveform generating mode 1 0 1 : Programmable one-shot generating mode 1 1 0 : Not available 1 1 1 : Not available Timer Z write control bit 0 : Writing data to both latch and timer simultaneously 1 : Writing data only to latch Output level latch 0 : “L” output 1 : “H” output CNTR 2 active edge switch bit 0 : •Event counter mode: Count at rising edge
- Pulse output mode: Start outputting “H”
- Pulse period measurement mode: Measurement between two falling edges
- Pulse width measurement mode: Measurement of “H” term
- Programmable one-shot generating mode: After start outputting “L”, “H” one-shot pulse generated
- Interrupt at falling edge 1 : •Event counter mode: Count at falling edge
- Pulse output mode: Start outputting “L”
- Pulse period measurement mode: Measurement between two rising edges
- Pulse width measurement mode: Measurement of “L” term
- Programmable one-shot generating mode: After start outputting “H”, “L” one-shot pulse generated
- Interrupt at rising edge Timer Z count stop bit 0 : Count start 1 : Count stop Timer/Event counter mode switch bit(1) 0 : Timer mode 1 : Event counter mode Note 1: When selecting the modes except the timer/event counter mode, set “0” to this bit.
Rev.1.00 Apr 2, 2007 Page 40 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 30. Timing chart of timer/event counter mode Fig 31. Timing chart of pulse output mode FFFF16 000016 TL TR TR TR TL : Value set to timer latch TR : Timer interrupt request TR TR TR TR Waveform output from CNTR2 pin CNTR2 CNTR2 FFFF16 000016 TL TL : Value set to timer latch TR : Timer interrupt request CNTR2 : CNTR2 interrupt request (CNTR2 active edge switch bit = “0”; Falling edge active)
Rev.1.00 Apr 2, 2007 Page 41 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 32. Timing chart of pulse period measurement mode (Measuring term between two rising edges) Fig 33. Timing chart of pulse width measurement mode (Measuring “L” term) TR TR T2 T3 CNTR2 of rising edge active TR : Timer interrupt request CNTR2 : CNTR2 interrupt request Signal input from CNTR2 pin CNTR2 FFFF16 000016 CNTR2 CNTR2 CNTR2 FFFF16FFFF16 + T1 TR T1T3 CNTR2 interrupt of rising edge active; Measurement of “L” width TR : Timer interrupt request CNTR2 : CNTR2 interrupt request Signal input from CNTR2 pin CNTR2 FFFF16 000016 CNTR2 CNTR2 FFFF16 + T2
Rev.1.00 Apr 2, 2007 Page 42 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 34. Timing chart of programmable waveform generating mode Fig 35. Timing chart of programmable one-shot generating mode (“H” one-shot pulse generating) Signal output from CNTR2 pin FFFF16 000016 T2T3 L L T1 TR TR TR TR CNTR2 CNTR2 L : Timer initial value TR : Timer interrupt request CNTR2 : CNTR2 interrupt request (CNTR2 active edge switch bit = “0”; Falling edge active) L TR TR TR L L Signal input from INT1 pin FFFF16 L CNTR2 CNTR2 L : One-shot pulse width TR : Timer interrupt request CNTR 2 : CNTR2 interrupt request (CNTR2 active edge switch bit = “0”; Falling edge active) Signal output from CNTR2 pin
Rev.1.00 Apr 2, 2007 Page 43 of 117 REJ03B0212-0100 3803 Group (Spec.L) SERIAL INTERFACE
- Serial I/O1 Serial I/O1 can be used as either clock synchronous or asynchronous (UART) serial I/O. A dedicated timer is also provided for baud rate generation. (1) Clock Synchronous Serial I/O Mode Clock synchronous serial I/O1 mode can be selected by setting the serial I/O1 mode selection bit of the serial I/O1 control register (bit 6 of address 001A16) to “1”. For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the transmit/receive buffer register. Fig 36. Block diagram of clock synchronous serial I/O1 Fig 37. Operation of clock synchronous serial I/O1 Serial I/O1 control register Receive buffer register 1 Receive shift register 1 Clock control circuit 1/4Baud rate generator 1f(XIN) Clock control circuitFalling-edge detector Transmit buffer register 1 Transmit shift register 1 Serial I/O1 status register F/F Address 001816 Receive buffer full flag (RBF) Receive interrupt request (RI) Shift clock Serial I/O1 synchronous clock selection bit Frequency division ratio 1/(n+1) Address 001C16 BRG count source selection bit Address 001816 Shift clock Transmit shift completion flag (TSC) Transmit buffer empty flag (TBE) Transmit interrupt request (TI) Transmit interrupt source selection bit Address 001916 Address 001A16 Data bus Data bus P46/SCLK1 P44/RXD1 P45/TXD1 P47/SRDY1/CNTR2 (f(XCIN) in low-speed mode) D0 D1 D2 D3 D4 D5 D6 D0 D1 D2 D3 D4 D5 D6 RBF = 1 TSC = 1TBE = 0 TBE = 1 TSC = 0 Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output T XD1 Serial input RXD1 Write pulse to receive/transmit buffer register 1 (address 001816) Overrun error (OE) detection Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TXD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1”. Receive enable signal SRDY1
Rev.1.00 Apr 2, 2007 Page 44 of 117 REJ03B0212-0100 3803 Group (Spec.L) (2) Asynchronous Serial I/O (UART) Mode Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O1 mode selection bit (b6) of the serial I/O1 control register to “0”. Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift re gisters each have a buffer, but the two buffers have the same address in a memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive bu ffer register can hold a character while the next character is being received. Fig 38. Block diagram of UART serial I/O1 Fig 39. Operation of UART serial I/O1 f(XIN) OE PE FE Data bus Data bus Receive buffer register 1 Address 001816 Receive shift register 1 Receive buffer full flag (RBF) Receive interrupt request (RI) Baud rate generator Frequency division ratio 1/(n+1) Address 001C16 ST/SP/PA generator Transmit buffer register 1 Transmit shift register 1 Address 001816 Transmit shift completion flag (TSC) Transmit buffer empty flag (TBE) Transmit interrupt request (TI) Address 001916 ST detector SP detector UART1 control register Address 001B16 Character length selection bit Address 001A16 BRG count source selection bit Transmit interrupt source selection bit Serial I/O1 synchronous clock selection bit Clock control circuit Character length selection bit 7 bits 8 bits Serial I/O1 status register Serial I/O1 control register P46/SCLK1 P44/RXD1 P45/TXD1 (f(XCIN) in low-speed mode) TSC=0 TBE=1 RBF=0 TBE=0 TBE=0 RBF=1 RBF=1 TBE=1 TSC=1* STD0 D1 SP D 0 D1ST SP Transmit or receive clock Transmit buffer write signal Serial output TXD1 Receive buffer read signal Serial input RXD1 Generated at 2nd bit in 2-stop-bit mode1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s) Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1”, can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O1 control register. 3: The receive interrupt (RI) is set when the RBF flag becomes “1”. 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0. STD0 D1 SP D 0 D1ST SP
Rev.1.00 Apr 2, 2007 Page 45 of 117 REJ03B0212-0100 3803 Group (Spec.L) [Transmit Buffer Register 1/Receive Buffer Register 1 (TB1/RB1)] 001816 The transmit buffer register 1 and the receive buffer register 1 are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is “0”. [Serial I/O1 Status Register (SIO1STS)] 0019 The read-only serial I/O1 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O1 function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to “0” when the receive buffer register is read. If there is an error, it is detect ed at the same time that data is transferred from the receive shif t register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O1 status register clea rs all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing “0” to the serial I/O1 enable bit SIOE (bit 7 of the serial I/O1 control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O1 status register are initialized to “0” at reset, but if the transmit enable bit (bit 4) of the serial I/O1 control register has been set to “1”, the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become “1”. [Serial I/O1 Control Register (SIO1CON)] 001A The serial I/O1 control register c onsists of eight control bits for the serial I/O1 function. [UART1 Control Register (UART1CON)] 001B16 The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchro nous serial I/O is selected and set the data format of an data transfer, and one bit (bit 4) which is always valid and sets the output structure of the P45/TXD1 pin. [Baud Rate Generator 1 (BRG1)] 001C16 The baud rate generator determin es the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.00 Apr 2, 2007 Page 46 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 40. Structure of serial I/O1 control registers Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns “1” when read) UART1 control register (UART1CON : address 001B 16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits 5/TXD1 P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return “1” when read) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN) in low-speed mode) 1: f(XIN)/4 (f(XCIN)/4 in low-speed mode) Serial I/O1 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O1 is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O1 is selected, external clock input divided by 16 when UART is selected. S RDY1 output enable bit (SRDY) 0: P47 pin operates as normal I/O pin 1: P47 pin operates as SRDY1 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O1 mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O1 enable bit (SIOE) 0: Serial I/O1 disabled (pins P4 4 to P47 operate as normal I/O pins) 1: Serial I/O1 enabled (pins P4 4 to P47 operate as serial I/O1 pins) Serial I/O1 control register (SIO1CON : address 001A16) Serial I/O1 status register (SIO1STS : address 001916) b0 b7 b0 b7 b0
Rev.1.00 Apr 2, 2007 Page 47 of 117 REJ03B0212-0100 3803 Group (Spec.L) <Notes concerning serial I/O1> 1. Notes when selecting clock synchronous serial I/O
1.1 Stop of transmission operation
- N o t e Clear the serial I/O1 enable b it and the transmit enable bit to “0” (serial I/O and transmit disabled).
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD1, R XD1, SCLK1 , and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD1 pin and an operation failure occurs.
1.2 Stop of receive operation
- N o t e Clear the receive enable bit to “0” (receive disabled), or clear the serial I/O1 enable bit to “0” (serial I/O disabled).
1.3 Stop of transmit/receive operation
- Note Clear both the transmit enable bit and receive enable bit to “0” (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.)
- R e a s o n In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to “0” (transmit disabled). Also, th e transmission circuit is not initialized by clearing the serial I/O1 enable bit to “0” (serial I/O disabled) (refer to 1.1). 2. Notes when selecting clock asynchronous serial I/O
2.1 Stop of transmission operation
- N o t e Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/O1 enable bit to “0”.
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD1, R XD1, SCLK1 , and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD1 pin and an operation failure occurs.
2.2 Stop of receive operation
- N o t e Clear the receive enable bit to “0” (receive disabled).
2.3 Stop of transmit/receive operation
- Note 1 (only transmission operation is stopped) Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/O1 enable bit to “0”.
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O1 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD1, R XD1, SCLK1 , and SRDY1 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O1 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD1 pin and an operation failure occurs.
- Note 2 (only receive operation is stopped) Clear the receive enable bit to “0” (receive disabled).
Rev.1.00 Apr 2, 2007 Page 48 of 117 REJ03B0212-0100 3803 Group (Spec.L) 3. SRDY1 output of reception side
- N o t e When signals are output from the S RDY1 pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the S RDY1 output enable bit, and the transmit enable bit to “1” (transmit enabled). 4. Setting serial I/O1 control register again
- N o t e Set the serial I/O1 control register again after the transmission and the reception circuits ar e reset by clearing both the transmit enable bit and the receive enable bit to “0”. 5.Data transmission control with referring to transmit shift register completion flag
- Note After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from “1” to “0” with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. 6. Transmission control when external clock is selected
- N o t e When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to “1” at “H” of the S CLK1 input level. Also, write data to the transmit buffer register at “H” of the SCLK1 input level. 7. Transmit interrupt request when transmit enable bit is set
- N o t e When using the transmit in terrupt, take the following sequence. 1. Set the serial I/O1 transmit interrupt enable bit to “0” (dis- abled). 2. Set the transmit enable bit to “1”. 3. Set the serial I/O1 transmit interrupt request bit to “0” after 1 or more instruction has executed. 4. Set the serial I/O1 transmit interrupt enable bit to “1” (enabled).
- R e a s o n When the transmit enable bit is set to “1”, the transmit buffer empty flag and the transmit shift register shift completion flag are also set to “1”. Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point. Clear both the transmit enable bit (TE) and the receive enable bit (RE) to “0” Set the bits 0 to 3 and bit 6 of the serial I/O1 control register Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to “1” Can be set with the LDM instruction at the same time
Rev.1.00 Apr 2, 2007 Page 49 of 117 REJ03B0212-0100 3803 Group (Spec.L)
- Serial I/O2 The serial I/O2 function can be used only for clock synchronous serial I/O. For clock synchronous serial I/ O2, the transmitter and the receiver must use the same clock. If the internal clock is used, transfer is started by a write signal to the serial I/O2 register (address 001F 16). [Serial I/O2 Control Register (SIO2CON)] 001D16 The serial I/O2 control register contains eight bits which control various serial I/O2 functions. Fig 41. Structure of Serial I/O2 control register Fig 42. Block diagram of serial I/O2 Serial I/O2 control register (SIO2CON : address 001D16) Internal synchronous clock selection bits b2 b1 b0 00 0 : f ( X IN)/8 (f(XCIN)/8 in low-speed mode) 00 1 : f ( X IN)/16 (f(XCIN)/16 in low-speed mode) 01 0 : f ( X IN)/32 (f(XCIN)/32 in low-speed mode) 01 1 : f ( X IN)/64 (f(XCIN)/64 in low-speed mode) 11 0 : f ( X IN)/128 f(XCIN)/128 in low-speed mode) 11 1 : f ( X IN)/256 (f(XCIN)/256 in low-speed mode) Serial I/O2 port selection bit 0: I/O port 1: SOUT2, SCLK2 signal output SRDY2 output enable bit 0: I/O port 1: SRDY2 signal output Transfer direction selection bit 0: LSB first 1: MSB first Serial I/O2 synchronous clock selection bit 0: External clock 1: Internal clock 1/SOUT2 P-channel output disable bit 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) f(XIN) Serial I/O counter 2 (3) Serial I/O2 register (8) Synchronization circuit “1” “0” “0” “1” “0” “1” SCLK2 “0” “1” Divider Data bus Serial I/O2 interrupt request Serial I/O2 port selection bit Serial I/O2 port selection bit Serial I/O2 synchronous clock selection bit SRDY2 output enable bit External clock Internal synchronous clock selection bits P52/SCLK2 P51/SOUT2 P50/SIN2 P52 latch P51 latch P53 latch P53/SRDY2 (f(XCIN) in low-speed mode) SRDY2 Address 001F16
Rev.1.00 Apr 2, 2007 Page 50 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 43. Timing of serial I/O2 D7D0 D1 D2 D3 D4 D5 D6 Transfer clock (1) Serial I/O2 output SOUT2 Serial I/O2 input SIN2 Receive enable signal SRDY2 Serial I/O2 register write signal (2) Serial I/O2 interrupt request bit set Notes1: When the internal clock is selected as the transfer clock, the divide ratio of f(XIN), or (f(XCIN) in low-speed mode, can be selected by setting bits 0 to 2 of the serial I/O2 control register. 2: When the internal clock is selected as the transfer clock, the SOUT2 pin goes to high impedance after transfer completion.
Rev.1.00 Apr 2, 2007 Page 51 of 117 REJ03B0212-0100 3803 Group (Spec.L)
- Serial I/O3 Serial I/O3 can be used as either clock synchronous or asynchronous (UART) serial I/O3. A dedicated timer is also provided for baud rate generation. (1) Clock Synchronous Serial I/O Mode Clock synchronous serial I/O3 mode can be selected by setting the serial I/O3 mode selection bit of the serial I/O3 control register (bit 6 of address 0032 16) to “1”. For clock synchronous serial I/O, the transmitter and the receiver must use the same clock. If an internal clock is used, transfer is started by a write signal to the transmit/receive buffer register. Fig 44. Block diagram of clock synchronous serial I/O3 Fig 45. Operation of clock synchronous serial I/O3 Serial I/O3 control register Receive buffer register 3 Receive shift register 3 Clock control circuit 1/4Baud rate generator 3f(XIN) Clock control circuitFalling-edge detector Transmit buffer register 3 Transmit shift register 3 Serial I/O3 status register F/F Address 003016 Receive buffer full flag (RBF) Receive interrupt request (RI) Shift clock Serial I/O3 synchronous clock selection bit Frequency division ratio 1/(n+1) Address 002F16 BRG count source selection bit Address 003016 Shift clock Transmit shift completion flag (TSC) Transmit buffer empty flag (TBE) Transmit interrupt request (TI) Transmit interrupt source selection bit Address 003116 Address 003216 Data bus Data bus P36/SCLK3 P34/RXD3 P35/TXD3 P37/SRDY3 (f(XCIN) in low-speed mode) D0 D1 D2 D3 D4 D5 D6 D0 D1 D2 D3 D4 D5 D6 RBF = 1 TSC = 1TBE = 0 TBE = 1 TSC = 0 Transfer shift clock (1/2 to 1/2048 of the internal clock, or an external clock) Serial output T XD3 Serial input RXD3 Write pulse to receive/transmit buffer register (address 003016) Overrun error (OE) detection Notes 1: As the transmit interrupt (TI), which can be selected, either when the transmit buffer has emptied (TBE=1) or after the transmit shift operation has ended (TSC=1), by setting the transmit interrupt source selection bit (TIC) of the serial I/O3 control register. 2: If data is written to the transmit buffer register when TSC=0, the transmit clock is generated continuously and serial data is output continuously from the TXD pin. 3: The receive interrupt (RI) is set when the receive buffer full flag (RBF) becomes “1”. Receive enable signal SRDY3
Rev.1.00 Apr 2, 2007 Page 52 of 117 REJ03B0212-0100 3803 Group (Spec.L) (2) Asynchronous Serial I/O (UART) Mode Clock asynchronous serial I/O mode (UART) can be selected by clearing the serial I/O3 mode selection bit (b6) of the serial I/O3 control register to “0”. Eight serial data transfer formats can be selected, and the transfer formats used by a transmitter and receiver must be identical. The transmit and receive shift re gisters each have a buffer, but the two buffers have the same address in a memory. Since the shift register cannot be written to or read from directly, transmit data is written to the transmit buffer register, and receive data is read from the receive buffer register. The transmit buffer register can also hold the next data to be transmitted, and the receive bu ffer register can hold a character while the next character is being received. Fig 46. Block diagram of UART serial I/O3 Fig 47. Operation of UART serial I/O3 f(XIN) OE PE FE Data bus Data bus Receive buffer register 3 Address 003016 Receive shift register 3 Receive buffer full flag (RBF) Receive interrupt request (RI) Baud rate generator 3 Frequency division ratio 1/(n+1) Address 002F16 ST/SP/PA generator Transmit buffer register 3 Transmit shift register 3 Address 003016 Transmit shift completion flag (TSC) Transmit buffer empty flag (TBE) Transmit interrupt request (TI) Address 003116 ST detector SP detector UART3 control register Address 003316 Character length selection bit Address 003216 BRG count source selection bit Transmit interrupt source selection bit Serial I/O3 synchronous clock selection bit Clock control circuit Character length selection bit 7 bits 8 bits Serial I/O3 status register Serial I/O3 control register P36/SCLK3 P34/RXD3 P35/TXD3 (f(XCIN) in low-speed mode) TSC=0 TBE=1 RBF=0 TBE=0 TBE=0 RBF=1 RBF=1 TBE=1 TSC=1* STD0 D1 SP D 0 D1ST SP Transmit or receive clock Transmit buffer write signal Serial output TXD3 Receive buffer read signal Serial input RXD3 * Generated at 2nd bit in 2-stop-bit mode1 start bit 7 or 8 data bit 1 or 0 parity bit 1 or 2 stop bit (s) Notes 1: Error flag detection occurs at the same time that the RBF flag becomes “1” (at 1st stop bit, during reception). 2: As the transmit interrupt (TI), when either the TBE or TSC flag becomes “1”, can be selected to occur depending on the setting of the transmit interrupt source selection bit (TIC) of the serial I/O3 control register. 3: The receive interrupt (RI) is set when the RBF flag becomes “1”. 4: After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle are necessary until changing to TSC=0. STD0 D1 SP D 0 D1ST SP
Rev.1.00 Apr 2, 2007 Page 53 of 117 REJ03B0212-0100 3803 Group (Spec.L) [Transmit Buffer Register 3/Receive Buffer Register 3 (TB3/RB3)] 003016 The transmit buffer register 3 and the receive buffer register 3 are located at the same address. The transmit buffer is write-only and the receive buffer is read-only. If a character bit length is 7 bits, the MSB of data stored in the receive buffer is “0”. [Serial I/O3 Status Register (SIO3STS)] 0031 The read-only serial I/O3 status register consists of seven flags (bits 0 to 6) which indicate the operating status of the serial I/O3 function and various errors. Three of the flags (bits 4 to 6) are valid only in UART mode. The receive buffer full flag (bit 1) is cleared to “0” when the receive buffer register is read. If there is an error, it is detect ed at the same time that data is transferred from the receive shif t register to the receive buffer register, and the receive buffer full flag is set. A write to the serial I/O3 status register clea rs all the error flags OE, PE, FE, and SE (bit 3 to bit 6, respectively). Writing “0” to the serial I/O3 enable bit SIOE (bit 7 of the serial I/O3 control register) also clears all the status flags, including the error flags. Bits 0 to 6 of the serial I/O3 status register are initialized to “0” at reset, but if the transmit enable bit (bit 4) of the serial I/O3 control register has been set to “1”, the transmit shift completion flag (bit 2) and the transmit buffer empty flag (bit 0) become “1”. [Serial I/O3 Control Register (SIO3CON)] 0032 The serial I/O3 control register c onsists of eight control bits for the serial I/O3 function. [UART3 Control Register (UART3CON)] 003316 The UART control register consists of four control bits (bits 0 to 3) which are valid when asynchro nous serial I/O is selected and set the data format of an data transfer, and one bit (bit 4) which is always valid and sets the output structure of the P35/TXD3 pin. [Baud Rate Generator 3 (BRG3)] 002F16 The baud rate generator determin es the baud rate for serial transfer. The baud rate generator divides the frequency of the count source by 1/(n + 1), where n is the value written to the baud rate generator.
