C.FL HIROSE

Document overview

  • PDF pages: 8

Technical content

Page 1

NEW

PDF page 1 diagram
PDF page 1 diagram
PDF page 1 diagram

■Features

1. Supports up to 30GHz

High frequency performance from DC to 30GHz. Suitable for the 28GHz band expected to be used in 5G communications.

2. Mated Height of 0.92mm (1.0mm Max.)

Receptacle mounting area is only 3.4mm2. Using the right-angle plug enables a mated height of 0.92mm, achieving the world's lowest class profile of coaxial connectors. (Fig.1)

3. Ultra lightweight

The world's smallest and lightest class of coaxial connectors. Receptacle : 3.3mg Right angle plug : 14.1mg

4. Automatic Board Placement

The embossed packaging allows for the receptacles to be automatically placed.

5. 50Ω Ultra-fine coaxial (fluorinated resin insulated) cables

Ultra-fine coaxial cables with a finished outer diameter of Ø0.64mm (single shield) allow for connection in small, confined spaces with smooth and easy operation.

6. Tactile Lock

Clear tactile lock on small connector enables reliable mating.

7. Simple Connector Mating and Unmating

Dedicated Insertion and Extraction tools to enable proper mating/unmating.

In cases where the application will demand a high level of reliability, such as automotive,

2022.1④

please contact a company representative for further information.

Page 2

■Product Specifi cations

Ratings Nominal characteristic impedance 50Ω Operating Temperature -40 to +90℃ (90%RH Max.)
Frequency Range : DC to 30GHz Storage Humidity Range -20 to +70℃ (90%RH Max.)
Item Specifications Conditions
1. Contact Resistance Center : 60mΩ Max. Exterior : 20mΩ Max. Measured at a maximum of 10mA
2. Insulation Resistance 500MΩ min Measured at 100V DC
3. Withstanding Voltage There shall be no flashover or dielectric breakdown Apply 200V for 1 minute
4. V.S.W.R.* 1.4 Max. DC to 15GHz
1.5 Max. 15 to 20GHz
1.6 Max. 20 to 30GHz
5. Durability Contact Resistance Center : 65mΩ Max. Exterior : 25mΩ Max. 20 mating cycles

\*V.S.W.R. Measuring System The above V.S.W.R. specification values are measured using the measurement system below.

<Plug Harness Measurement System>

Vector Network Analyzer
APC2.4(F) C.FLJ-H2.4P C.FL-LP(P)-044 100mm Double-ended Harness C.FLJ-H2.4P APC2.4(F)

D.U.T.

<Receptacle Measurement System>

Vector Network Analyzer
APC2.4(M) CONVERSION ADAPTOR Test Board C.FL-R-SMT-1 C.FLP-H2.4J APC2.4(M)

D.U.T.

Note 1 : The cable connector is measured with a 2.4mm conversion adapter attached to double-ended harness with an applicable 10cm cable. Note 2 : The board connector is measured while mounted to a 50Ω flourine board with a 2.4mm conversion adapter attached.

■Material / Finish

Component Material Finish/Remarks
Right angle Plug Shell Phosphor bronze Partial gold plating
Insulator LCP resin Black, UL94V-0
Female Central Contact Phosphor bronze Gold plating
Receptacle Shell Phosphor bronze Gold plating
Insulator LCP resin Black, UL94V-0
Male Central Contact Brass Gold plating
Adapter Shell Stainless steel Nickel Plating
Insulator PTFE resin ―
Male Center Contact Phosphor bronze Gold plating
Female Central Contact Beryllium copper Gold plating

Page 3

■Plug

  • C.FL-LP(P)-044 (Applicable Cable : outer diameter φ0.64mm)
PDF page 3 diagram
PDF page 3 diagram

Please order plug with as cabled assembly

■Cable Harness Specifi cation

The dimension specifications of the C.FL Series harness are as follows.

PDF page 3 diagram
  • Plug Product Number Structure
  • Cable Harness Total Length

Refer to the charts below for determining specific part number

Standard Tolerance

characteristics.

Total Length L Standard Tolerance (mm)
41≦L≦170 ±0.3

Please select connectors listed in this catalog when placing orders and be sure to check the latest delivery specifications at the time of ordering the product.

CFL - 2LPP - 044N「」TSH - A - L

❶

❷

❸ ❹ ❺

❻

❶Series Name C.FL ❹Cable Color 1 : White, 2 : Black, 4 : Blue
❷Harness Type 2LPP : Double-ended L-shaped plug harness ❺Cable Outer Conductor Specifications TSH : Tin plated coiled shield
❸Cable Type 044N : Ø0.64 cable ❻Total Length (mm) Length L (Based on mating center, Unit : mm)

BHigh Frequency Characteristic Data (Typical Value)

PDF page 3 diagram

Page 4

□Recommended PCB Mounting Pattern

■Receptacle

PDF page 4 diagram
PDF page 4 diagram
PDF page 4 diagram

Ø1.4

Part No. HRS No. Packaging RoHS2
C.FL-R-SMT-1(90) 331-2200-0 90 20,000 pieces per reel ○
  • Receptacle Product Number Structure Refer to the charts below to determine specific part number characteristics. Please select connectors listed in this catalog when placing orders and be sure to check specifications at the time of ordering.