Rev.1.00 Apr 2, 2007 Page 54 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 48. Structure of serial I/O3 control registers Transmit buffer empty flag (TBE) 0: Buffer full 1: Buffer empty Receive buffer full flag (RBF) 0: Buffer empty 1: Buffer full Transmit shift completion flag (TSC) 0: Transmit shift in progress 1: Transmit shift completed Overrun error flag (OE) 0: No error 1: Overrun error Parity error flag (PE) 0: No error 1: Parity error Framing error flag (FE) 0: No error 1: Framing error Summing error flag (SE) 0: (OE) U (PE) U (FE)=0 1: (OE) U (PE) U (FE)=1 Not used (returns “1” when read) UART3 control register (UART3CON : address 0033 16) Character length selection bit (CHAS) 0: 8 bits 1: 7 bits Parity enable bit (PARE) 0: Parity checking disabled 1: Parity checking enabled Parity selection bit (PARS) 0: Even parity 1: Odd parity Stop bit length selection bit (STPS) 0: 1 stop bit 1: 2 stop bits 5/TXD3 P-channel output disable bit (POFF) 0: CMOS output (in output mode) 1: N-channel open drain output (in output mode) Not used (return “1” when read) BRG count source selection bit (CSS) 0: f(XIN) (f(XCIN) in low-speed mode) 1: f(XIN)/4 (f(XCIN)/4 in low-speed mode) Serial I/O3 synchronous clock selection bit (SCS) 0: BRG output divided by 4 when clock synchronous serial I/O3 is selected, BRG output divided by 16 when UART is selected. 1: External clock input when clock synchronous serial I/O3 is selected, external clock input divided by 16 when UART is selected. S RDY3 output enable bit (SRDY) 0: P37 pin operates as normal I/O pin 1: P37 pin operates as SRDY3 output pin Transmit interrupt source selection bit (TIC) 0: Interrupt when transmit buffer has emptied 1: Interrupt when transmit shift operation is completed Transmit enable bit (TE) 0: Transmit disabled 1: Transmit enabled Receive enable bit (RE) 0: Receive disabled 1: Receive enabled Serial I/O3 mode selection bit (SIOM) 0: Clock asynchronous (UART) serial I/O 1: Clock synchronous serial I/O Serial I/O3 enable bit (SIOE) 0: Serial I/O3 disabled (pins P3 4 to P37 operate as normal I/O pins) 1: Serial I/O3 enabled (pins P3 4 to P37 operate as serial I/O3 pins) Serial I/O3 control register (SIO3CON : address 003216) Serial I/O3 status register (SIO3STS : address 003116) b0 b7 b0 b7 b0
Rev.1.00 Apr 2, 2007 Page 55 of 117 REJ03B0212-0100 3803 Group (Spec.L) <Notes concerning serial I/O3> 1. Notes when selecting clock synchronous serial I/O
- N o t e Clear the serial I/O3 enable b it and the transmit enable bit to “0” (serial I/O and transmit disabled).
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD3, R XD3, SCLK3 , and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD3 pin and an operation failure occurs.
- N o t e Clear the receive enable bit to “0” (receive disabled), or clear the serial I/O3 enable bit to “0” (serial I/O disabled).
- Note Clear both the transmit enable bit and receive enable bit to “0” (transmit and receive disabled). (when data is transmitted and received in the clock synchronous serial I/O mode, any one of data transmission and reception cannot be stopped.)
- R e a s o n In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to “0” (transmit disabled). Also, th e transmission circuit is not initialized by clearing the serial I/O3 enable bit to “0” (serial I/O disabled) (refer to 1.1). 2. Notes when selecting clock asynchronous serial I/O
- N o t e Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/O3 enable bit to “0”.
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD3, R XD3, SCLK3 , and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD3 pin and an operation failure occurs.
- N o t e Clear the receive enable bit to “0” (receive disabled).
- Note 1 (only transmission operation is stopped) Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/O3 enable bit to “0”.
- R e a s o n Since transmission is not stoppe d and the transmission circuit is not initialized even if only the serial I/O3 enable bit is cleared to “0” (serial I/O disabled), the internal transmission is running (in this case, since pins T XD3, R XD3, SCLK3 , and SRDY3 function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/O3 enable bit is set to “1” at this time, the data during internally shifting is output to the T XD3 pin and an operation failure occurs.
- Note 2 (only receive operation is stopped) Clear the receive enable bit to “0” (receive disabled).
Rev.1.00 Apr 2, 2007 Page 56 of 117 REJ03B0212-0100 3803 Group (Spec.L) 3. SRDY3 output of reception side
- N o t e When signals are output from the S RDY3 pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the S RDY3 output enable bit, and the transmit enable bit to “1” (transmit enabled). 4. Setting serial I/O3 control register again
- N o t e Set the serial I/O3 control register again after the transmission and the reception circuits ar e reset by clearing both the transmit enable bit and the receive enable bit to “0”. 5.Data transmission control with referring to transmit shift register completion flag
- N o t e After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from “1” to “0” with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. 6. Transmission control when external clock is selected
- N o t e When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to “1” at “H” of the S CLK3 input level. Also, write data to the transmit buffer register at “H” of the SCLK input level. 7. Transmit interrupt request when transmit enable bit is set
- N o t e When using the transmit in terrupt, take the following sequence. 1. Set the serial I/O3 transmit interrupt enable bit to “0” (dis- abled). 2. Set the transmit enable bit to “1”. 3. Set the serial I/O3 transmit interrupt request bit to “0” after 1 or more instruction has executed. 4. Set the serial I/O3 transmit interrupt enable bit to “1” (enabled).
- R e a s o n When the transmit enable bit is set to “1”, the transmit buffer empty flag and the transmit shift register shift completion flag are also set to “1”. Therefore, regardless of selecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point. Clear both the transmit enable bit (TE) and the receive enable bit (RE) to “0” Set the bits 0 to 3 and bit 6 of the serial I/O3 control register Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to “1” Can be set with the LDM instruction at the same time
Rev.1.00 Apr 2, 2007 Page 57 of 117 REJ03B0212-0100 3803 Group (Spec.L) PULSE WIDTH MODULATION (PWM) The 3803 group (Spec.H QzROM version) has PWM functions with an 8-bit resolution, based on a signal that is the clock input XIN or that clock input divided by 2 or the clock input X CIN or that clock input divided by 2 in low-speed mode.
- Data Setting The PWM output pin also functions as port P5 6. Set the PWM period by the PWM prescaler, and set the “H” term of output pulse by the PWM register. If the value in the PWM prescaler is n and the value in the PWM register is m (where n = 0 to 255 and m = 0 to 255): PWM period = 255 × (n+1) / f(X IN) (when f(XIN) = 8 MHz, count source selection bit = “0”) Output pulse “H” term = PWM period × m / 255 (when f(XIN) = 8 MHz, count source selection bit = “0”)
- PWM Operation When bit 0 (PWM enable bit) of the PWM control register is set to “1”, operation starts by initializing the PWM output circuit, and pulses are output starting at an “H”. If the PWM register or PWM pr escaler is updated during PWM output, the pulses will change in the cycle after the one in which the change was made. Fig 49. Timing of PWM period Fig 50. Block diagram of PWM function 31.875 × m × (n+1) 255 µs PWM output m : Contents of PWM register n : Contents of PWM prescaler T : PWM period (when f(XIN) = 8 MHz, count source selection bit = “0”) Data bus Count source selection bit “0” “1” PWM prescaler pre-latch PWM register pre-latch PWM prescaler latch PWM register latch Transfer control circuit PWM register XIN (XCIN at low- speed mode) Port P56 latch PWM function enable bit Port P56 PWM prescaler
Rev.1.00 Apr 2, 2007 Page 58 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 51. Structure of PWM control register Fig 52. PWM output timing when PWM register or PWM prescaler is changed <Notes> The PWM starts after the PWM function enable bit is set to enable and “L” level is output from the PWM pin. The length of this “L” level output is as follows: (Count source selection bit = 0, where n is the value set in the prescaler) (Count source selection bit = 1, where n is the value set in the prescaler) b7 b0 PWM control register (PWMCON: address 002B16) PWM function enable bit 0 : PWM disabled 1 : PWM enabled Count source selection bit 0:f ( XIN) (f(XCIN) at low-speed mode) 1:f ( XIN)/2 (f(XCIN)/2 at low-speed mode) Not used (return “0” when read) PWM output T T T2 B C PWM register write signal PWM prescaler write signal (Changes “H” term from “A” to “ B”.) (Changes PWM period from “T” to “T2”.) B T C T2= When the contents of the PWM register or PWM prescaler have changed, the PWM output will change from the next period after the change. A n1+ n1+
Rev.1.00 Apr 2, 2007 Page 59 of 117 REJ03B0212-0100 3803 Group (Spec.L) A/D CONVERTER (successive approximation type) [AD Conversion Register 1, 2 (AD1, AD2)] 0035 16, 003816 The AD conversion register is a read-only register that stores the result of an A/D conversion. When reading this register during an A/D conversion, the previous conversion result is read. Bit 7 of the AD conversion regi ster 2 is the conversion mode selection bit. When this bit is set to “0”, the A/D converter becomes the 10-bit A/D mode. When this bit is set to “1”, that becomes the 8-bit A/D mode. The conversion result of the 8-bit A/D mode is stored in the AD conversion register 1. As for 10-bit A/D mode, not only 10-bit reading but also only high-order 8-bit reading of conversion result can be performed by selecting the reading procedure of the AD conv ersion registers 1, 2 after A/D conversion is completed (in Figure 54). As for 10-bit A/D mode, the 8-bit reading inclined to MSB is performed when reading the AD co nverter register 1 after A/D conversion is started; and when the AD converter register 1 is read after reading the AD converter register 2, the 8-bit reading inclined to LSB is performed. [AD/DA Control Register (ADCON)] 0034 The AD/DA control register controls the A/D conversion process. Bits 0 to 2 and bit 4 se lect a specific analog input pin. Bit 3 signals the completion of an A/D conversion. The value of this bit remains at “0” during an A/D conversion, and changes to “1” when an A/D conversion ends. Writing “0” to this bit starts the A/D conversion.
- Comparison Voltage Generator The comparison voltage generato r divides the voltage between AVSS and V REF into 1024, and that outputs the comparison voltage in the 10-bit A/D mode (256 division in 8-bit A/D mode). The A/D converter successive ly compares the comparison voltage Vref in each mode, dividing the V REF voltage (see below), with the input voltage.
- 10-bit A/D mode (10-bit reading) Vref = × n (n = 0 − 1023)
- 10-bit A/D mode (8-bit reading) Vref = × n (n = 0 − 255)
- 8-bit A/D mode =0 (n = 0)
- Channel Selector The channel selector selects one of ports P67/AN7 to P60/AN0 or P07/AN15 to P00/AN8, and inputs the voltage to the comparator.
- Comparator and Control Circuit The comparator and control circ uit compares an analog input voltage with the comparison voltage, and then stores the result in the AD conversion registers 1, 2. When an A/D conversion is completed, the control circuit sets the AD conversion completion bit and the AD interrupt request bit to “1”. Note that because the comparator consists of a capacitor coupling, set f(X IN) to 500 kHz or more during an A/D conversion. Fig 53. Structure of AD/DA control register Fig 54. Structure of 10-bit A/D mode reading VREF VREF VREF AD/DA control register (ADCON : address 003416) Analog input pin selection bits 1 0 0 0: P6 0/AN0o r P00/AN8 0 0 1: P6 1/AN1o r P01/AN9 0 1 0: P6 2/AN2o r P02/AN10 0 1 1: P6 3/AN3o r P03/AN11 1 0 0: P6 4/AN4o r P04/AN12 1 0 1: P6 5/AN5o r P05/AN13 1 1 0: P6 6/AN6o r P06/AN14 1 1 1: P6 7/AN7o r P07/AN15 AD conversion completion bit 0: Conversion in progress 1: Conversion completed Analog input pin selection bit 2 0: AN 0 to AN7 side 1: AN8 to AN15 side Not used (returns “0” when read) DA1 output enable bit 0: DA1 output disabled 1: DA1 output enabled DA2 output enable bit 0: DA2 output disabled 1: DA2 output enabled b7 b0 b2 b1 b0 10-bit reading (Read address 003816 before 003516) AD conversion register 2 (AD2: address 003816) AD conversion register 1 (AD1: address 003516) Note : Bits 2 to 6 of address 003816 become “0” at reading. 8-bit reading (Read only address 003516) AD conversion register 1 (AD1: address 003516) b9 b7 b0 b8 b7 b6 b5 b4 b3 b2 b7 b0 b9 b8 b7 b0 b6 b5 b4 b3 b2 b1 b0
Rev.1.00 Apr 2, 2007 Page 60 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 55. Block diagram of A/D converter Channel selector A/D control circuit AD conversion register 1 Resistor ladder VREF AVSS Comparator A/D converter interrupt request P60/AN0 P61/AN1 P62/AN2 P63/AN3 P64/AN4 P65/AN5 P66/AN6 P67/AN7 P00/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 b7 b0 Data bus AD/DA control register (Address 003416) AD conversion register 2 (Address 003816) (Address 003516)
Rev.1.00 Apr 2, 2007 Page 61 of 117 REJ03B0212-0100 3803 Group (Spec.L) D/A CONVERTER The 3803 group (Spec.L) has two internal D/A converters (DA 1 and DA2) with 8-bit resolution. The D/A conversion is performed by setting the value in each DA conversion register. The result of D/A conversion is output from the DA1 or DA2 pin by setting the DA output enable bit to “1”. When using the D/A converter, th e corresponding port direction register bit (P3 0/DA1 or P3 1/DA2) must be set to “0” (input status). The output analog voltage V is determined by the value n (decimal notation) in the DA conversion register as follows: V = V REF × n/256 (n = 0 to 255) Where VREF is the reference voltage. At reset, the DA conversion re gisters are cleared to “00 16”, and the DA output enable bits ar e cleared to “0”, and the P3 0/DA1 and P31/DA2 pins become high impedance. The DA output does not have buffers. Accordingly, connect an external buffer when driving a low-impedance load. Fig 56. Block diagram of D/A converter Fig 57. Equivalent connection circuit of D/A converter (DA1) DA1 conversion register (8) DA1 output enable bit P30/DA1 Data bus R-2R resistor ladder DA2 conversion register (8) DA2 output enable bit P31/DA2R-2R resistor ladder DA1 output enable bit AVSS VREF R 2RRRRRRR 2R2R2R2R2R2R2R2R LSB “1”“0” MSB DA1 conversion register P30/DA1 “0” “1”
Rev.1.00 Apr 2, 2007 Page 62 of 117 REJ03B0212-0100 3803 Group (Spec.L) WATCHDOG TIMER The watchdog timer gives a mean of returning to the reset status when a program cannot run on a normal loop (for example, because of a software run-away). The watchdog timer consists of an 8-bit watchdog timer L and an 8-bit watchdog timer H.
- Watchdog Timer Initial Value Watchdog timer L is set to “FF16” and watchdog timer H is set to “FF16” by writing to the watchdog timer control register (address 001E16) or at a reset. Any write instruction that causes a write signal can be used, such as the STA, LDM, CLB, etc. Data can only be written to bits 6 and 7 of the watchdog timer control register. Regardless of the value written to bits 0 to 5, the above- mentioned value will be set to each timer. Bit 6 can be written only once after releasing reset. After rewriting it is disable to write any data to this bit.
- Watchdog Timer Operations The watchdog timer stops at rese t and starts to count down by writing to the watchdog timer control register (address 001E 16). An internal reset occurs at an underflow of the watchdog timer H. The reset is released after waiting for a reset release time and the program is processed from the reset vector address. Accordingly, programming is usua lly performed so that writing to the watchdog timer control register may be started before an underflow. If writing to the watchdog timer control register is not performed once, the watchdog timer does not function.
- Bit 6 of Watchdog Timer Control Register
- When bit 6 of the watchdog timer control register is “0”, the MCU enters the stop mode by ex ecution of STP instruction. Just after releasing the stop mode, the watchdog timer restarts counting (Note.) . When executing the WIT instruction, the watchdog timer does not stop.
- When bit 6 is “1”, execution of STP instruction causes an internal reset. When this bit is set to “1” once, it cannot be rewritten to “0” by program. Bit 6 is “0” at reset. The following shows the period between the write execution to the watchdog timer control register and the underflow of watchdog timer H. Bit 7 of the watchdog timer control register is “0”: when X CIN = 32.768 kHz; 32 s when XIN = 16 MHz; 65.536 ms Bit 7 of the watchdog timer control register is “1”: when XCIN = 32.768 kHz; 125 ms when XIN = 16 MHz; 256 µs Note. The watchdog timer continues to count even while waiting for a Fig 58. Block diagram of Watchdog timer Fig 59. Structure of Watchd og timer control register XIN Data bus XCIN “10” “00” “01” Main clock division ratio selection bits(1) “0” “1”1/16 Watchdog timer H count source selection bit Reset circuit STP instruction function selection bit Watchdog timer H (8) “FF16” is set when watchdog timer control register is written to.Internal reset Watchdog timer L (8) “FF16” is set when watchdog timer control register is written to. Note 1: Any one of high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. STP instruction RESET Watchdog timer H (for read-out of high-order 6 bit) STP instruction function selection bit 0: Entering stop mode by execution of STP instruction 1: Internal reset by execution of STP instruction Watchdog timer H count source selection bit 0: Watchdog timer L underflow 1: f(X IN)/16 or f(XCIN)/16 Watchdog timer control register (WDTCON : address 001E16)
Rev.1.00 Apr 2, 2007 Page 63 of 117 REJ03B0212-0100 3803 Group (Spec.L) RESET CIRCUIT To reset the microcomputer, RESET pin should be held at an “L” level for 16 cycles or more of X IN. Then the RESET pin is returned to an “H” level (the power source voltage should be between 1.8 V and 5.5 V (between 2.7 V to 5.5 V for flash memory version), and the oscillat ion should be stable), reset is released. After the reset is completed, the program starts from the address contained in address FFFD 16 (high-order byte) and address FFFC16 (low-order byte). Make sure that the reset input voltage for the mask ROM version is less than 0.29 V for VCC of 1.8 V. In the flash memory version, input to the RESET pin in the following procedure.
- When power source is stabilized (1) Input “L” level to RESET pin. (2) Input “L” level for 16 cycles or more to X IN pin. (3) Input “H” level to RESET pin.
- At power-on (1) Input “L” level to RESET pin. (2) Increase the power source voltage to 2.7 V. (3) Wait for td(P-R) until intern al power source has stabilized. (4) Input “L” level for 16 cycles or more to X IN pin. (5) Input “H” level to RESET pin. Fig 60. Reset circuit example Fig 61. Reset sequence VCCRESET VCCRESET Power source voltage detection circuit Example at VCC = 5 V (1) 0 V 0 V VCC RESET 0.2VCC or less 0 V 0 V VCC RESET td(P-R)+XIN16 cycles or more 5 V 5 V 2.7 V Notes 1: Reset release voltage
- mask ROM version: VCC = 1.8 V
- Flash memory version: VCC = 2.7 V 2: In the flash memory version, this time is required td(P-R)+XIN 16 cycles or more. (2) RESET Internal reset Data φ Address SYNC XIN ? ? ? ? FFFC FFFD AD H,L ? ? ? ?A D L ADH Notes 1: The frequency relation of f(XIN) and f(φ) is f(XIN) = 8 • f(φ). 2: The question marks (?) indicate an undefined state that depends on the previous state. Reset address from the vector table. XIN : 10.5 to 18.5 clock cycles
Rev.1.00 Apr 2, 2007 Page 64 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 62. Internal status at reset Note : X: Not fixed. Since the initial values for other than above mentioned registers and RAM contents are indefinite at reset, they must be set. Port P0 (P0) Port P0 direction register (P0D) Port P1 (P1) Port P1 direction register (P1D) Port P2 (P2) Port P2 direction register (P2D) Port P3 (P3) Port P3 direction register (P3D) Port P4 (P4) Port P4 direction register (P4D) Port P5 (P5) Port P5 direction register (P5D) Port P6 (P6) Port P6 direction register (P6D) Timer 12, X count source selection register (T12XCSS) Timer Y, Z count source selection register (TYZCSS) MISRG Transmit/Receive buffer register 1 (TB1/RB1) Serial I/O1 status register (SIO1STS) Serial I/O1 control register (SIO1CON) UART1 control register (UART1CON) Baud rate generator 1 (BRG1) Serial I/O2 control register (SIO2CON) Watchdog timer control register (WDTCON) Serial I/O2 register (SIO2) Prescaler 12 (PRE12) Timer 1 (T1) Timer 2 (T2) Timer XY mode register (TM) Prescaler X (PREX) Timer X (TX) Prescaler Y (PREY) Timer Y (TY) (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) (23) (24) (25) (26) (27) (28) (29) (30) (31) (32) (33) Register contentsAddress 0000 000116 000216 000316 000416 000516 000616 000716 000816 000916 000A16 000B16 000C16 000D16 000E16 000F16 001016 001816 001916 001A16 001B16 001C16 001D16 001E16 001F16 002016 002116 002216 002316 002416 002516 002616 002716 Timer Z (low-order) (TZL) Timer Z (high-order) (TZH) Timer Z mode register (TZM) PWM control register (PWMCON) PWM prescaler (PREPWM) PWM register (PWM) Baud rate generator 3 (BRG3) Transmit/Receive buffer register 3 (TB3/RB3) Serial I/O3 status register (SIO3STS) Serial I/O3 control register (SIO3CON) UART3 control register (UART3CON) AD/DA control register (ADCON) AD conversion register 1 (AD1) DA1 conversion register (DA1) DA2 conversion register (DA2) AD conversion register 2 (AD2) Interrupt source selection register (INTSEL) Interrupt edge selection register (INTEDGE) CPU mode register (CPUM) Interrupt request register 1 (IREQ1) Interrupt request register 2 (IREQ2) Interrupt control register 1 (ICON1) Interrupt control register 2 (ICON2) Flash memory control register 0 (FMCR0) Flash memory control register 1 (FMCR1) Flash memory control register 2 (FMCR2) Port P0 pull-up control register (PULL0) Port P1 pull-up control register (PULL1) Port P2 pull-up control register (PULL2) Port P3 pull-up control register (PULL3) Port P4 pull-up control register (PULL4) Port P5 pull-up control register (PULL5) Port P6 pull-up control register (PULL6) Processor status register Program counter (34) (35) (36) (37) (38) (39) (40) (41) (42) (43) (44) (45) (46) (47) (48) (49) (50) (51) (52) (53) (54) (55) (56) (57) (58) (59) (60) (61) (62) (63) (64) (65) (66) (67) (68) 0028 002916 002A16 002B16 002C16 002D16 002F16 003016 003116 003216 003316 003416 003516 003616 003716 003816 003916 003A16 003B16 003C16 003D16 003E16 003F16 0FE016 0FE016 0FE216 0FF016 0FF116 0FF216 0FF316 0FF416 0FF516 0FF616 (PS) (PCH) (PCL) Register contentsAddress 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 0016 FF16 0116 FF16 0016 0016 FF16 FF16 0016 FF16 FF16 0016 0016 0016 0016 0016 FF16 0016 0016 FF16 0016 0016 0016 0016 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0016 0016 0016 0016 FFFC16 contents FFFD16 contents 0016 0016 0016 XXX1XXXX 10000000 00000010 10010010
Rev.1.00 Apr 2, 2007 Page 65 of 117 REJ03B0212-0100 3803 Group (Spec.L) CLOCK GENERATING CIRCUIT The 3803 group (Spec.L) has two built-in oscillation circuits: main clock X IN-XOUT oscillation circuit and sub clock X CIN- XCOUT oscillation circuit. An oscillation circuit can be formed by connecting a resonator between X IN and X OUT (X CIN and XCOUT ). Use the circuit constants in accordance with the resonator manufacturer’s recommended values. No external resistor is needed between X IN and X OUT since a feed-back resistor exists on-chip.(An exte rnal feed-back resistor may be needed depending on conditions.) However, an external feed- back resistor is needed between XCIN and XCOUT. Immediately after power on, only the X IN oscillatio n circuit starts oscillating, and XCIN and XCOUT pins function as I/O ports.
- Frequency Control (1) Middle-speed mode The internal clock φ is the frequency of X IN divided by 8. After reset is released, this mode is selected. (2) High-speed mode The internal clock φ is half the frequency of XIN. (3) Low-speed mode The internal clock φ is half the frequency of XCIN. (4) Low power dissipation mode The low power consumption ope ration can be realized by stopping the main clock X IN in low-speed mode. To stop the main clock, set bit 5 of the CPU mode register to “1”. When the main clock XIN is restarted (by setting the main clock stop bit to “0”), set sufficient time for oscillation to stabilize. The sub-clock X CIN-XCOUT oscillating circuit can not directly input clocks that are generate d externally. Accordingly, make sure to cause an external resonator to oscillate. Oscillation Control (1) Stop mode If the STP instruction is executed, the internal clock φ stops at an “H” level, and X IN and X CIN oscillators stop. When the oscillation stabilizing time set after STP instruction released bit (bit 0 of address 0010 16) is “0”, the prescaler 12 is set to “FF16” and timer 1 is set to “0116”. When the oscillation stabilizing time set after STP instruction released bit is “1”, set the sufficient time for oscillation of used oscillator to stabilize since nothing is set to the prescaler 12 and timer 1. After STP instruction is released , the input of the prescaler 12 is connected to count source which had set at executing the STP instruction, and the output of the prescaler 12 is connected to timer 1. Oscillator restarts when an external interrupt is received, but the internal clock φ is not supplied to the CPU (remains at “H”) until timer 1 underfl ows. The internal clock φ is supplied for the first time, when timer 1 underflows. This ensures time for the clock oscillation using the ceramic resonators to be stabilized. When the oscillator is restarted by reset, apply “L” level to the RESET pin until the oscillation is stable since a wait time will not be generated. (2) Wait mode If the WIT instruction is executed, the internal clock φ stops at an “H” level, but the oscillator does not stop. The internal clock φ restarts at reset or when an interrupt is received. Since the oscillator does not stop, normal operation can be started immediately after the clock is restarted. To ensure that the interrupts will be received to release the STP or WIT state, their interrupt enable bits must be set to “1” before executing of the STP or WIT instruction. When releasing the STP state, the prescaler 12 and timer 1 will start counting the clock X IN divided by 16. Accordingly, set the timer 1 interrupt enable bit to “0” before executing the STP instruction. <Notes>
- If you switch the mode between middle/high-speed and low- speed, stabilize both XIN and XCIN oscillations. The sufficient time is required for the sub clock to stabilize, especially immediately after power on a nd at returning from stop mode. When switching the mode betw een middle/high-speed and low-speed, set the frequency on condition that f(X IN ) > 3×f(XCIN).
- When using the quartz-crystal oscillator of high frequency, such as 16 MHz etc., it may be necessary to select a specific oscillator with the specification demanded.
- When using the oscillation st abilizing time set after STP instruction released bit set to “1”, evaluate time to stabilize oscillation of the used oscillator and set the value to the timer 1 and prescaler 12.
Rev.1.00 Apr 2, 2007 Page 66 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 63. Ceramic resonator circuit Fig 64. External clock input circuit XCIN XCOUT XIN XOUT CIN COUTCCIN CCOUT Rf Rd Rd Note 1 : Insert a damping resistor if required. The resistance will vary depending on the oscillator and the oscillation drive capacity setting. Use the value recommended by the maker of the oscillator. Also, if the oscillator manufacturer’s data sheet specifies that a feedback resistor be added external to the chip though a feedback resistor exists on-chip, insert a feedback resistor between X IN and XOUT following the instruction. XIN XOUT External oscillation circuit VCC VSS Open XCIN XCOUT VCC VSS CCIN Rf Rd
Rev.1.00 Apr 2, 2007 Page 67 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 65. System clock generating circuit block diagram (Single-chip mode) WIT instruction STP instruction Timing φ (internal clock) S R QS R Q Main clock stop bit S R Q 1/2 1/4 XIN XOUT XCOUTXCIN Interrupt request Interrupt disable flag l Reset Port XC switch bit “1” “0” Low-speed mode High-speed or middle-speed mode Middle-speed mode High-speed or low-speed mode Main clock division ratio selection bits(1) Main clock division ratio selection bits (1) Notes1: Either high-speed, middle-speed or low-speed mode is selected by bits 7 and 6 of the CPU mode register. When low-speed mode is selected, set port XC switch bit (b4) to “1”. 2:f ( XIN)/16 is supplied as the count source to the prescaler 12 at reset, the count source before executing the STP instruction is supplied as the count source at executing STP instruction. 3: When bit 0 of MISRG is “0”, timer 1 is set “0116” and prescaler 12 is set “FF16” automatically. When bit 0 of MISRG is “1” , set the appropriate value to them in accordance with oscillation stabilizing time required by the using oscillator because nothing is automatically set into timer 1 and prescaler 12. 4: Although a feed-back resistor exists on-chip, an external feed-back resistor may be needed depending on conditions. Prescaler 12 Timer 1 Reset or STP instruction(2) Reset (3) (4) STP instruction Divider
Rev.1.00 Apr 2, 2007 Page 68 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 66. State transitions of system clock CM4 : Port XC switch bit 0 : I/O port function (stop oscillating) 1 : XCIN-XCOUT oscillating function CM5 : Main clock (XIN-XOUT) stop bit 0 : Operating 1 : Stopped CM7, CM6: Main clock division ratio selection bit b7 b6 00 : φ = f(XIN)/2 (High-speed mode) 01 : φ = f(XIN)/8 (Middle-speed mode) 10 : φ = f(XCIN)/2 (Low-speed mode) 1 1 : Not available ResetCM4 CM4 CM6 CM7 CM4 CM5 CM6 CM6 CPU mode register (CPUM : address 003B16) b7 b4 High-speed mode (f(φ) = 4 MHz) CM7=0 CM6=0 CM5=0 (8 MHz oscillating) CM4=0 (32 kHz stopped) High-speed mode (f(φ) = 4 MHz) CM7=0 CM6=0 CM5=0 (8 MHz oscillating) CM4=1 (32 kHz oscillating) Notes1: Switch the mode by the allows shown between the mode blocks. (Do not switch between the modes directly without an allow.) 2: The all modes can be switched to the stop mode or the wait mode and return to the source mode when the stop mode or the wait mode is ended. 3: Timer operates in the wait mode. 4: When the stop mode is ended, a delay of approximately 1 ms occurs by connecting prescaler 12 and Timer 1 in middle/high- speed mode. 5: When the stop mode is ended, a delay of approximately 0.25 s occurs by Timer 1 and Timer 2 in low-speed mode. 6: Wait until oscillation stabilizes after oscillating the main clock XIN before the switching from the low-speed mode to middle/ high-speed mode. 7: The example assumes that 8 MHz is being applied to the XIN pin and 32 kHz to the XCIN pin. φ indicates the internal clock. Middle-speed mode (f(φ) = 1 MHz) CM7=0 CM6=1 CM5=0 (8 MHz oscillating) CM4=0 (32 kHz stopped) Middle-speed mode (f(φ) = 1 MHz) CM7=0 CM6=1 CM5=0 (8 MHz oscillating) CM4=1 (32 kHz oscillating) Low-speed mode (f(φ) = 16 kHz) CM7=1 CM6=0 CM5=0 (8 MHz oscillating) CM4=1 (32 kHz oscillating) Low-speed mode (f(φ) = 16 kHz) CM7=1 CM6=0 CM5=1 (8 MHz stopped) CM4=1 (32 kHz oscillating)
Rev.1.00 Apr 2, 2007 Page 69 of 117 REJ03B0212-0100 3803 Group (Spec.L) FLASH MEMORY MODE The 3803 group (Spec.L)’s flash memory version has the flash memory that can be rewritten with a single power source. For this flash memory, three flash memory modes are available in which to read, program, an d erase: the parallel I/O and standard serial I/O modes in which the flash memory can be manipulated using a programmer and the CPU rewrite mode in which the flash memory can be manipulated by the Central Processing Unit (CPU). This flash memory version has some blocks on the flash memory as shown in Figure 67 and each block can be erased. In addition to the ordinary Us er ROM area to store the MCU operation control program, the fl ash memory has a Boot ROM area that is used to store a pr ogram to control rewriting in CPU rewrite and standard serial I/O modes. This Boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the factory. However, the user can write a rewrite control program in this area th at suits the user’s application system. This Boot ROM area can be rewritten in only parallel I/O mode. Summary Table 9 lists the summary of the 3803 group (Spec.L) flash memory version. NOTE: 1. The Boot ROM area has had a standard serial I/O mode cont rol program stored in it when shipped from the factory. This Boot ROM area can be erased and written in only parallel I/O mode. NOTES: 1. V CC = AVCC = 2.7 V to 5.5 V, Topr = 0 °C to 60 °C, unless otherwise noted. 2. Definition of programming/erase count The programming/erase count refers to the number of erase operations per block. For example, if block A is a 2 Kbyte block and 2,048 1-byte writes are performed, all to different addresses, after which block A is erased, the programming/erase count is 1. Note that for each erase operation it is not possible to perform more than one programming (write) operation to the same address (overwrites prohibited). 3. This is the number of times for which al l electrical characteristics are guaranteed after a programming or erase operation. (The guarantee covers the range from 1 to maximum value.) 4. On systems where reprogramming is performed a large number of ti mes, it is possible to reduce the effective number of overwrites by sequentially shifting the write address, so that as much of the available area of the block is used up through successive programming (write) operations before an erase operation is performed. For example, if each programming operation uses 16 bytes of space, a maximum of 128 programming operations may be performed before it becomes necessary to erase the block in order to continue. In this way the effective number of overwrites can be kept low. The effective overwrite count can be further reduced by evenly dividing operations between block A and block B. It is recommended that data be retained on the number of times each block has been erased and a limit count set. 5. If a block erase error occurs, execute the clear status regist er command followed by the block erase command a minimum of three times and until the erase error is no longer generated. Table 9 Summary of 3803 group (Spec.L)’s flash memory version Item Specifications Power source voltage (VCC)V CC = 2.7 to 5.5 V Program/Erase VPP voltage (VPP)V CC = 2.7 to 5.5 V Flash memory mode 3 modes; Parallel I/O mode, Standard serial I/O mode, CPU rewrite mode Erase block division User ROM area/Data ROM area Refer to Figure 67. Boot ROM area (1) Not divided (4 Kbytes) Program method In units of bytes Erase method Block erase Program/Erase control method Program/Erase control by software command Number of commands 5 commands Number of program/Erase times 100(Max.) ROM code protection Available in parallel I/O mode and standard serial I/O mode Table 10 Electrical characteristics of flash memory (program ROM) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. − Byte programming time V CC = 5.0 V, Topr = 25 °C − 60 400 µs − Block erase time (Block 1) VCC = 5.0 V, Topr = 25 °C − 0.5 9 s (Block 2) − 0.9 9 s (Block 3) − 1.3 9 s (Block A, B) − 0.3 9 s
Rev.1.00 Apr 2, 2007 Page 70 of 117 REJ03B0212-0100 3803 Group (Spec.L) Boot Mode The control program for CPU rewrite mode must be written into the User ROM or Boot ROM area in parallel I/O mode beforehand. (If the control program is written into the Boot ROM area, the standard serial I/O mode becomes unusable.) See Figure 67 for details about the Boot ROM area. Normal microcomputer mode is entered when the microcomputer is reset with pulling CNVSS pin low. In this case, the CPU starts operating using the control program in the User ROM area. When the microcomputer is reset and the CNV SS pin high after pulling the P4 5/TxD1 pin and CNV SS pin high, the CPU starts operating (start address of progr am is stored into addresses FFFC 16 and FFFD 16) using the control program in the Boot ROM area. This mode is called the “Boot mode”. Also, User ROM area can be rewritten using the control program in the Boot ROM area. Block Address Block addresses refer to the maximum address of each block. These addresses are used in the block erase command. CPU Rewrite Mode In CPU rewrite mode, the internal flash memory can be operated on (read, program, or erase) under control of the Central Processing Unit (CPU). In CPU rewrite mode, only the User ROM area shown in Figure 67 can be rewritten; the Boot ROM area cannot be rewritten. Make sure the program and block erase commands are issued for only the User ROM area and each block area. The control program for CPU rewrite mode can be stored in either User ROM or Boot ROM area. In the CPU rewrite mode, because the flash memory cannot be read from the CPU, the rewrite control program must be transferred to internal RAM area before it can be executed. Fig 67. Block diagram of built-in flash memory Data block A:
2 Kbytes
Block 3: 24 Kbytes Block 2: 16 Kbytes Block 1: 8 Kbytes Block 0: 8 Kbytes FFFF16 E00016 C00016 800016 200016 180016 100016 User ROM area Data block B: (2 Kbytes) FFFF16 100016 0FFF16 0FE016 083F16 004016 000016 FFFF16 F00016 Boot ROM area
4 Kbytes
Internal flash memory area (60 Kbytes) RAM Notes 1: The boot ROM area can be rewritten in a parallel I/O mode. (Access to except boot ROM area is disabled.) 2: To specify a block, use the maximum address in the block. 3: The mask ROM version has the reserved ROM area. Note the difference of the area.