❶Series Name C.FL

C.FL - R - SMT-1

❷Connector Type R : Receptacle

❶ ❷ ❸

❸Mounting Method SMT-1 : Surface Mounting

BHigh Frequency Characteristic Data (Typical Value)

PDF page 4 diagram
  • Embossed Tape Specifi cations
  • Reel Specifi cations

(JIS C 0806/IEC60286 Standard)

9.5

Pull Direction

PDF page 4 diagram
PDF page 4 diagram

(0.25)

(0.67)

Page 5

■Conversion Adapter

  • 2.4mm Conversion Adapter (Mated Portion : C.FL side : Jack-2.4mm side : Plug)
PDF page 5 diagram

8HEX

PDF page 5 diagram
Part No. HRS No. RoHS2
C.FLJ-H2.4P 311-0017-0 ○

Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements.

  • 2.4mm Conversion Adapter (Mated Portion : C.FL side : Plug-2.4mm side : Jack)
PDF page 5 diagram
PDF page 5 diagram

5.6

Part No. HRS No. RoHS2
C.FLP-H2.4J 311-0021-0 ○

Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements.

  • 2.92 Conversion Adapter (Mated Portion : C.FL side : Jack-2.92mm side : Plug)
PDF page 5 diagram

(11.99)

8HEX

PDF page 5 diagram
PDF page 5 diagram
Part No. HRS No. RoHS2
C.FLJ-HKP 311-0023-0 ○

Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements.

Page 6

  • 2.92 Conversion Adapter (Mated Portion : C.FL side : Plug-2.92mm side : Jack)
PDF page 6 diagram
PDF page 6 diagram

5.6

Part No. HRS No. RoHS2
C.FLP-HKJ 311-0024-0 ○

Note : The mated portion of the C.FL side has a lower lock retention force than regular products so the adapter cannot be used for purposes other than performance measurements.

■Insertion and Extraction Tool

Tool for mating and unmating the plug.

PDF page 6 diagram
PDF page 6 diagram
Part No. HRS No. RoHS2
X.FL(V)-LP-IN.OUT 331-0076-0 ○

Note : The insertion and extraction tool may be deformed or damages if dropped, etc. so please handle with care.

Page 7

□Usage Precautions

1. Plug

(1) Mating / un-mating ①To un-mate, use the extraction tool X.FL-LP-IN.OUT as shown in the following figure. [How to un-mate a plug] X.FL(V)-LP-IN.OUT Do not un-mate a connector by pulling the cable as it may cause damage to the connector. ②To mate a connector, use the mating side of the plug mating and unmating tool X.FL-LPIN. OUT. Align the mating axes between both connectors and check that the shell is properly aligned. The connector should be inserted perpendicularly as much as possible. (See the following figure) X.FL(V)-LP-IN.OUT
(2) Pull forces on the cable after connectors are mated Once the connector is mated, do not apply a load to the cable in excess of the values indicated in the figure below. C.FL-LP(P)-044 2N Max. C.FL-R-SMT-1 Be careful when lifting the cable as it may add a load or cause unmating. It is recommended to place buffer on the plug when wiring in a direction that causes the cable to lift. (See figure below) Buffer 1.05±0.05
(3)Precautions Do not mate or unmate a connector with an excessive force as it may damage the connector.

Page 8

2. Receptacle

(1) Recommended reflow temperature profile [reference] Soldering profile for lead free solder (reference) 10 sec. or less 250 230 220 (℃) 200 180 Temperature 130 100 50 0 Time (seconds) 50 seconds or less 120 seconds or less Preheat time 60 seconds or less Soldering time 1. The temperatures indicated are the surface temperatures on the printed circuit board at the points of contact with the terminals. 2. Reflow soldering should be performed at peak temperature of 250°C or less at the surface of the printed circuit board. 3. The temperature profile varies depending on conditions such as the size of the printed circuit board, the solder paste type, and solder thickness.
(2) Recommended metal mask thickness 0.1mm
(3) Reflow cycles 2 times

3. Operating Environment and Storage Conditions

(1)Operating environment This product was designed under the assumption that it would be used in a normal operating environment. Use of this connector under adverse environmental conditions such as those described below is not advised and may lead to discoloration or other kinds of degradation. ・Regions having exposure to excessive amounts of fine particles and dust ・Areas with high densities of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive gases. (e.g., exhaust gas from automobiles or factories) ・Environments having a large difference in temperature, such as near a heater.
(2)Storage conditions Store the product in Hirose Electric's packaging or similar packaging conditions. Temperature : -10 to +40°C, humidity : 85% or less (recommended storage conditions) Use the product within six months from delivery. Products for which the storage period has expired must be tested for solderability before the use.

2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN https://www.hirose.com/

The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 01/2022. Contents are subject to change without notice for the purpose of improvements.