Rev.1.00 Apr 2, 2007 Page 71 of 117 REJ03B0212-0100 3803 Group (Spec.L) Outline Performance CPU rewrite mode is usable in the single-chip or Boot mode. The only User ROM area can be rewritten. In CPU rewrite mode, the CPU erases, programs and reads the internal flash memory as instructed by software commands. This rewrite control program must be transferred to internal RAM area before it can be executed. The MCU enters CPU rewrite m ode by setting “1” to the CPU rewrite mode select bit (bit 1 of address 0FE0 16). Then, software commands can be accepted. Use software commands to control program and erase operations. Whether a program or erase operation has terminated normally or in error can be verified by reading the status register. Figure 68 shows the flash memory control register 0. Bit 0 of the flash memory control register 0 is the RY/BY status flag used exclusively to read the operating status of the flash memory. During programming and erase operations, it is “0” (busy). Otherwise, it is “1” (ready). Bit 1 of the flash memory contro l register 0 is the CPU rewrite mode select bit. When this bit is set to “1”, the MCU enters CPU rewrite mode. And then, software commands can be accepted. In CPU rewrite mode, the CPU b ecomes unable to access the internal flash memory directly . Therefore, use the control program in the internal RAM for write to bit 1. To set this bit 1 to “1”, it is necessary to write “0” and then write “1” in succession to bit 1. The bit can be set to “0” by only writing “0”. Bit 2 of the flash memory control register 0 is the 8 KB user block E/W enable bit. By setting combination of bit 4 of the flash memory control register 2 and this bit as shown in Table 11, E/W is disabled to user block in the CPU rewriting mode. Bit 3 of the flash memory contro l register 0 is the flash memory reset bit used to reset the control circuit of internal flash memory. This bit is used when flash me mory access has failed. When the CPU rewrite mode select bit is “1”, setting “1” for this bit resets the control circuit. To release the reset, it is necessary to set this bit to “0”. Bit 5 of the flash memory control register 0 is the User ROM area select bit and is valid only in the boot mode. Setting this bit to “1” in the boot mode switches an accessible area from the boot ROM area to the user ROM area. To use the CPU rewrite mode in the boot mode, set this bit to “1”. To rewrite bit 5, execute the useroriginal reprogramming contro l software transferred to the internal RAM in advance. Bit 6 of the flash memory control register 0 is the program status flag. This bit is set to “1” when writing to flash memory is failed. When program error occurs, the block cannot be used. Bit 7 of the flash memory contro l register 0 is the erase status flag. This bit is set to “1” when erasing flash memory is failed. When erase error occurs, the block cannot be used. Figure 69 shows the flash memory control register 1. Bit 0 of the flash memory control register 1 is the Erase suspend enable bit. By setting this bit to “1”, the erase suspend mode to suspend erase processing temporaly when block erase command is executed can be used. In order to set this bit to “1”, writing “0” and “1” in succession to bit 0. In order to set this bit to “0”, write “0” only to bit 0. Bit 1 of the flash memory control register 1 is the erase suspend request bit. By setting this bit to “1” when erase suspend enable bit is “1”, the erase processing is suspended. Bit 6 of the flash memory control register 1 is the erase suspend flag. This bit is cleared to “0” at the flash erasing. Fig 68. Structure of flash memory control register 0 Fig 69. Structure of flash memory control register 1 Flash memory control register 0 (FMCR0: address : 0FE016: initial value: 0116) RY/BY status flag 0 : Busy (being written or erased) 1 : Ready CPU rewrite mode select bit (1) 0 : CPU rewrite mode invalid 1 : CPU rewrite mode valid
8 KB user block E/W enable bit(1, 2)
0 : E/W disabled 1 : E/W enabled Flash memory reset bit(3, 4) 0 : Normal operation 1 : reset Not used (do not write “1” to this bit.) User ROM area select bit(5) 0 : Boot ROM area is accessed 1 : User ROM area is accessed Program status flag 0: Pass 1: Error Erase status flag 0: Pass 1: Error b7 b0 Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a “1” to it in succession. For this bit to be set to “0”, write “0” only to this bit. 2: This bit can be written only when CPU rewrite mode select bit is “1”. 3: Effective only when the CPU rewrite mode select bit = “1”. Fix this bit to “0” when the CPU rewrite mode select bit is “0”. 4: When setting this bit to “1” (when the control circuit of flash memory is reset), the flash memory cannot be accessed for 10 µs. 5: Write to this bit in program on RAM Flash memory control register 1 (FMCR1: address : 0FE116: initial value: 4016) Erase Suspend enble bit(1) 0 : Suspend invalid 1 : Suspend valid Erase Suspend request bit(2) 0 : Erase restart 1 : Suspend request Not used (do not write “1” to this bit.) Erase Suspend flag 0 : Erase active 1 : Erase inactive (Erase Suspend mode) Not used (do not write “1” to this bit.) b7 b0 Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a “1” to it in succession. For this bit to be set to “0”, write “0” only to this bit. 2: Effective only when the suspend enable bit = “1”.
Rev.1.00 Apr 2, 2007 Page 72 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 70. Structure of flash memory control register 2 Figure 71 shows a flowchart for setting/releasing CPU rewrite mode. Fig 71. CPU rewrite mode set/release flowchart be sure to execute Flash memory control register 2 (FMCR2: address : 0FE216: initial value: 4516) Not used Not used (do not write “1” to this bit.) Not used All user block E/W enable bit (1, 2) 0 : E/W disabled 1 : E/W enabled Not used b7 b0 Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a “1” to it in succession. For this bit to be set to “0”, write “0” only to this bit. 2: Effective only when the CPU rewrite mode select bit = “1”. Table 11 State of E/W inhibition function All user block E/W enable bit
8 KB user block
8 KB × 2 block
Addresses C00016 to FFFF16
16 KB + 24 KB block
Addresses 200016 to BFFF16 Data block Addresses 100016 to 1FFF16 0 0 E/W disabled E/W disabled E/W enabled 0 1 E/W disabled E/W disabled E/W enabled 1 0 E/W disabled E/W enabled E/W enabled 1 1 E/W enabled E/W enabled E/W enabled Start Single-chip mode or Boot mode Set CPU mode register(1) Jump to control program transferred to internal RAM (Subsequent operations are executed by control program in this RAM) Transfer CPU rewrite mode control program to internal RAM Set CPU rewrite mode select bit to “1” (by writing “0” and then “1” in succession) Using software command executes erase, program, or other operation End Write “0” to CPU rewrite mode select bit Set all user block E/W enable bit to “1” (by writing “0” and then “1” in succession) Set 8 KB user block E/W enable bit (At E/W disabled; writing “0” , at E/W enabled; writing “0” and then “1” in succession Execute read array command(2) Set all user block E/W enable bit to “0” Set 8 KB user block E/W enable bit to “0” Notes 1: Set the main clock as follows depending on the clock division ratio selection bits of CPU mode register (bits 6, 7 of address 003B16). 2: Before exiting the CPU rewrite mode after completing erase or program operation, always be sure to execute the read array command.
Rev.1.00 Apr 2, 2007 Page 73 of 117 REJ03B0212-0100 3803 Group (Spec.L) <Notes on CPU Rewrite Mode> Take the notes described below when rewriting the flash memory in CPU rewrite mode. (1) Operation speed During CPU rewrite mode, set the system clock φ to 4.0 MHz or less using the clock division rati o selection bits (bits 6 and 7 of address 003B16). (2) Instructions inhibited against use The instructions which refer to the internal data of the flash memory cannot be used during CPU rewrite mode. (3) Interrupts The interrupts cannot be used during CPU rewrite mode because they refer to the internal data of the flash memory. (4) Watchdog timer If the watchdog timer has been al ready activated, internal reset due to an underflow will not occur because the watchdog timer is surely cleared during program or erase. (5) Reset Reset is always valid. The MCU is activated using the boot mode at release of reset in the condition of CNV SS = “H”, so that the program will begin at the address which is stored in addresses FFFC16 and FFFD16 of the boot ROM area.
Rev.1.00 Apr 2, 2007 Page 74 of 117 REJ03B0212-0100 3803 Group (Spec.L) Software Commands Table 12 lists the software commands. After setting the CPU rewrite mode select bit to “1”, execute a software command to specify an erase or program operation. Each software command is explained below.
- Read Array Command (FF 16) The read array mode is entere d by writing the command code “FF16” in the first bus cycle. When an address to be read is input in one of the bus cycles that foll ow, the contents of the specified address are read out at the data bus (D0 to D7). The read array mode is retained until another command is written.
- Read Status Register Command (70 16) When the command code “7016” is written in the first bus cycle, the contents of the status register are read out at the data bus (D0 to D7) by a read in the second bus cycle. The status register is explained in the next section.
- Clear Status Register Command (5016) This command is used to clear the bits SR4 and SR5 of the status register after they have been set. These bits indicate that operation has ended in an error. To use this command, write the command code “5016” in the first bus cycle.
- Program Command (4016) Program operation starts when the command code “40 16” is written in the first bus cycle. Th en, if the address and data to program are written in the 2nd bus cycle, program operation (data programming and verification) will start. Whether the write operation is completed can be confirmed by read status register or the RY/BY status flag. When the program starts, the read status register mode is entered automatically and the contents of the status register is read at the data bus (D 0 to D7). The status register bit 7 (SR7) is set to “0” at the same time the write operation starts and is returned to “1” upon completion of the write operation. In this cas e, the read status register mode remains active until the read array command (FF16) is written. The RY/BY status flag of the flash memory control register is “0” during write operation and “1” when the write operation is completed as is the status register bit 7. At program end, program result s can be checked by reading the status register. Fig 72. Program flowchart NOTES: 1. SRD = Status Register Data 2. WA = Write Address, WD = Write Data 3. BA = Block Address to be erased (Input the maximum address of each block.) 4. X denotes a given address in the User ROM area. Start Write “4016” SR7 = “1”? or RY/BY = “1”? Read status register Program completed NO YES Write Write address Write data SR4 = “0”? Program error NO YES Table 12 List of software commands (CPU rewrite mode) Command cycle number First bus cycle Second bus cycle Mode Address Data (D0 to D7) Mode Address Data (D0 to D7) Read array 1 Write X(4) FF16 Read status register 2 Write X 70 16 Read X SRD(1) Clear status register 1 Write X 50 16 Program 2 Write X 40 16 Write WA(2) WD(2) Block erase 2 Write X 20 16 Write BA(3) D016
Rev.1.00 Apr 2, 2007 Page 75 of 117 REJ03B0212-0100 3803 Group (Spec.L)
- Block Erase Command (2016/D016) By writing the command code “20 16” in the first bus cycle and the confirmation command code “D016” and the block address in the second bus cycle that follows, the block erase (erase and erase verify) operation starts for the block address of the flash memory to be specified. Whether the block erase operation is completed can be confirmed by read status register or the RY/BY status flag of flash memory control register. At the same time the block erase operation starts, the read status register mode is automatically entered, so that the contents of the status register can be read out. The status register bit 7 (SR7) is set to “0” at the same time the block erase operation starts and is returned to “1” upon completion of the block erase operation. In this case, the read status register mode remains active until the read array command (FF 16) is written. The RY/BY status flag is “0” during block erase operation and “1” when the block erase operation is completed as is the status register bit 7. After the block erase ends, er ase results can be checked by reading the status register. For de tails, refer to the section where the status register is detailed. Fig 73. Erase flowchart Write “2016” Write “D016” Blockaddress Read status register SR7 = “1”? or RY/BY = “1”? Erase completed (write read command “FF16”) NO YES Start SR5 = “0”? Erase error YES NO
Rev.1.00 Apr 2, 2007 Page 76 of 117 REJ03B0212-0100 3803 Group (Spec.L)
- Status Register The status register shows the operating status of the flash memory and whether erase op erations and programs ended successfully or in error. It can be read in the following ways: (1) By reading an arbitrary address from the User ROM area after writing the read status register command (7016) (2) By reading an arbitrary addr ess from the User ROM area in the period from when the program starts or erase operation starts to when the read array command (FF16) is input. Also, the status register can be cleared by writing the clear status register command (5016). After reset, the status register is set to “8016”. Table 13 shows the status register . Each bit in this register is explained below.
- Sequencer status (SR7) The sequencer status indicates th e operating status of the flash memory. This bit is set to “0” (busy) during write or erase operation and is set to “1” when these operations ends. After power-on, the sequencer status is set to “1” (ready).
- Erase status (SR5) The erase status indicates the operating status of erase operation. If an erase error occurs, it is set to “1”. When the erase status is cleared, it is reset to “0”.
- Program status (SR4) The program status indicates th e operating status of write operation. When a write error occurs, it is set to “1”. The program status is reset to “0” when it is cleared. If “1” is written for any of the SR5 and SR4 bits, the read array, program, and block erase commands are not accepted. Before executing these commands, execute the clear status register command (50 16) and clear the status register. Also, if any commands are not correct, both SR5 and SR4 are set to “1”. Table 13 Definition of each bit in status register Each bit of SRD bits Status name Definition “1” “0” SR7 (bit7) Sequencer status Ready Busy SR6 (bit6) Reserved −− SR5 (bit5) Erase status Terminated in error Terminated normally SR4 (bit4) Program status Terminated in error Terminated normally SR3 (bit3) Reserved −− SR2 (bit2) Reserved −− SR1 (bit1) Reserved −− SR0 (bit0) Reserved −−
Rev.1.00 Apr 2, 2007 Page 77 of 117 REJ03B0212-0100 3803 Group (Spec.L) Full Status Check By performing full status check, it is possible to know the execution results of erase and program operations. Figure 74 shows a full status check flowch art and the action to be taken when each error occurs. Fig 74. Full status check flowchart and remedial procedure for errors Read status register SR4 = “1” and SR5 = “1”? Command sequence error YES Execute the clear status register command (5016) to clear the status register. Try performing the operation one more time after confirming that the command is entered correctly. NO SR5 = “0”? YES Erase errorNO Should an erase error occur, the block in error cannot be used. SR4 = “0”? YES Program error NO End (block erase, program) Note: When one of SR5 and SR4 is set to “1”, none of the read array, program, and block erase commands is accepted. Execute the clear status register command (5016) before executing these commands. Should a program error occur, the block in error cannot be used.
Rev.1.00 Apr 2, 2007 Page 78 of 117 REJ03B0212-0100 3803 Group (Spec.L) Functions To Inhibit Rewriting Flash Memory Version To prevent the contents of internal flash memory from being read out or rewritten easily, this MCU incorporates a ROM code protect function for use in parallel I/O mode and an ID code check function for use in standard serial I/O mode.
- ROM Code Protect Function The ROM code protect function is the function to inhibit reading out or modifying the contents of internal flash memory by using the ROM code protect control address (address FFDB 16) in parallel I/O mode. Figure 75 shows the ROM code protect control address (address FFDB 16). (This address exists in the User ROM area.) If one or both of the pair of RO M code protect bits is set to “0”, the ROM code protect is turned on, so that the contents of internal flash memory are protected against readout and modification. The RO M code protect is implemented in two levels. If level 2 is selected, the flash memory is protected even against readout by a shipment inspection LSI tester, etc. When an attempt is made to select both level 1 and level 2, level 2 is selected by default. If both of the two ROM code protect reset bits are set to “00”, the ROM code protect is turned off, so that the contents of internal flash memory can be readout or modified. Once the ROM code protect is turned on, the contents of the ROM code protect reset bits cannot be modified in parall el I/O mode. Use the serial I/O or CPU rewrite mode to rewrite the contents of the ROM code protect reset bits. Rewriting of only the ROM code protect control address (address FFDB 16) cannot be performed. Wh en rewriting the ROM code protect reset bit, rewrite the whole user ROM area (block 0) containing the ROM code protect control address. Fig 75. Structure of ROM code protect control address ROM code protect control address (address FFDB16) ROMCP (FF16 when shipped) Reserved bits (“1” at read/write) ROM code protect level 2 set bits (ROMCP2)(1, 2) b3b2 0 0: Protect enabled 0 1: Protect enabled 1 0: Protect enabled 1 1: Protect disabled ROM code protect reset bits (ROMCR) (3) b5b4 0 0: Protect removed 0 1: Protect set bits effective 1 0: Protect set bits effective 1 1: Protect set bits effective ROM code protect level 1 set bits (ROMCP1) (1) b7b6 0 0: Protect enabled 0 1: Protect enabled 1 0: Protect enabled 1 1: Protect disabled 1 1 Notes 1: When ROM code protect is turned on, the internal flash memory is protected against readout or modification in parallel I/O mode. 2: When ROM code protect level 2 is turned on, ROM code readout by a shipment inspection LSI tester, etc. also is inhibited. 3: The ROM code protect reset bits can be used to turn off ROM code protect level 1 and ROM code protect level 2. However, since these bits cannot be modified in parallel I/O mode, they need to be rewritten in serial I/O mode or CPU rewrite mode.
Rev.1.00 Apr 2, 2007 Page 79 of 117 REJ03B0212-0100 3803 Group (Spec.L)
- ID Code Check Function Use this function in standard serial I/O mode. When the contents of the flash memory are not blank, the ID code sent from the programmer is compared with the ID code written in the flash memory to see if they match. If the ID codes do not match, the commands sent from the programmer are not accepted. The ID code consists of 8-bit data, and its areas are FFD4 16 to FFDA16. Write a program which has had the ID code preset at these addresses to the flash memory. Fig 76. ID code store addresses ID7 ID6 ID5 ID4 ID3 ID2 ID1 Address ROM code protect control Interrupt vector area FFD516 FFD416 FFD616 FFD716 FFD816 FFD916 FFDA16 FFDB16
Rev.1.00 Apr 2, 2007 Page 80 of 117 REJ03B0212-0100 3803 Group (Spec.L) Parallel I/O Mode The parallel I/O mode is used to input/output software commands, address and data in parallel for operation (read, program and erase) to internal flash memory. Use the external device (write r) only for 3803 group (Spec.L) flash memory version. For details, refer to the userÅfs manual of each writer manufacturer.
- User ROM and Boot ROM Areas In parallel I/O mode, the User ROM and Boot ROM areas shown in Figure 67 can be rewritten. Both areas of flash memory can be operated on in the same way. The Boot ROM area is 4 Kbytes in size and located at addresses F00016 through FFFF 16. Make sure program and block erase operations are always performed within this address range. (Access to any location outside this address range is prohibited.) In the Boot ROM area, an eras e block operation is applied to only one 4 Kbyte block. The boot ROM area has had a standard serial I/O mode control program stored in it when shipped from the fac-tory. Therefore, using th e MCU in standard serial I/O mode, do not rewrite to the Boot ROM area.
Rev.1.00 Apr 2, 2007 Page 81 of 117 REJ03B0212-0100 3803 Group (Spec.L) Standard serial I/O Mode The standard serial I/O mode inputs and outputs the software commands, addresses and data needed to operate (read, program, erase, etc.) the internal flash memory. This I/O is clock synchronized serial. This m ode requires a purpose-specific peripheral unit. The standard serial I/O mode is different from the parallel I/O mode in that the CPU controls flash memory re write (uses the CPU rewrite mode), rewrite data input and so forth. The standard serial I/O mode is started by connecting “H” to the CNV SS pin and “H” to the P4 5 (BOOTENT) pin, and releasing the reset operation. (In the ordinary microcomputer mode, set CNVSS pin to “L” level.) This control program is written in the Boot ROM area when the product is ship ped from Renesas. Accordingly, make note of the fact that the standard serial I/O mode cannot be used if the Boot ROM area is rewritten in parallel I/O mode. The standard serial I/ O mode has st andard serial I/O mode 1 of the clock synchronous serial and standa rd serial I/O mode 2 of the clock asynchronous seri al. Table 14 and 15 show description of pin function (standard serial I/O mode). Figure 77 to 80 show the pin connections for the standard serial I/O mode. In standard serial I/O mode, only the User ROM area shown in Figure 67 can be rewritten. The Boot ROM area cannot be written. In standard serial I/O mode, a 7-byte ID code is used. When there is data in the flash memory, this function determines whether the ID code sent from the peripheral unit (programmer) and those written in the flash memory match. The commands sent from the peripheral unit (programmer) are not accepted unless the ID code matches.
Rev.1.00 Apr 2, 2007 Page 82 of 117 REJ03B0212-0100 3803 Group (Spec.L) Table 14 Description of pin function (Flash Memory Serial I/O Mode 1) Pin name Signal name I/O Function VCC,VSS Power supply I Apply 2.7 to 5.5 V to the V CC pin and 0 V to the VSS pin. CNVSS CNVSS I After input of port is set, input “H” level. RESET Reset input I Reset input pin. To reset the microcomputer, RESET pin should be held at an “L” level for 16 cycles or more of XIN. XIN Clock input I Connect an oscill ation circuit between the XIN and XOUT pins. As for the connection method, refer to the “clock generating circuit”.XOUT Clock output O AVSS Analog power supply input Connect AV SS to VSS. VREF Reference voltage input I Apply reference voltage of A/D to this pin. P00−P07, P10−P17, P20−P27, P30−P37, P40−P43, P50−P57, P60−P67 I/O port I/O Input “L” or “H” level, or keep open. P44 RxD input I Serial data input pin. P45 TxD output O Serial data output pin. P46 SCLK input I Serial clock input pin. P47 BUSY output O BUSY signal output pin. Table 15 Description of pin function (Flash Memory Serial I/O Mode 2) Pin name Signal name I/O Function VCC,VSS Power supply I Apply 2.7 to 5.5 V to the V CC pin and 0 V to the VSS pin. CNVSS CNVSS I After input of port is set, input “H” level. RESET Reset input I Reset input pin. To reset the microcomputer, RESET pin should be held at an “L” level for 16 cycles or more of XIN. XIN Clock input I Connect an oscill ation circuit between the XIN and XOUT pins. As for the connection method, refer to the “clock generating circuit”.XOUT Clock output O AVSS Analog power supply input Connect AV SS to VSS. VREF Reference voltage input I Apply reference voltage of A/D to this pin. P00−P07, P10−P17, P20−P27, P30−P37, P40−P43, P50−P57, P60−P67 I/O port I/O Input “L” or “H” level, or keep open. P44 RxD input I Serial data input pin. P45 TxD output O Serial data output pin. P46 SCLK input I Input “L” level. P47 BUSY output O BUSY signal output pin.
Rev.1.00 Apr 2, 2007 Page 83 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 77. Connection for standard serial I/O mode 1 (M38039FFLHP/KP) 0/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P16 P14 P15 P17 P27(LED7) P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) VSS XOUT XIN P42/INT1 RESET CNVSS P40/INT40/XCOUT P41/INT00/XCIN P35/TXD3 P34/RXD3 P31/DA2 P30/DA1 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P37/SRDY3 P36/SCLK3 P33 P32 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR 1 P54/CNTR 0 P52/SCLK2 P51/SOUT2 P50/SIN2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P62/AN2 P47/SRDY1 /CNTR 2 P53/SRDY2 M38039FFLHP/KP RESET CNVSS RxD TxD SCLK BUSY *Connect oscillation circuit. indicates flash memory pin. VCC VSS
Rev.1.00 Apr 2, 2007 Page 84 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 78. Connection for standard serial I/O mode 2 (M38039FFLHP/KP) 0/AN8 P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P16 P14 P15 P17 P27(LED7) P20(LED0) P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) VSS XOUT XIN P42/INT1 RESET CNVSS P40/INT40/XCOUT P41/INT00/XCIN P35/TXD3 P34/RXD3 P31/DA2 P30/DA1 VCC VREF AVSS P67/AN7 P66/AN6 P65/AN5 P64/AN4 P63/AN3 P37/SRDY3 P36/SCLK3 P33 P32 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR 1 P54/CNTR 0 P52/SCLK2 P51/SOUT2 P50/SIN2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P62/AN2 P47/SRDY1 /CNTR 2 P53/SRDY2 M38039FFLHP/KP RESET CNVSS RxD TxD BUSY *Connect oscillation circuit. indicates flash memory pin. VCC VSS “L” input
Rev.1.00 Apr 2, 2007 Page 85 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 79. Connection for standard serial I/O mode 1 (M38039FFLSP) P30/DA1 P31/DA2 P34/RXD3 P35/TXD3 P00/AN8 P20(LED0) P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) P32 P33 P36/SCLK3 P37/SRDY3 M38039FFLSP VCC VREF AVSS P67/AN7 P66/AN6 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P52/SCLK2 P51/SOUT2 P50/SIN2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS P40/INT40/XCOUT XIN XOUT VSS RESET P53/SRDY2 P65/AN5 P41/INT00/XCIN P47/SRDY1/CNTR2 VSS RESET CNVSS RXD TXD SCLK BUSY VCC *Connect oscillation circuit. indicates flash memory pin.
Rev.1.00 Apr 2, 2007 Page 86 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 80. Connection for standard serial I/O mode 2 (M38039FFLSP) P30/DA1 P31/DA2 P34/RXD3 P35/TXD3 P00/AN8 P20(LED0) P01/AN9 P02/AN10 P03/AN11 P04/AN12 P05/AN13 P06/AN14 P07/AN15 P10/INT41 P11/INT01 P12 P13 P14 P15 P16 P17 P21(LED1) P22(LED2) P23(LED3) P24(LED4) P25(LED5) P26(LED6) P27(LED7) P32 P33 P36/SCLK3 P37/SRDY3 M38039FFLSP VCC VREF AVSS P67/AN7 P66/AN6 P64/AN4 P63/AN3 P62/AN2 P61/AN1 P60/AN0 P57/INT3 P56/PWM P55/CNTR1 P54/CNTR0 P52/SCLK2 P51/SOUT2 P50/SIN2 P46/SCLK1 P45/TXD1 P44/RXD1 P43/INT2 P42/INT1 CNVSS P40/INT40/XCOUT XIN XOUT VSS RESET P53/SRDY2 P65/AN5 P41/INT00/XCIN P47/SRDY1/CNTR2 VSS RESET CNVSS RXD TXD “L” input BUSY VCC *Connect oscillation circuit. indicates flash memory pin.
Rev.1.00 Apr 2, 2007 Page 87 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 81. Connection for standard serial I/O mode 1 (M38039FFLWG) P61/AN1 P60/AN0 P55/CNTR1 P52/SCLK2 P50/SIN2 P44/RXD1 P43/INT2 CNVSS P67/AN7 P66/AN6 P57/INT3 P54/CNTR0 P47/SRDY1/CNTR2 P45/TXD1 P40/INT40/XCOUT P41/INT00/XCIN P30/DA1 P31/DA2 P32 P37/SRDY3 P17 P14 P15 P16 P33 P34/RXD3 P00/AN8 P05/AN13 P12 P13 P26(LED6)P 2 7(LED7) P35/TXD3 P01/AN9 P03/AN11 P06/AN14 P11/INT01 P25(LED5)P 2 3(LED3)P 2 4(LED4) P36/SCLK3 P02/AN10 P04/AN12 P07/AN15 P10/INT41 P20(LED0)P 2 1(LED1)P 2 2(LED2) P62/AN2 P63/AN3 VREF AVSS VCC VSS XIN XOUT ABCDEFGH ABCDEFGH 50 46 44 41 40 32 31 30 51 47 45 42 39 27 29 28 53 52 48 43 38 37 26 25 56 55 54 49 33 36 35 34 1 64 58 59 57 24 22 23 60 61 4 7 12 14 21 20 62 63 5 8 10 13 17 19 2 3 6 9 11 15 16 18 PIN CONFIGURATION (TOP VIEW) indicates flash memory pin. CNVSS RESET VCC VSS BUSY TXD RXD SCLK P65/AN5 P64/AN4 P56/PWM P5 3/SRDY2 P51/SOUT2 P46/SCLK1 P42/INT1 RESET
Rev.1.00 Apr 2, 2007 Page 88 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 82. Connection for standard serial I/O mode 2 (M38039FFLWG) P61/AN1 P60/AN0 P55/CNTR1 P52/SCLK2 P50/SIN2 P44/RXD1 P43/INT2 CNVSS P67/AN7 P66/AN6 P57/INT3 P54/CNTR0 P47/SRDY1/CNTR2 P45/TXD1 P40/INT40/XCOUT P41/INT00/XCIN P30/DA1 P31/DA2 P32 P37/SRDY3 P17 P14 P15 P16 P33 P34/RXD3 P00/AN8 P05/AN13 P12 P13 P26(LED6)P 2 7(LED7) P35/TXD3 P01/AN9 P03/AN11 P06/AN14 P11/INT01 P25(LED5)P 2 3(LED3)P 2 4(LED4) P36/SCLK3 P02/AN10 P04/AN12 P07/AN15 P10/INT41 P20(LED0)P 2 1(LED1)P 2 2(LED2) P62/AN2 P63/AN3 VREF AVSS VCC VSS XIN XOUT ABCDEFGH ABCDEFGH 50 46 44 41 40 32 31 30 51 47 45 42 39 27 29 28 53 52 48 43 38 37 26 25 56 55 54 49 33 36 35 34 1 64 58 59 57 24 22 23 60 61 4 7 12 14 21 20 62 63 5 8 10 13 17 19 2 3 6 9 11 15 16 18 PIN CONFIGURATION (TOP VIEW) * Connect oscillation circuit. indicates flash memory pin. CNVSS RESET VCC VSS BUSY TXD RXD “L”input P65/AN5 P64/AN4 P56/PWM P5 3/SRDY2 P51/SOUT2 P46/SCLK1 P42/INT1 RESET
Rev.1.00 Apr 2, 2007 Page 89 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 83. Operating waveform for standard serial I/O mode 1 Fig 84. Operating waveform for standard serial I/O mode 2 Power source RESET CNVSS P45(TXD) P46(SCLK) P47(BUSY) P44(RXD) td(CNVSS-RESET) td(P45-RESET) Notes: In the standard serial I/O mode 1, input “H” to the P46 pin. Be sure to set the CNVSS pin to “H” before rising RESET. Be sure to set the P45 pin to “H” before rising RESET.td(CNVSS-RESET) td(P45-RESET) Symbol Min. Max.Typ. Unit ms ms Limits Power source RESET CNVSS P45(TXD) P47(BUSY) P44(RXD) P46(SCLK) td(CNVSS-RESET) td(P45-RESET) td(CNVSS-RESET) td(P45-RESET) Symbol Min. Max.Typ. Unit ms ms Limits Notes: In the standard serial I/O mode 2, input “H” to the P46 pin. Be sure to set the CNVSS pin to “H” before rising RESET. Be sure to set the P45 pin to “H” before rising RESET.
Rev.1.00 Apr 2, 2007 Page 90 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 85. When using programmer (in standard serial I/O mode 1) of Suisei Electronics System Co., LTD, connection example 3803 Group (Spec. L) T_VDD T_VPP T_RXD T_SCLK T_PGM/OE/MD T_RESET GND RESET circuit Set the same termination as the single-chip mode. VCC P45 (TXD) P46 (SCLK) P47 (BUSY) RESET VSS AVSS XIN XOUT Note: For the programming circuit, the wiring capacity of each signal pin must not exceed 47 pF. T_BUSY T_TXD 4.7kΩ P44 (RXD) CNVSS 4.7kΩ N.C.
Rev.1.00 Apr 2, 2007 Page 91 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 86. When using E8 programmer (in standard serial I/O mode 1), connection example 3803 Group (Spec. L) RESET circuit Set the same termination as the single-chip mode. VCC P45 (TXD) P44 (RXD) P46 (SCLK) RESET VSS AVSS XIN XOUT *1 : Open-collector buffer Note : For the programming circuit, the wiring capacity of each signal pin must not exceed 47 pF. VCC CNVSS 4.7 kΩ 4.7 kΩ P47 (BUSY) 4.7 kΩ
Rev.1.00 Apr 2, 2007 Page 92 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTES NOTES ON PROGRAMMING 1. Processor Status Register (1) Initializing of proc essor status register Flags which affect program execution must be initialized after a reset. In particular, it is essential to initialize the T and D flags because they have an important effect on calculations. <Reason> After a reset, the contents of the processor status register (PS) are undefined except for the I flag which is “1”. Fig 87. Initialization of processor status register (2) How to reference the processor status register To reference the contents of the processor status register (PS), execute the PHP instruction once then read the contents of (S+1). If necessary, execute the PLP inst ruction to return the PS to its original status. Fig 88. Stack memory contents after PHP instruction execution 2. Decimal calculations (1) Execution of decimal calculations The ADC and SBC are the only instructions which will yield proper decimal notation, set the decimal mode flag (D) to “1” with the SED instruction. Af ter executing the ADC or SBC instruction, execute another in struction before executing the SEC, CLC, or CLD instruction. (2) Notes on status flag in decimal mode When decimal mode is selected, the values of three of the flags in the status register (the N, V, and Z flags) are invalid after a ADC or SBC instruction is executed. The carry flag (C) is set to “1” if a carry is generated as a result of the calculation, or is cleared to “0” if a borrow is generated. To determine whether a calculation has generated a carry, the C flag must be initialized to “0” before each calculation. To check for a borrow, the C flag must be initialized to “1” before each calculation. Fig 89. Execution of decimal calculations 3. JMP instruction When using the JMP instruction in indirect addressing mode, do not specify the last address on a page as an indirect address. 4. Multiplication and Division Instructions
- The index X mode (T) and th e decimal mode (D) flags do not affect the MUL and DIV instruction.
- The execution of these inst ructions does not change the contents of the processor status register. 5. Ports The contents of the port direction registers cannot be read. The following cannot be used:
- The data transfer instruction (LDA, etc.)
- The operation instruction when the index X mode flag (T) is “1”
- The instruction with the addressing mode which uses the value of a direction register as an index
- The bit-test instruction (BBC or BBS, etc.) to a direction register
- The read-modify-write instructions (ROR, CLB, or SEB, etc.) to a direction register. Use instructions such as LDM and STA, etc., to set the port direction registers. 6. Instruction Execution Timing The instruction execution time can be obtained by multiplying the frequency of the internal clock φ by the number of cycles mentioned in the 740 Family Software Manual. The frequency of the internal clock φ is the twice the XIN cycle in high-speed mode, 8 times the X IN cycle in middle-speed mode, and the twice the XCIN in low-speed mode. Reset Initializing of flags Main program Stored PS (S) (S) + 1 Set D flag to “1” ADC or SBC instruction NOP instruction SEC, CLC, or CLD instruction
Rev.1.00 Apr 2, 2007 Page 93 of 117 REJ03B0212-0100 3803 Group (Spec.L) Countermeasures against noise (1) Shortest wiring length 1. Wiring for RESET pin Make the length of wiring which is connected to the RESET pin as short as possible. Especially, connect a capacitor across the RESET pin and the V SS pin with the shortest possible wiring (within 20mm). <Reason> The width of a pulse input into the RESET pin is determined by the timing necessary conditions. If noise having a shorter pulse width than the standard is input to the RESET pin, the reset is released before the internal st ate of the microcomputer is com- pletely initialized. This may cause a program runaway. Fig 90. Wiring for the RESET pin 2. Wiring for clock input/output pins
- Make the length of wiring whic h is connected to clock I/O pins as short as possible.
- Make the length of wiring (within 20 mm) across the grounding lead of a capacitor which is connected to an oscillator and the V SS pin of a microcomputer as short as possible.
- Separate the VSS pattern only for oscillation from other VSS pat-terns. <Reason> If noise enters clock I/O pins, clock waveforms may be deformed. This may cause a program failure or program runaway. Also, if a potential diff erence is caused by the noise between the V SS level of a microcomputer and the V SS level of an oscillator, the correct cl ock will not be input in the microcomputer. Fig 91. Wiring for clock I/O pins (2) Connection of bypass capacitor across V SS line and VCC line In order to stabilize the system operation and avoid the latch-up, connect an approximately 0.1 µF bypass capacitor across the VSS line and the VCC line as follows:
- Connect a bypass capacitor across the VSS pin and the VCC pin at equal length.
- Connect a bypass capacitor across the VSS pin and the VCC pin with the shortest possible wiring.
- Use lines with a larger diameter than other signal lines for VSS line and VCC line.
- Connect the power source wiring via a bypass capacitor to the VSS pin and the VCC pin. Fig 92. Bypass capacitor across the V SS line and the VCC line RESETReset circuit Noise VSSVSS N.G. Reset circuit VSS RESET VSS O.K. Noise XIN XOUT VSS N.G. XIN XOUT VSS O.K. VSS VCC VSS VCC N.G. O.K.
Rev.1.00 Apr 2, 2007 Page 94 of 117 REJ03B0212-0100 3803 Group (Spec.L) (3) Oscillator concerns In order to obtain the stabiliz ed operation clock on the user system and its condition, contact the oscillator manufacturer and select the oscillator and oscillation circuit constants. Be careful espe-cially when range of votage and temperature is wide. Also, take care to prevent an oscillator that generates clocks for a microcomputer operation from being affected by other signals. 1. Keeping oscillator away from large current signal lines Install a microcomputer (and especially an oscillator) as far as possible from signal lines where a current larger than the toler- ance of current value flows. <Reason> In the system using a microcom puter, there are signal lines for controlling motors, LEDs, and ther mal heads or others. When a large current flows through t hose signal lines, strong noise occurs because of mutual inductance. 2. Installing osc illator away from signa l lines where potential levels change frequently Install an oscillator and a conne cting pattern of an oscillator away from signal lines where potential levels change fre- quently. Also, do not cross such signal lines over the clock lines or the signal lines which are sensitive to noise. <Reason> Signal lines where potential levels change frequently (such as the CNTR pin signal line) may affect other lines at signal rising edge or falling edge. If such lines cross over a clock line, clock wave- forms may be deformed, which causes a microcomputer failure or a program runaway. Fig 93. Wiring for a large current signal line/Wiring of signal lines where potential levels change frequently (4) Analog input The analog input pin is connected to the capacitor of a voltage com-parator. Accordingly, su fficient accuracy may not be obtained by the charge/discharge current at the time of A/D conversion when the analog signal source of high-impedance is connected to an analog input pin. In order to obtain the A/D conversion result stabilized more, please lower the impedance of an analog signal source, or a dd the smoothing capacitor to an analog input pin. (5) Difference of memory size When memory size differ in one group, actual values such as an electrical characteristics, A/D conversion accuracy, and the amount of -proof of noise incorrect operation may differ from the ideal values. When these products are used switching, perform system evalua-tion for each product of every after confirming product specification. (6) Wiring to CNV SS pin The CNVSS pin determines the flash memory mode. Connect the CNVSS pin the shortest possible to the GND pattern which is supplied to the VSS pin of the microcomputer. In addition connecting an approximately 5 k Ω. resistor in series to the GND could improve noise immunity. In this case as well as the above mention, connect the pin the shortest possible to the GND pattern which is supplied to the V SS pin of the microcomputer. Note. When the boot mode or the standard serial I/O mode is used, a switch of the input level to the CNVSS pin is required. Fig 94. Wiring for the CNV SS XIN XOUT VSS M Microcomputer Mutual inductance Large current GND XIN XOUT VSS CNTRDo not cross N.G. 1. Keeping oscillator away from large current signal lines 2. Installing oscillator away from signal lines where potential levels change frequently The shortest CNVSS VSS Approx. 5kΩ The shortest(Note) (Note) Note: Shows the microcomputer’s pin.
Rev.1.00 Apr 2, 2007 Page 95 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTES ON PERIPHERAL FUNCTIONS Notes on Input and Output Ports 1. Notes in standby state In standby state *1 for low-power dissipat ion, do not make input levels of an I/O port “undefined ”. Even when an I/O port of Nchannel open-drain is set as output mode, if output data is “1”, the aforementioned notes are necessary. Pull-up (connect the port to VCC) or pull-down (connect the port to VSS) these ports through a resistor. When determining a resistance value, note the following points:
- External circuit
- Variation of output levels during the ordinary operation When using built-in pull-up resistor, note on varied current values:
- When setting as an input port : Fix its input level
- When setting as an output port : Prevent current from flowing out to external <Reason> Exclusive input ports are always in a high-impedance state. An output transistor becomes an OFF state when an I/O port is set as input mode by the direction regi ster, so that the port enter a highimpedance state. At this time, the potential which is input to the input buffer in a microcomputer is unstable in the state that input levels are “undefined”. This may cause power source current. Even when an I/O port of N-channel open-drain is set as output mode by the direction register, if the contents of the port latch is “1”, the same phenomenon as that of an input port will occur. *1 Standby state : stop mode by executing STP instruction wait mode by executing WIT instruction 2. Modifying output data with bit managing instruction When the port latch of an I/O port is modified with the bit managing instruction *1, the value of the unspecified bit may be changed. <Reason> I/O ports are set to input or out put mode in bit units. Reading from a port register or writi ng to it involves the following operations.
- Port in input mode Read: Read the pin level. Write: Write to the port latch.
- Port in output mode Read: Read the port latch or read the output from the peripheral function (specifications differ depending on the port). Write: Write to the port latch. (The port latch value is output from the pin.) Since bit managing instructions *1 are read-modify-write instructions,*2 using such an instruction on a port register causes a read and write to be performed simultaneously on the bits other than the one specified by the instruction. When an unspecified bit is in input mode, its pin level is read and that value is written to the port la tch. If the previous value of the port latch differs from the pin level, the port latch value is changed. If an unspecified bit is in output mode, the port latch is generally read. However, for some ports the peripheral function output is read, and the value is written to the port latch. In this case, if the previous value of the port latch differs from the peripheral function output, the port latch value is changed. *1 Bit managing instructions: SEB and CLB instructions *2 Read-modify-write instructions: Instructions that read memory in byte units, modify the value, and then write the result to the same location in memory in byte units Termination of Unused Pins 1. Terminate unused pins (1) Output ports : Open (2) I/O ports :
- Set the I/O ports for the inpu t mode and connect them to VCC or VSS through each resistor of 1 kΩ to 10 kΩ. Ports that permit the selecting of a built-in pull-up resistor can also use this resistor. Set the I/O ports for the output mode and open them at “L” or “H”.
- When opening them in the output mode, the input mode of the initial status remains until the m ode of the ports is switched over to the output mode by the program after reset. Thus, the potential at these pins is undefined and the power source current may increase in the in put mode. With regard to an effects on the system, thorough ly perform system evaluation on the user side.
- Since the direction register setup may be changed because of a program runaway or noise, set direction registers by program periodically to increase the reliability of program. (3) The AV SS pin when not using the A/D converter :
- When not using the A/D converte r, handle a power source pin for the A/D converter, AVSS pin as follows: AVSS: Connect to the VSS pin. 2. Termination remarks (1) I/O ports : Do not open in the input mode. <Reason>
- The power source current ma y increase depending on the firststage circuit.
- An effect due to noise may be easily produced as compared with proper termination (2) in 1 and shown on the above. (2) I/O ports : When setting for the input mode, do not connect to V CC or VSS directly. <Reason> If the direction register set up changes for the output mode because of a program runaway or noise, a short circuit may occur between a port and VCC (or VSS). (3) I/O ports : When setting for the input mode, do not connect multiple ports in a lump to VCC or VSS through a resistor. <Reason> If the direction register set up changes for the output mode because of a program runaway or noise, a short circuit may occur between ports.
- At the termination of unused pins, perform wiring at the shortest possible distance (20 mm or less) from micro- computer pins.
Rev.1.00 Apr 2, 2007 Page 96 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on Interrupts 1. Change of relevant register settings When the setting of the following registers or bits is changed, the interrupt request bit may be set to “1”. When not requiring the interrupt occurrence synchronized with these setting, take the following sequence.
- Interrupt edge selection register (address 003A16)
- Timer XY mode register (address 002316)
- Timer Z mode register (address 002A16) Set the above listed registers or bits as the following sequence. Fig 95. Sequence of changing relevant register <Reason> When setting the followings, the interrupt request bit may be set to “1”.
- When setting external interrupt active edge Concerned register: Interrupt edge selection register (address 003A16) Timer XY mode register (address 002316) Timer Z mode register (address 002A16)
- When switching interrupt sources of an interrupt vector address where two or more interrupt sources are allocated. Concerned register: Interrupt source selection register (address 003916) 2. Check of interrupt request bit When executing the BBC or BBS instruction to an interrupt request bit of an interrupt requ est register immediately after this bit is set to “0”, execute one or more instructions before executing the BBC or BBS instruction. Fig 96. Sequence of check of interrupt request bit <Reason> If the BBC or BBS instruction is executed immediately after an interrupt request bit of an interr upt request regist er is cleared to “0”, the value of the interrupt request bit before being cleared to “0” is read. Set the interrupt edge select bit (active edge switch bit) or the interrupt (source) select bit to “1”. NOP (one or more instructions) Set the corresponding interrupt enable bit to “0” (disabled). Set the corresponding interrupt request bit to “0” (no interrupt request issued). Set the corresponding interrupt enable bit to “1” (enabled). NOP (one or more instructions) Clear the interrupt request bit to “0” (no interrupt issued) Execute the BBC or BBS instruction
Rev.1.00 Apr 2, 2007 Page 97 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on 8-bit Timer (timer 1, 2, X, Y)
- If a value n (between 0 and 255) is written to a timer latch, the frequency division ratio is 1/(n+1).
- When switching the count sour ce by the timer 12, X and Y count source selection bits, the value of timer count is altered in unconsiderable amount owing to generating of thin pulses in the count input signals. Therefore, select the timer count source before set the value to the prescaler and the timer.
- Set the double-function port of the CNTR 0/CNTR1 pin and port P54/P55 to output in the pulse output mode.
- Set the double-function port of CNTR 0/CNTR1 pin and port P54/P55 to input in the event counter mode and the pulse width measurement mode. Notes on 16-bit Timer (timer Z) 1. Pulse output mode
- Set the double-function port of the CNTR2 pin and port P47 to output. 2. Pulse period measurement mode
- Set the double-function port of the CNTR2 pin and port P47 to input.
- A read-out of timer value is impossible in this mode. The timer can be written to only duri ng timer stop (no measurement of pulse period).
- Since the timer latch in this mode is specialized for the read- out of measured values, do not perform any write operation during measurement.
- “FFFF16” is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse period measurement depends on the timer value just before measurement start. 3. Pulse width measurement mode
- Set the double-function port of the CNTR 2 pin and port P47 to input.
- A read-out of timer value is impossible in this mode. The timer can be written to only duri ng timer stop (no measurement of pulse period).
- Since the timer latch in this mode is specialized for the read- out of measured values, do not perform any write operation during measurement.
- “FFFF16” is set to the timer when the timer underflows or when the valid edge of measurement start/completion is detected. Consequently, the timer value at start of pulse width measurement depends on the timer value just before measurement start. 4. Programmable waveform generating mode
- Set the double-function port of the CNTR 2 pin and port P47 to output. 5. Programmable one-shot generating mode
- Set the double-function port of CNTR 2 pin and port P4 7 to output, and of INT1 pin and port P42 to input in this mode.
- This mode cannot be used in low-speed mode.
- If the value of the CNTR 2 active edge swit ch bit is changed during one-shot generating en abled or generating one-shot pulse, then the output level from CNTR2 pin changes. 6. All modes
- Timer Z write control Which write control can be selected by the timer Z write control bit (bit 3) of the timer Z mode register (address 002A 16), writing data to both the latch and the timer at the same time or writing data only to the latch. When the operation “writing data only to the latch” is selected, the value is set to the timer latch by writing data to the address of timer Z and the timer is updated at next underflow. After reset release, the operation “writing data to both the latch and the timer at the same time” is selected, and the value is set to both the latch and the timer at the same time by writing data to the address of timer Z. In the case of writing data only to the latch, if writing data to the latch and an underflow are perform ed almost at the same time, the timer value may become undefined.
- Timer Z read control A read-out of timer value is impossible in pulse period measurement mode and pulse width measurement mode. In the other modes, a read-out of timer value is possible regardless of count operating or stopped. However, a read-out of timer latch value is impossible.
- Switch of interrupt active edge of CNTR 2 and INT1 Each interrupt active edge de pends on setting of the CNTR 2 active edge switch bit and the INT1 active edge selection bit.
- Switch of count source When switching the count sour ce by the timer Z count source selection bits, the value of timer count is altered in inconsiderable amount owing to generating of thin pulses on the count input signals. Therefore, select the timer count source before setting the value to the prescaler and the timer.
Rev.1.00 Apr 2, 2007 Page 98 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on Serial Interface 1. Notes when selecting clock synchronous serial I/O (1) Stop of transmission operation As for serial I/Oi (i = 1, 3) th at can be used as either a clock synchronous or an asynchronous (U ART) serial I/O, clear the serial I/Oi enable bit and the transmit enable bit to “0” (serial I/Oi and transmit disabled). <Reason> Since transmission is not stoppe d and the transmission circuit is not initialized even if only the seri al I/Oi enable bit is cleared to “0” (serial I/Oi disabled), the internal transmission is running (in this case, since pins TxDi, RxDi, S CLKi, and S RDYi function as I/O ports, the transmission data is not output). When data is written to the transmit buffer register in this state, data starts to be shifted to the transmit shift register. When the serial I/Oi enable bit is set to “1” at this time, the data during internally shifting is output to the TxDi pin and an operation failure occurs. (2) Stop of receive operation As for serial I/Oi (i = 1, 3) th at can be used as either a clock synchronous or an asynchronous (U ART) serial I/O, clear the receive enable bit to “0” (receive disabled), or clear the serial I/Oi enable bit to “0” (serial I/Oi disabled). (3) Stop of transmit/receive operation As for serial I/Oi (i = 1, 3) th at can be used as either a clock synchronous or an asynchronous (UART) serial I/O, clear both the transmit enable bit and receive enable bit to “0” (transmit and receive disabled). (when data is transmitted and re ceived in the clock synchronous serial I/O mode , any one of data transmission and reception cannot be stopped.) <Reason> In the clock synchronous serial I/O mode, the same clock is used for transmission and reception. If any one of transmission and reception is disabled, a bit error occurs because transmission and reception cannot be synchronized. In this mode, the clock circuit of the transmission circuit also operates for data reception. Accordingly, the transmission circuit does not stop by clearing only the transmit enable bit to “0” (transmit disabled). Also, the transmission circuit is not initialized by clearing the serial I/Oi enable bit to “0” (serial I/Oi disabled) (refer to (1) in 1.). 2. Notes when selecting clock asynchronous serial I/O (1) Stop of transmission operation Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/Oi enable bit (i = 1, 3) to “0”. <Reason> This is the same as (1) in 1. (2) Stop of receive operation Clear the receive enable bit to “0” (receive disabled). (3) Stop of transmit/receive operation Only transmission operation is stopped. Clear the transmit enable bit to “0” (transmit disabled). The transmission operation does not stop by clearing the serial I/Oi enable bit (i = 1, 3) to “0”. <Reason> This is the same as (1) in 1. Only receive operation is stopped. Clear the receive enable bit to “0” (receive disabled). 3. S RDYi (i = 1, 3) output of reception side When signals are output from the SRDYi pin on the reception side by using an external clock in the clock synchronous serial I/O mode, set all of the receive enable bit, the S RDYi output enable bit, and the transmit enable bit to “1” (transmit enabled). 4. Setting serial I/Oi (i = 1, 3) control register again Set the serial I/Oi control regi ster again after the transmission and the reception circuits are re set by clearing both the transmit enable bit and the receive enable bit to “0.” Fig 97. Sequence of setting serial I/Oi (i = 1, 3) control register again 5. Data transmission control with referring to transmit shift register completion flag After the transmit data is written to the transmit buffer register, the transmit shift register completion flag changes from “1” to “0” with a delay of 0.5 to 1.5 shift clocks. When data transmission is controlled with referring to the flag after writing the data to the transmit buffer register, note the delay. 6. Transmission control when external clock is selected When an external clock is used as the synchronous clock for data transmission, set the transmit enable bit to “1” at “H” of the S CLKi (i = 1, 3) input level. Also, write the transmit data to the transmit buffer register at “H” of the SCLKi input level. 7. Transmit interrupt request when transmit enable bit is set When using the transmit interrupt, take the following sequence. (1) Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to “0” (disabled). (2) Set the tranasmit enable bit to “1”. (3) Set the serial I/Oi transmit interrupt request bit (i = 1, 3) to “0” after 1 or more instruction has executed. (4) Set the serial I/Oi transmit interrupt enable bit (i = 1, 3) to “1” (enabled). <Reason> When the transmission enable bit is set to “1”, the transmit buffer empty flag and transmit shift register shift completion flag are also set to “1”. Therefore, regardless of se lecting which timing for the generating of transmit interrupts, the interrupt request is generated and the transmit interrupt request bit is set at this point. 8. Writing to baud rate generator i (BRGi) (i = 1, 3) Write data to the baud rate generator i (BRGi) (i = 1, 3) while the transmission/reception operation is stopped. Can be set with the LDM instruction at the same time Set the bits 0 to 3 and bit 6 of the serial I/Oi control register Clear both the transmit enable bit (TE) and the receive enable bit (RE) to “0” Set both the transmit enable bit (TE) and the receive enable bit (RE), or one of them to “1”
Rev.1.00 Apr 2, 2007 Page 99 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on PWM The PWM starts from “H” level af ter the PWM enable bit is set to enable and “L” level is temporarily output from the PWM pin. The length of this “L” level output is as follows: n + 1 2 × f(XIN) (s) (Count source selection bit = “0”, where n is the value set in the prescaler) n + 1 f(XIN) (s) (Count source selection bit = “1”, where n is the value set in the prescaler) Notes on A/D Converter 1. Analog input pin Make the signal source impedance for analog input low, or equip an analog input pin with an external capacitor of 0.01 µF to 1 µF. Further, be sure to verify the operation of application products on the user side. <Reason> An analog input pin includes the capacitor for analog voltage comparison. Accordingly, when signals from signal source with high impedance are input to an analog input pin, charge and discharge noise generates. This may cause the A/D conversion precision to be worse. 2. A/D converter power source pin The AV SS pin is A/D converter power source pins. Regardless of using the A/D conversion function or not, connect it as following :
- A VSS : Connect to the VSS line <Reason> If the AVSS pin is opened, the microcomputer may have a failure because of noise or others. 3. Clock frequency during A/D conversion The comparator consists of a cap acity coupling, and a charge of the capacity will be lost if the clock frequency is too low. Thus, make sure the following during an A/D conversion.
- f ( X IN) is 500 kHz or more
- Do not execute the STP instruction 4. Difference between at 8-bit reading in 10-bit A/D mode and at 8-bit A/D mode At 8-bit reading in the 10-bit A/D mode, “–1/2 LSB” correction is not performed to the A/D conversion result. In the 8-bit A/D mode, the A/D co nversion characteristics is the same as 3802 group’s charact eristics because “–1/2 LSB” correction is performed. Notes on D/A Converter 1. V CC when using D/A converter The D/A converter accuracy when V CC is 4.0 V or less differs from that of when V CC is 4.0 V or more. When using the D/A converter, we recommend using a VCC of 4.0 V or more. 2. DAi conversion register when not using D/A con- verter When a D/A converter is not us ed, set all values of the DAi conversion registers (i = 1, 2) to “00 16”. The initial value after reset is “0016”. Notes on Watchdog Timer
- Make sure that the watchdog timer H does not underflow while waiting Stop release, because the watchdog timer keeps counting during that term.
- When the STP instruction disable bit has been set to “1”, it is impossible to switch it to “0” by a program. Notes on RESET Pin Connecting capacitor In case where the RESET signal rise time is long, connect a ceramic capacitor or others across the RESET pin and the V SS pin. Use a 1000 pF or more capacitor for high frequency use. When connecting the capacitor, note the following :
- Make the length of the wiring which is connected to a capacitor as short as possible.
- Be sure to verify the operati on of application products on the user side. <Reason> If the several nanosecond or se veral ten nanosecond impulse noise enters the RESET pin, it may cause a microcomputer failure. Notes on Low-speed Operation Mode 1. Using sub-clock To use a sub-clock, fix bit 3 of the CPU mode register to “1” or control the Rd (refer to Figure 98) resistance value to a certain level to stabilize an oscillati on. For resistance value of Rd, consult the oscillator manufacturer. Fig 98. Ceramic resonator circuit <Reason> When bit 3 of the CPU mode regist er is set to “0”, the sub-clock oscillation may stop. 2. Switch between middle/high-speed mode and low- speed mode If you switch the mode betwee n middle/high-speed and low- speed, stabilize both X IN and X CIN oscillations. The sufficient time is required for the sub cl ock to stabilize, especially immediately after power on and at returning from stop mode. When switching the mode between middle/high-speed and low- speed, set the frequency on condition that f(XIN) > 3 × f(XCIN). Quartz-Crystal Oscillator When using the quartz-crystal oscillator of high frequency, such as 16 MHz etc., it may be necessary to select a specific oscillator with the specification demanded. XCIN XCOUT CCIN CCOUT Rd Rf
Rev.1.00 Apr 2, 2007 Page 100 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on Restarting Oscillation
- Restarting oscillation Usually, when the MCU stops the clock oscillation by STP instruction and the STP instruct ion has been released by an external interrupt source, the fixed values of Timer 1 and Prescaler 12 (Timer 1 = “01 16”, Prescaler 12 = “FF 16”) are automatically reloaded in orde r for the oscillation to stabilize. The user can inhibit the automatic setting by writing “1” to bit 0 of MISRG (address 001016). However, by setting this bit to “1”, the previous values, set just before the STP instruction was executed, will remain in Timer 1 and Prescaler 12. Therefore, you wi ll need to set an appropriate value to each register, in accordance with the oscillation stabilizing time, before executing the STP instruction. <Reason> Oscillation will restart when an ex ternal interrupt is received. However, internal clock φ is supplied to the CPU only when Timer 1 starts to underflow. This ensures time for the clock oscillation using the ceramic resonators to be stabilized. Notes on Using Stop Mode
- Register setting Since values of the prescaler 12 and Timer 1 are automatically reloaded when returning from the stop mode, set them again, respectively. (When the oscillation stabilizing time set after STP instruction released bit is “0”)
- Clock restoration After restoration from the stop mode to the normal mode by an interrupt request, the contents of the CPU mode register previous to the STP instruction execution are retained. Accordingly, if both main clock and sub clock were oscillating before execution of the STP instruction, the oscilla tion of both clocks is resumed at restoration. In the above case, when the main clock side is set as a system clock, the oscillation stabilizin g time for approximately 8,000 cycles of the X IN input is reserved at restoration from the stop mode. At this time, note that the oscillation on the sub clock side may not be stabilized even after the lapse of the oscillation stabilizing time of the main clock side. Notes on Wait Mode
- Clock restoration If the wait mode is released by a reset when X CIN is set as the system clock and X IN oscillation is stopped during execution of the WIT instruction, X CIN oscillation stops, X IN oscillations starts, and XIN is set as the system clock. In the above case, the RESET pin should be held at “L” until the oscillation is stabilized. Notes on CPU rewrite mode of flash memory version 1. Operation speed During CPU rewrite mode , set the system clock φ 4.0 MHz or less using the main clock division ratio selection bits (bits 6 and 7 of address 003B 16). 2. Instructions inhibited against use The instructions which refer to the internal data of the flash memory cannot be used during the CPU rewrite mode. 3. Interrupts inhibited against use The interrupts cannot be used during the CPU rewrite mode because they refer to the internal data of the flash memory. 4. Watchdog timer In case of the watchdog timer has been running already, the internal reset generated by watchdog timer underflow does not happen, because of watchdog timer is always clearing during program or erase operation. 5. Reset Reset is always vali d. In case of CNV SS = “H” when reset is released, boot mode is active. So the program starts from the address contained in address FFFC16 and FFFD16 in boot ROM area. Notes on flash memory version The CNVSS pin determines the flash memory mode. Connect the CNVSS pin the shortest possible to the GND pattern which is supplied to the VSS pin of the microcomputer. In addition connecting an approximately 5 k Ω. resistor in series to the GND could improve noise immunity. In this case as well as the above mention, connect the pin the shortest possible to the GND pattern which is supplied to the V SS pin of the microcomputer. Note. When the boot mode or the standard serial I/O mode is used, a switch of the input level to the CNVSS pin is required. Fig 99. Wiring for the CNV SS Notes on electric characteristic differences between mask ROM and flash nemory version MCUs There are differences in electric characteristics, operation margin, noise immunity, and noise radiation between Mask ROM and Flash Memory version MCUs due to the difference in the manufacturing processes, buil t-in ROM, and layout pattern etc. When manufacturing an application system with the Flash Memory version and then switching to use of the Mask ROM version, please conduct evaluations equivalent to the system evaluations conducted for the flash memory version. DATA REQUIRED FOR MASK ORDERS The following are necessary when ordering a mask ROM production: 1. Mask ROM Confirmation Form* 2. Mark Specification Form* 3. Data to be written to ROM, in EPROM form (three identical copies) * For the mask ROM confirmation and the mark specifications, refer to the “Renesas Technology Corp.” Homepage (http://www.renesas.com/en/rom). The shortest CNVSS VSS Approx. 5kΩ The shortest(Note) (Note) Note: Shows the microcomputer’s pin.
Rev.1.00 Apr 2, 2007 Page 101 of 117 REJ03B0212-0100 3803 Group (Spec.L) Notes on Handling of Power Source Pins In order to avoid a latch-up oc currence, connect a capacitor suitable for high frequencies as bypass capacitor between power source pin (VCC pin) and GND pin (VSS pin), and between power source pin (V CC pin) and analog power source input pin (AV SS pin). Besides, connect the capacito r to as close as possible. For bypass capacitor which should not be located too far from the pins to be connected, a ceramic capacitor of 0.01 µF–0.1 µF is recommended. Power Source Voltage When the power source voltage value of a microcomputer is less than the value which is indicat ed as the recommended operating conditions, the microc omputer does not operate normally and may perform unstable operation. In a system where the power source voltage drops slowly when the power source voltage drops or the power supply is turned off, reset a microcomputer when the power source voltage is less than the recommended operating conditions and design a system not to cause errors to the system by this unstable operation.
Rev.1.00 Apr 2, 2007 Page 102 of 117 REJ03B0212-0100 3803 Group (Spec.L)
ELECTRICAL CHARACTERISTICS
NOTE: 1. This value is 300 mW except SP package. Table 16 Absolute maximum ratings Symbol Parameter Conditions Ratings Unit VCC Power source voltages All voltages are based on V SS. When an input voltage is measured, output transistors are cut off. −0.3 to 6.5 V VI Input voltage P0 0-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67, VREF −0.3 to VCC + 0.3 V VI Input voltage P3 2, P33 −0.3 to 5.8 V VI Input voltage RESET, XIN −0.3 to VCC + 0.3 V VI Input voltage CNV SS −0.3 to VCC + 0.3 V VO P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67, XOUT −0.3 to VCC + 0.3 VOutput voltage VO Output voltage P3 2, P33 −0.3 to 5.8 V Pd Power dissipation Ta=25 °C 1000(1) mW Topr Operating temperature −20 to 85 °C Tstg Storage temperature −65 to 125 °C
Rev.1.00 Apr 2, 2007 Page 103 of 117 REJ03B0212-0100 3803 Group (Spec.L) Recommended operating conditions NOTES: 1. When using A/D converter, see A/D converter recommended operating conditions. 2. The start voltage and the start time for oscillation depend on t he using oscillator, oscillation circuit constant value and operating temperature range, etc.. Particularly a high-frequency oscillator might require some notes in the low voltage operation. 3. When the oscillation frequency has a duty cycle of 50%. 4. When using the microcomputer in low-speed mode, set the s ub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3. Table 17 Recommended operating conditions (1) (Mask ROM version) (VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Conditions Limits UnitMin. Typ. Max. VCC Power source voltage(1) When start oscillating(2) 2.2 5.0 5.5 V High-speed mode f(φ) = f(XIN)/2 f(XIN) ≤ 2.1 MHz 2.0 5.0 5.5 V f(XIN) ≤ 4.2 MHz 2.2 5.0 5.5 f(XIN) ≤ 8.4 MHz 2.7 5.0 5.5 f(XIN) ≤ 12.5 MHz 4.0 5.0 5.5 f(XIN) ≤ 16.8 MHz 4.5 5.0 5.5 Middle-speed mode f(φ) = f(XIN)/8 f(XIN) ≤ 6.3 MHz 1.8 5.0 5.5 V f(XIN) ≤ 8.4 MHz 2.2 5.0 5.5 f(XIN) ≤ 12.5 MHz 2.7 5.0 5.5 f(XIN) ≤ 16.8 MHz 4.5 5.0 5.5 VSS Power source voltage 0 V VIH “H” input voltage P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 1.8 ≤ VCC < 2.7 V 0.85 V CC VCC V 2.7 ≤ VCC ≤ 5.5 V 0.8 V CC VCC VIH “H” input voltage P32, P33 1.8 ≤ VCC < 2.7 V 0.85 V CC 5.5 V 2.7 ≤ VCC ≤ 5.5 V 0.8 V CC 5.5 VIH “H” input voltage RESET, XIN, XCIN, CNVSS 1.8 ≤ VCC < 2.7 V 0.85 V CC VCC V 2.7 ≤ VCC ≤ 5.5 V 0.8 V CC VCC VIL “L” input voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 1.8 ≤ VCC < 2.7 V 0 0.16 V CC V 2.7 ≤ VCC ≤ 5.5 V 0 0.2 V CC VIL “L” input voltage RESET, CNVSS 1.8 ≤ VCC < 2.7 V 0 0.16 V CC V 2.7 ≤ VCC ≤ 5.5 V 0 0.2 V CC VIL “L” input voltage XIN, XCIN 1.8 ≤ VCC ≤ 5.5 V 0 0.16 V CC V f(XIN) Main clock input oscillation frequency(3) High-speed mode f(φ) = f(XIN)/2 2.0 ≤ VCC < 2.2 V MHz 2.2 ≤ VCC < 2.7 V MHz 2.7 ≤ VCC < 4.0 V MHz 4.0 ≤ VCC < 4.5 V MHz 4.5 ≤ VCC ≤ 5.5 V 16.8 MHz Middle-speed mode f(φ) = f(XIN)/8 1.8 ≤ VCC < 2.2 V MHz 2.2 ≤ VCC < 2.7 V MHz 2.7 ≤ VCC < 4.5 V MHz 4.5 ≤ VCC ≤ 5.5 V 16.8 MHz f(XCIN) Sub-clock input oscillation frequency(3, 4) 32.768 50 kHz Mask ROM Version
Rev.1.00 Apr 2, 2007 Page 104 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTES: 1. When using A/D converter, see A/D converter recommended operating conditions. 2. The start voltage and the start time for oscillation depend on t he using oscillator, oscillation circuit constant value and operating temperature range, etc.. Particularly a high-frequency oscillator might require some notes in the low voltage operation. 3. When the oscillation frequency has a duty cycle of 50%. 4. When using the microcomputer in low-speed mode, set the s ub-clock input oscillation frequency on condition that f(XCIN) < f(XIN)/3. Table 18 Recommended operating conditions (2) (Flash memory version) (VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Conditions Limits UnitMin. Typ. Max. VCC Power source voltage(1) When start oscillating(2) 2.2 5.0 5.5 V High-speed mode f(φ) = f(XIN)/2 f(XIN) ≤ 8.4 MHz 2.7 5.0 5.5 V f(XIN) ≤ 12.5 MHz 4.0 5.0 5.5 f(XIN) ≤ 16.8 MHz 4.5 5.0 5.5 Middle-speed mode f(φ) = f(XIN)/8 f(XIN) ≤ 12.5 MHz 2.7 5.0 5.5 V f(XIN) ≤ 16.8 MHz 4.5 5.0 5.5 VSS Power source voltage 0 V VIH “H” input voltage P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67
0.8 VCC VCC V
VIH “H” input voltage P32, P33 0.8 VCC 5.5 V VIH “H” input voltage RESET, XIN, CNVSS VIH “H” input voltage XCIN 2V CC V VIL “L” input voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 0 0.2 V CC V VIL “L” input voltage RESET, CNVSS 0 0.2 V CC V VIL “L” input voltage XIN
0.16 VCC V
VIL “L” input voltage XCIN 0.4 V f(XIN) Main clock input oscillation frequency(3) High-speed mode f(φ) = f(XIN)/2 2.7 ≤ VCC < 4.0 V MHz 4.0 ≤ VCC < 4.5 V MHz 4.5 ≤ VCC ≤ 5.5 V 16.8 MHz Middle-speed mode f(φ) = f(XIN)/8 2.7 ≤ VCC < 4.5 V MHz 4.5 ≤ VCC ≤ 5.5 V 16.8 MHz f(XCIN) Sub-clock input oscillation frequency(3, 4) 32.768 50 kHz Flash Memory Version
Rev.1.00 Apr 2, 2007 Page 105 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTES: 1. The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an average value measured over 100 ms. The total peak current is the peak value of all the currents. 2. The peak output current is the peak current flowing in each port. 3. The average output current I OL(avg), IOH(avg) are average value measured over 100 ms. Table 19 Recommended operating conditions (3) (Mask ROM version: VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Limits UnitMin. Typ. Max. ΣIOH(peak) “H” total peak output current(1) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37 −80 mA ΣIOH(peak) “H” total peak output current(1) P40-P47, P50-P57, P60-P67 −80 mA ΣIOL(peak) “L” total peak output current(1) P00-P07, P10-P17, P30-P37 80 mA ΣIOL(peak) “L” total peak output current(1) P20-P27 80 mA ΣIOL(peak) “L” total peak output current(1) P40-P47, P50-P57, P60-P67 80 mA ΣIOH(avg) “H” total average output current(1) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37 −40 mA ΣIOH(avg) “H” total average output current(1) P40-P47, P50-P57, P60-P67 −40 mA ΣIOL(avg) “L” total average output current(1) P00-P07, P10-P17, P30-P37 40 mA ΣIOL(avg) “L” total average output current(1) P20-P27 40 mA ΣIOL(avg) “L” total average output current(1) P40-P47, P50-P57, P60-P67 40 mA IOH(peak) “H” peak output current(2) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 −10 mA IOL(peak) “L” peak output current(2) P00-P07, P10-P17, P30-P37, P40-P47, P50-P57, P60-P67 10 mA IOL(peak) “L” peak output current(2) P20-P27 20 mA IOH(avg) “H” average output current(3) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 −5m A IOL(avg) “L” average output current(3) P00-P07, P10-P17, P30-P37, P40-P47, P50-P57, P60-P67 5m A IOL(avg) “L” average output current(3) P20-P27 10 mA
Rev.1.00 Apr 2, 2007 Page 106 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTE: 1. P3 5 is measured when the P35/TXD3 P-channel output disable bit of the UART3 control register (bit 4 of address 003316) is “0”. P45 is measured when the P45/TXD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is “0”. Table 20 Electrical characteristics (1) (Mask ROM version: VCC = 1.8 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. VOH “H” output voltage(1) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 IOH = −10 mA VCC = 4.0 to 5.5 V VCC − 2.0 V IOH = –1.0 mA VCC = 1.8 to 5.5 V VCC − 1.0 VOL “L” output voltage P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 IOL = 10 mA VCC = 4.0 to 5.5 V 2.0 V IOL = 1.6 mA VCC = 1.8 to 5.5 V 1.0 VOL “L” output voltage P20-P27 IOL = 20 mA VCC = 4.0 to 5.5 V 2.0 V IOL = 1.6 mA VCC = 1.8 to 5.5 V 0.4 VT+ − VT− Hysteresis CNTR0, CNTR1, CNTR2, INT0-INT4 0.4 V VT+ − VT− Hysteresis RxD1, SCLK1, SIN2, SCLK2, RxD3, SCLK3 0.5 V VT+ − VT− Hysteresis RESET 0.5 V IIH “H” input current P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 VI = VCC (Pin floating, Pull-up transistor “off”) 5.0 µA IIH “H” input current RESET, CNVSS VI = VCC 5.0 µA IIH “H” input current XIN VI = VCC 4.0 µA IIL “L” input current P00-P07, P10-P17, P20-P27, P30-P37, P40-P47, P50-P57, P60-P67 VI = VSS (Pin floating, Pull-up transistor “off”) −5.0 µA IIL “L” input current RESET, CNVSS VI = VSS −5.0 µA IIL “L” input current XIN VI = VSS −4.0 µA IIL “L” input current (at Pull-up) P00-P07, P10-P17, P20-P27, P30, P31, P34-P37, P40-P47, P50-P57, P60-P67 VI = VSS VCC = 5.0 V −80 −210 −420 µA VI = VSS VCC = 3.0 V −30 −70 −140 VRAM RAM hold voltage When clock stopped 1.8 V CC V
Rev.1.00 Apr 2, 2007 Page 107 of 117 REJ03B0212-0100 3803 Group (Spec.L) Table 21 Electrical characteristics (2) (Mask ROM version) (VCC = 1.8 to 5.5 V, Ta = –20 to 85 °C, f(XCIN)=32.768 kHz (Stopped in middle-speed mode), Output transistors “off”, AD converter not operated) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. ICC Power source current High-speed mode VCC = 5.0 V f(X IN) = 16.8 MHz 8.0 15.0 mA f(XIN) = 12.5 MHz 6.5 12.0 f(XIN) = 8.4 MHz 5.0 9.0 f(XIN) = 4.2 MHz 2.5 5.0 f(XIN) = 16.8 MHz (in WIT state) 2.0 3.6 VCC = 3.0 V f(X IN) = 8.4 MHz 1.9 3.8 mA f(XIN) = 4.2 MHz 1.0 2.0 f(XIN) = 2.1 MHz 0.6 1.2 Middle-speed mode VCC = 5.0 V f(X IN) = 16.8 MHz 4.0 7.0 mA f(XIN) = 12.5 MHz 3.0 6.0 f(XIN) = 8.4 MHz 2.5 5.0 f(XIN) = 16.8 MHz (in WIT state) 1.8 3.3 VCC = 3.0 V f(X IN) = 12.5 MHz 1.5 3.0 mA f(XIN) = 8.4 MHz 1.2 2.4 f(XIN) = 6.3 MHz 1.0 2.0 Low-speed mode VCC = 5.0 V f(X IN) = stopped 55 200 µA In WIT state 40 70 VCC = 3.0 V f(X IN) = stopped 15 40 µA In WIT state 8 15 VCC = 2.0 V f(X IN) = stopped 6 15 µA In WIT state 3 6 In STP state (All oscillation stopped) Ta = 25 °C0 . 1 1 . 0 µA Ta = 85 °C1 0 Increment when A/D conversion is executed f(XIN) = 16.8 MHz, VCC = 5.0 V In Middle-, high-speed mode 500 µA Mask ROM Version
Rev.1.00 Apr 2, 2007 Page 108 of 117 REJ03B0212-0100 3803 Group (Spec.L) Table 22 Electrical characterist ics (3) (Flash memory version) (VCC = 2.7 to 5.5 V, Ta = –20 to 85 °C, f(XCIN)=32.768 kHz (Stopped in middle-speed mode), Output transistors “off”, AD converter not operated) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. ICC Power source current High-speed mode VCC = 5.0 V f(X IN) = 16.8 MHz 5.5 8.3 mA f(XIN) = 12.5 MHz 4.5 6.8 f(XIN) = 8.4 MHz 3.5 5.3 f(XIN) = 4.2 MHz 2.2 3.3 f(XIN) = 16.8 MHz (in WIT state) 2.2 3.3 VCC = 3.0 V f(X IN) = 8.4 MHz 2.7 4.1 mA f(XIN) = 4.2 MHz 1.8 2.7 f(XIN) = 2.1 MHz 1.1 1.7 Middle-speed mode VCC = 5.0 V f(X IN) = 16.8 MHz 3.0 4.5 mA f(XIN) = 12.5 MHz 2.4 3.6 f(XIN) = 8.4 MHz 2.0 3.0 f(XIN) = 16.8 MHz (in WIT state) 2.1 3.2 VCC = 3.0 V f(X IN) = 12.5 MHz 1.7 2.6 mA f(XIN) = 8.4 MHz 1.5 2.3 f(XIN) = 6.3 MHz 1.3 2.0 Low-speed mode VCC = 5.0 V f(X IN) = stopped 410 630 µA In WIT state 4.5 6.8 VCC = 3.0 V f(X IN) = stopped 400 600 µA In WIT state 3.7 5.6 In STP state (All oscillation stopped) Ta = 25 °C 0.55 3.0 µA Ta = 85 °C0 . 7 5 Increment when A/D conversion is executed f(XIN) = 16.8 MHz, VCC = 5.0 V In Middle-, high-speed mode 1000 µA Flash Memory Version
Rev.1.00 Apr 2, 2007 Page 109 of 117 REJ03B0212-0100 3803 Group (Spec.L) A/D converter characteristics NOTES: 1. 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”. 2. 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”. NOTES: 1. 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”. 2. 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”. D/A converter characteristics NOTE: 1. Using one D/A converter, with the value in the DA c onversion register of the other D/A converter being “0016”. Table 23 A/D converter recommended operating conditions (Mask ROM version) (VCC = 2.0 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Conditions Limits UnitMin. Typ. Max. VCC Power source voltage (When A/D converter is used) 8-bit A/D mode(1) 2.0 5.0 5.5 V 10-bit A/D mode(2) 2.2 5.0 5.5 VREF Analog convert reference voltage 2.0 V CC V AVSS Analog power source voltage 0 V VIA Analog input voltage AN0-AN15 0V CC V f(XIN) Main clock input oscillation frequency (When A/D converter is used) 2.0 ≤ VCC = VREF < 2.2 V 0.5 MHz 2.2 ≤ VCC = VREF < 2.7 V 0.5 2.7 ≤ VCC = VREF < 4.0 V 0.5 4.0 ≤ VCC = VREF < 4.5 V 0.5 4.5 ≤ VCC = VREF ≤ 5.5 V 0.5 16.8 Table 24 A/D converter characteristics (Mask ROM version) (VCC = 2.0 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. − Resolution 8-bit A/D mode(1) 8b i t 10-bit A/D mode(2) 10 − Absolute accuracy (excluding quantization error) 8-bit A/D mode(1) 2.0 ≤ VREF < 2.2 V ±3 LSB 2.2 ≤ VREF ≤ 5.5 V ±2 10-bit A/D mode(2) 2.2 ≤ VREF < 2.7 V ±5 LSB 2.7 ≤ VREF ≤ 5.5 V ±4 tCONV Conversion time 8-bit A/D mode(1) 50 2tc(X IN) 10-bit A/D mode(2) 61 RLADDER Ladder resistor 12 35 100 k Ω IVREF Reference power source input current at A/D converter operated V REF = 5.0 V 50 150 200 µA at A/D converter stopped V REF = 5.0 V 5.0 µA II(AD) A/D port input current 5.0 µA Table 25 D/A converter characteristics (Mask ROM version) (VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Limits UnitMin. Typ. Max. − Resolution 8b i t − Absolute accuracy 4.0 ≤ VREF ≤ 5.5 V 1.0 % 2.7 ≤ VREF < 4.0 V 2.5 tsu Setting time 3 µs RO Output resistor 2 3.5 5 k Ω IVREF Reference power source input current(1) 3.2 mA Mask ROM Version
Rev.1.00 Apr 2, 2007 Page 110 of 117 REJ03B0212-0100 3803 Group (Spec.L) A/D converter characteristics NOTES: 1. 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”. 2. 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”. NOTES: 1. 8-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “1”. 2. 10-bit A/D mode: When the conversion mode selection bit (bit 7 of address 003816) is “0”. D/A converter characteristics NOTE: 1. Using one D/A converter, with the value in the DA c onversion register of the other D/A converter being “0016”. Table 26 A/D converter recommended operating conditions (Flash memory version) (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Conditions Limits UnitMin. Typ. Max. VCC Power source voltage (When A/D converter is used) 8-bit A/D mode(1) 2.7 5.0 5.5 V 10-bit A/D mode(2) 2.7 5.0 5.5 VREF Analog convert reference voltage 2.0 V CC V AVSS Analog power source voltage 0 V VIA Analog input voltage AN0-AN15 0V CC V f(XIN) Main clock input oscillation frequency (When A/D converter is used) 2.7 ≤ VCC = VREF < 4.0 V 0.5 MHz 4.0 ≤ VCC = VREF < 4.5 V 0.5 4.5 ≤ VCC = VREF ≤ 5.5 V 0.5 16.8 Table 27 A/D converter characteristics (Flash memory version) (VCC = 2.7 to 5.5 V, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. − Resolution 8-bit A/D mode(1) 8b i t 10-bit A/D mode(2) 10 − Absolute accuracy (excluding quantization error) 8-bit A/D mode(1) 2.7 ≤ VREF ≤ 5.5 V ±2 LSB 10-bit A/D mode(2) 2.7 ≤ VREF ≤ 5.5 V ±4 LSB tCONV Conversion time 8-bit A/D mode(1) 50 2tc(X IN) 10-bit A/D mode(2) 61 RLADDER Ladder resistor 12 35 100 k Ω IVREF Reference power source input current at A/D converter operated V REF = 5.0 V 50 150 200 µA at A/D converter stopped V REF = 5.0 V 5.0 µA II(AD) A/D port input current 5.0 µA Table 28 D/A converter characteristics (Flash memory version) (VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Limits UnitMin. Typ. Max. − Resolution 8b i t − Absolute accuracy 4.0 ≤ VREF ≤ 5.5 V 1.0 % 2.7 ≤ VREF < 4.0 V 2.5 tsu Setting time 3 µs RO Output resistor 2 3.5 5 k Ω IVREF Reference power source input current(1) 3.2 mA Table 29 Power source circuit timing ch aracteristics (Flash memory version) (VCC = 2.7 to 5.5 V, VREF = 2.7 V to VCC, VSS = AVSS = 0 V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. td(P−R) Internal power source stable time at power-on 2.7 ≤ VCC < 5.5 V 2 ms
Rev.1.00 Apr 2, 2007 Page 111 of 117 REJ03B0212-0100 3803 Group (Spec.L) Timing requirements and switching characteristics Table 30 Timing requirements (1) (Mask ROM version: VCC = 2.0 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0V, Ta = –20 to 85 °C, unless otherwise noted) Symbol Parameter Limits UnitMin. Typ. Max. tW(RESET) Reset input “L” pulse width 16 X IN cycle tC(XIN) Main clock X IN input cycle time 4.5 ≤ VCC ≤ 5.5 V 59.5 ns 4.0 ≤ VCC < 4.5 V 10000/(86 V CC − 219) 2.7 ≤ VCC < 4.0 V 26 × 103/(82 VCC − 3) 2.2 ≤ VCC < 2.7 V 10000/(84 V CC − 143) 2.0 ≤ VCC < 2.2 V 10000/(105 V CC − 189) tWH(XIN) Main clock X IN input “H” pulse width 4.5 ≤ VCC ≤ 5.5 V 25 ns 4.0 ≤ VCC < 4.5 V 4000/(86 V CC − 219) 2.7 ≤ VCC < 4.0 V 10000/(82 V CC − 3) 2.2 ≤ VCC < 2.7 V 4000/(84 V CC − 143) 2.0 ≤ VCC < 2.2 V 4000/(105 V CC − 189) tWL(XIN) Main clock X IN input “L” pulse width 4.5 ≤ VCC ≤ 5.5 V 25 ns 4.0 ≤ VCC < 4.5 V 4000/(86 V CC − 219) 2.7 ≤ VCC < 4.0 V 10000/(82 V CC − 3) 2.2 ≤ VCC < 2.7 V 4000/(84 V CC − 143) 2.0 ≤ VCC < 2.2 V 4000/(105 V CC − 189) tC(XCIN) Sub-clock X CIN input cycle time 20 µs tWH(XCIN) Sub-clock X CIN input “H” pulse width 5 µs tWL(XCIN) Sub-clock X CIN input “L” pulse width 5 µs tC(CNTR) CNTR 0−CNTR2 input cycle time 4.5 ≤ VCC ≤ 5.5 V 120 ns 4.0 ≤ VCC < 4.5 V 160 2.7 ≤ VCC < 4.0 V 250 2.2 ≤ VCC < 2.7 V 500 2.0 ≤ VCC < 2.2 V 1000 tWH(CNTR) CNTR 0−CNTR2 input “H” pulse width 4.5 ≤ VCC ≤ 5.5 V 48 ns 4.0 ≤ VCC < 4.5 V 64 2.7 ≤ VCC < 4.0 V 115 2.2 ≤ VCC < 2.7 V 230 2.0 ≤ VCC < 2.2 V 460 tWL(CNTR) CNTR 0−CNTR2 input “L” pulse width 4.5 ≤ VCC ≤ 5.5 V 48 ns 4.0 ≤ VCC < 4.5 V 64 2.7 ≤ VCC < 4.0 V 115 2.2 ≤ VCC < 2.7 V 230 2.0 ≤ VCC < 2.2 V 460 tWH(INT) INT 00, INT01, INT1, INT2, INT3, INT40, INT41 input “H” pulse width 4.5 ≤ VCC ≤ 5.5 V 48 ns 4.0 ≤ VCC < 4.5 V 64 2.7 ≤ VCC < 4.0 V 115 2.2 ≤ VCC < 2.7 V 230 2.0 ≤ VCC < 2.2 V 460 tWL(INT) INT 00, INT01, INT1, INT2, INT3, INT40, INT41 input “L” pulse width 4.5 ≤ VCC ≤ 5.5 V 48 ns 4.0 ≤ VCC < 4.5 V 64 2.7 ≤ VCC < 4.0 V 115 2.2 ≤ VCC < 2.7 V 230 2.0 ≤ VCC < 2.2 V 460
Rev.1.00 Apr 2, 2007 Page 112 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTE: 1. When bit 6 of address 001A 16 and bit 6 of address 003216 are “1” (clock synchronous). Divide this value by four when bit 6 of address 001A16 and bit 6 of address 003216 are “0” (UART). Table 31 Timing requirements (2) (Mask ROM version: VCC = 2.0 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) Symbol Parameter Limits UnitMin. Typ. Max. tC(SCLK1) tC(SCLK3) Serial I/O1, serial I/O3 clock input cycle time(1) 4.5 ≤ VCC ≤ 5.5 V 250 ns 4.0 ≤ VCC < 4.5 V 320 2.7 ≤ VCC < 4.0 V 500 2.2 ≤ VCC < 2.7 V 1000 2.0 ≤ VCC < 2.2 V 2000 tWH(SCLK1) tWH(SCLK3) Serial I/O1, serial I/O3 clock input “H” pulse width(1) 4.5 ≤ VCC ≤ 5.5 V 120 ns 4.0 ≤ VCC < 4.5 V 150 2.7 ≤ VCC < 4.0 V 240 2.2 ≤ VCC < 2.7 V 480 2.0 ≤ VCC < 2.2 V 950 tWL(SCLK1) tWL(SCLK3) Serial I/O1, serial I/O3 clock input “L” pulse width(1) 4.5 ≤ VCC ≤ 5.5 V 120 ns 4.0 ≤ VCC < 4.5 V 150 2.7 ≤ VCC < 4.0 V 240 2.2 ≤ VCC < 2.7 V 480 2.0 ≤ VCC < 2.2 V 950 tsu(RxD1-SCLK1) tsu(RxD3-SCLK3) Serial I/O1, serial I/O3 clock input setup time 4.5 ≤ VCC ≤ 5.5 V 70 ns 4.0 ≤ VCC < 4.5 V 90 2.7 ≤ VCC < 4.0 V 100 2.2 ≤ VCC < 2.7 V 200 2.0 ≤ VCC < 2.2 V 400 th(SCLK1-RxD1) th(SCLK3-RxD3) Serial I/O1, serial I/O3 clock input hold time 4.5 ≤ VCC ≤ 5.5 V 32 ns 4.0 ≤ VCC < 4.5 V 40 2.7 ≤ VCC < 4.0 V 50 2.2 ≤ VCC < 2.7 V 100 2.0 ≤ VCC < 2.2 V 200 tC(SCLK2)S e r i a l I / O 2 clock input cycle time 4.5 ≤ VCC ≤ 5.5 V 500 ns 4.0 ≤ VCC < 4.5 V 650 2.7 ≤ VCC < 4.0 V 1000 2.2 ≤ VCC < 2.7 V 2000 2.0 ≤ VCC < 2.2 V 4000 tWH(SCLK2)S e r i a l I / O 2 clock input “H” pulse width 4.5 ≤ VCC ≤ 5.5 V 200 ns 4.0 ≤ VCC < 4.5 V 260 2.7 ≤ VCC < 4.0 V 400 2.2 ≤ VCC < 2.7 V 950 2.0 ≤ VCC < 2.2 V 2000 tWL(SCLK2)S e r i a l I / O 2 clock input “L” pulse width 4.5 ≤ VCC ≤ 5.5 V 200 ns 4.0 ≤ VCC < 4.5 V 260 2.7 ≤ VCC < 4.0 V 400 2.2 ≤ VCC < 2.7 V 950 2.0 ≤ VCC < 2.2 V 2000 tsu(SIN2-SCLK2)S e r i a l I / O 2 clock input setup time 4.5 ≤ VCC ≤ 5.5 V 100 ns 4.0 ≤ VCC < 4.5 V 130 2.7 ≤ VCC < 4.0 V 200 2.2 ≤ VCC < 2.7 V 400 2.0 ≤ VCC < 2.2 V 800 th(SCLK2-SIN2)S e r i a l I / O 2 clock input hold time 4.5 ≤ VCC ≤ 5.5 V 100 ns 4.0 ≤ VCC < 4.5 V 130 2.7 ≤ VCC < 4.0 V 150 2.2 ≤ VCC < 2.7 V 300 2.0 ≤ VCC < 2.2 V 600
Rev.1.00 Apr 2, 2007 Page 113 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTE: 1. When the P4 5/TXD1 P-channel output disable bit of the UART1 control register (bit 4 of address 001B16) is “0”. Table 32 Switching characteristics (1) (Mask ROM version: VCC = 2.0 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. tWH(SCLK1) tWH(SCLK3) Serial I/O1, serial I/O3 clock output “H” pulse width 4.5 ≤ VCC ≤ 5.5 V Fig.100 tC(SCLK1)/2-30, tC(SCLK3)/2-30 ns 4.0 ≤ VCC < 4.5 V t C(SCLK1)/2-35, tC(SCLK3)/2-35 2.7 ≤ VCC < 4.0 V t C(SCLK1)/2-40, tC(SCLK3)/2-40 2.2 ≤ VCC < 2.7 V t C(SCLK1)/2-45, tC(SCLK3)/2-45 2.0 ≤ VCC < 2.2 V t C(SCLK1)/2-50, tC(SCLK3)/2-50 tWL(SCLK1) tWL(SCLK3) Serial I/O1, serial I/O3 clock output “L” pulse width 4.5 ≤ VCC ≤ 5.5 V t C(SCLK1)/2-30, tC(SCLK3)/2-30 ns 4.0 ≤ VCC < 4.5 V t C(SCLK1)/2-35, tC(SCLK3)/2-35 2.7 ≤ VCC < 4.0 V t C(SCLK1)/2-40, tC(SCLK3)/2-40 2.2 ≤ VCC < 2.7 V t C(SCLK1)/2-45, tC(SCLK3)/2-45 2.0 ≤ VCC < 2.2 V t C(SCLK1)/2-50, tC(SCLK3)/2-50 td(SCLK1-TxD1) td(SCLK3-TxD3) Serial I/O1, serial I/O3 output delay time(1) 4.5 ≤ VCC ≤ 5.5 V 140 ns 4.0 ≤ VCC < 4.5 V 200 2.7 ≤ VCC < 4.0 V 350 2.2 ≤ VCC < 2.7 V 400 2.0 ≤ VCC < 2.2 V 420 tV(SCLK1-TxD1) tV(SCLK3-TxD3) Serial I/O1, serial I/O3 output valid time(1) 4.5 ≤ VCC ≤ 5.5 V −30 ns 4.0 ≤ VCC < 4.5 V −30 2.7 ≤ VCC < 4.0 V −30 2.2 ≤ VCC < 2.7 V −30 2.0 ≤ VCC < 2.2 V −30 tr(SCLK1) tr(SCLK3) Serial I/O1, serial I/O3 rise time of clock output 4.5 ≤ VCC ≤ 5.5 V 30 ns 4.0 ≤ VCC < 4.5 V 35 2.7 ≤ VCC < 4.0 V 40 2.2 ≤ VCC < 2.7 V 45 2.0 ≤ VCC < 2.2 V 50 tf(SCLK1) tf(SCLK3) Serial I/O1, serial I/O3 fall time of clock output 4.5 ≤ VCC ≤ 5.5 V 30 ns 4.0 ≤ VCC < 4.5 V 35 2.7 ≤ VCC < 4.0 V 40 2.2 ≤ VCC < 2.7 V 45 2.0 ≤ VCC < 2.2 V 50 tWH(SCLK2) Serial I/O2 clock output “H” pulse width 4.5 ≤ VCC ≤ 5.5 V t C(SCLK2)/2-160 ns 4.0 ≤ VCC < 4.5 V t C(SCLK2)/2-200 2.7 ≤ VCC < 4.0 V t C(SCLK2)/2-240 2.2 ≤ VCC < 2.7 V t C(SCLK2)/2-260 2.0 ≤ VCC < 2.2 V t C(SCLK2)/2-280 tWL(SCLK2) Serial I/O2 clock output “L” pulse width 4.5 ≤ VCC ≤ 5.5 V t C(SCLK2)/2-160 ns 4.0 ≤ VCC < 4.5 V t C(SCLK2)/2-200 2.7 ≤ VCC < 4.0 V t C(SCLK2)/2-240 2.2 ≤ VCC < 2.7 V t C(SCLK2)/2-260 2.0 ≤ VCC < 2.2 V t C(SCLK2)/2-280 td(SCLK2-SOUT2) Serial I/O2 output delay time 4.5 ≤ VCC ≤ 5.5 V 200 ns 4.0 ≤ VCC < 4.5 V 250 2.7 ≤ VCC < 4.0 V 300 2.2 ≤ VCC < 2.7 V 350 2.0 ≤ VCC < 2.2 V 400 tV(SCLK2-SOUT2) Serial I/O2 output valid time 4.5 ≤ VCC ≤ 5.5 V 0 ns 4.0 ≤ VCC < 4.5 V 0 2.7 ≤ VCC < 4.0 V 0 2.2 ≤ VCC < 2.7 V 0 2.0 ≤ VCC < 2.2 V 0
Rev.1.00 Apr 2, 2007 Page 114 of 117 REJ03B0212-0100 3803 Group (Spec.L) NOTE: 1. When the P3 5/TXD3 P4-channel output disable bit of the UART3 control register (bit 4 of address 003316) is “0”. Fig 100. Circuit for measuring output switching characteristics Table 33 Switching characteristics (2) (Mask ROM version: VCC = 2.0 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) (Flash memory version: VCC = 2.7 to 5.5 V, VSS = 0 V, Ta = −20 to 85 °C, unless otherwise noted) Symbol Parameter Test conditions Limits UnitMin. Typ. Max. tf(SCLK2) Serial I/O2 fall time of clock output 4.5 ≤ VCC ≤ 5.5 V Fig.100 30 ns 4.0 ≤ VCC < 4.5 V 35 2.7 ≤ VCC < 4.0 V 40 2.2 ≤ VCC < 2.7 V 45 2.0 ≤ VCC < 2.2 V 50 tr(CMOS) CMOS rise time of output(1) 4.5 ≤ VCC ≤ 5.5 V 10 30 ns 4.0 ≤ VCC < 4.5 V 12 35 2.7 ≤ VCC < 4.0 V 15 40 2.2 ≤ VCC < 2.7 V 17 45 2.0 ≤ VCC < 2.2 V 20 50 tf(CMOS) CMOS fall time of output(1) 4.5 ≤ VCC ≤ 5.5 V 10 30 ns 4.0 ≤ VCC < 4.5 V 12 35 2.7 ≤ VCC < 4.0 V 15 40 2.2 ≤ VCC < 2.7 V 17 45 2.0 ≤ VCC < 2.2 V 20 50 Measurement output pin 100 pF CMOS output Measurement output pin 100 pF N-channel open-drain output 1kΩ
Rev.1.00 Apr 2, 2007 Page 115 of 117 REJ03B0212-0100 3803 Group (Spec.L) Fig 101. Timing diagram (in single-chip mode) tC(CNTR) tWL(CNTR)tWH(CNTR) 0.8VCC 0.2VCC CNTR0, CNTR1 CNTR2 INT1, INT2, INT3 INT00, INT40 INT01, INT41 RESET XIN tWL(INT)tWH(INT) 0.8VCC 0.2VCC 0.8VCC0.2VCC tW(RESET) tC(XIN) tWL(XIN)tWH(XIN) 0.8VCC 0.2VCC tC(SCLK1), tC(SCLK2), tC(SCLK3) tWL(SCLK1), tWL(SCLK2), tWL(SCLK3) 0.8VCC 0.2VCC tWH(SCLK1), tWH(SCLK2), tWH(SCLK3)tf tr tsu(RXD1-SCLK1), tsu(SIN2-SCLK2), tsu(RXD3-SCLK3) th(SCLK1-RXD1), th(SCLK2-SIN2), th(SCLK3-RXD3) td(SCLK1-TXD1), td(SCLK2-SOUT2), td(SCLK3-TXD3) tv(SCLK1-TXD1), tv(SCLK2-SOUT2), tv(SCLK3-TXD3) 0.2VCC 0.8VCC SCLK1 SCLK2 SCLK3 RXD1 RXD3 SIN2 TXD1 TXD3 SOUT2 XCIN tC(XCIN) tWL(XCIN)tWH(XCIN) 0.8VCC 0.2VCC Single-chip mode timing diagram
Rev.1.00 Apr 2, 2007 Page 116 of 117 REJ03B0212-0100 3803 Group (Spec.L) PACKAGE OUTLINE Diagrams showing the latest package dimensions and mounting information are available in the “Packages” section of the Renesas Technology website. 3.8A2 1.050.750.65b2 19.3518.75 19.05 0.60.50.4bp Previous CodeJEITA Package Code RENESAS Code PRDP0064BA-A 64P4B MASS[Typ.] 7.9gP-SDIP64-17x56.4-1.78 0.320.250.2 MaxNomMin Dimension in Millimeters Symbol Reference 56.656.456.2D 17.1517.016.85E A 1.31.00.9 0.38 2.8L c 1.778e 15° 5.08 1.528 2.028 INCLUDE TRIM OFFSET. DIMENSION "*3" DOES NOT NOTE) DO NOT INCLUDE MOLD FLASH. 3364 321 SEATING PLANE *3 *3 E c D L A b2e b3 bp Terminal cross section bp c DO NOT INCLUDE MOLD FLASH. NOTE) DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. Index mark 11 6 3348 F x y bp HE E HD D ZD ZE Detail F A c A2A1 L P-LQFP64-10x10-0.50 0.3g MASS[Typ.] 64P6Q-A / FP-64K / FP-64KVPLQP0064KB-A RENESAS CodeJEITA Package Code Previous Code 1.0 0.125 0.18 1.25 1.25 0.08 0.200.1450.09 0.250.200.15 MaxNomMin Dimension in Millimeters Symbol Reference 10.110.09.9D 10.110.09.9E 1.4A2 12.212.011.8 12.212.011.8 1.7A 0.150.10.05 0.650.50.35L x 8°0° c 0.5e 0.08y HD HE bp ZD ZE e
Rev.1.00 Apr 2, 2007 Page 117 of 117 REJ03B0212-0100 3803 Group (Spec.L) Terminal cross section bp c DO NOT INCLUDE MOLD FLASH. NOTE) DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET. 11 6 3348 F x y Index mark D HD E HE e bp ZD ZE Detail F c A A2A1 L Previous CodeJEITA Package Code RENESAS Code PLQP0064GA-A 64P6U-A MASS[Typ.] 0.7gP-LQFP64-14x14-0.80 1.0 0.125 0.35 1.0 1.0 0.20 0.200.1450.09 0.420.370.32 MaxNomMin Dimension in Millimeters Symbol Reference 14.114.013.9D 14.114.013.9E 1.4A2 16.216.015.8 16.216.015.8 1.7A 0.20.10 0.70.50.3L x 8°0° c 0.8e 0.10y HD HE bp ZD ZE 0.15v 0.20w Previous CodeJEITA Package Code RENESAS Code PTLG0064JA-A 64F0G MASS[Typ.] 0.07gP-TFLGA64-6x6-0.65 0.08 0.470.430.39 MaxNomMin Dimension in Millimeters Symbol Reference 6.0D 6.0E 1.05A x 0.65e 0.10y b 0.31 0.35 0.39 Bw Sw A S A H G F E D C B 12345678 S yS AB Index mark SA B v (Laser mark) Index mark D E A b e e
(1/1) REVISION HISTORY 3803 Group (Spec.L) Data Sheet Rev. Date Description Page Summary 1.00 Apr.2, 2007 − First edition issued
REVISION HISTORY
Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan http://www.renesas.com Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 RENESAS SALES OFFICES © 2007. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0