DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 4

Technical content

04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog, product data, ‘Definitions’ section, application notes and all specifications are subject to change. n Pin assignment similar to ISO 7588 part 1 n Customized versions on request – 24VDC versions with contact gap >0.8mm – Integrated components (e.g. resistor, diode) – Customized marking/color – Special covers (e.g. notches, release features, brackets) Typical applications Cross carline up to 70A for example: ABS control, cooling fan, energy management, engine control, glow plug, heated front screen, ignition, lamps: front, rear, fog light, main switch/supply relay. Contact Data Contact arrangement 1 form A, 1 form A, 1 form A,

1 NO 1 NO 1 NO

Contact gap - - >0.8mm Rated voltage 12VDC 24VDC 24VDC1) Limiting continuous current 23°C 70A 70A 70A 85°C 50A 50A 50A 125°C 30A 30A 30A Limiting making current2) 240A 240A 240A Limiting breaking current 70A 25A 40A Limiting short-time current overload current, ISO 8820-33) 1.35 x 50A, 1800s 2.00 x 50A, 5s 3.50 x 50A, 0.5s 6.00 x 50A, 0.2s Jump start test, ISO 16750-1 24VDC for 5min, conducting nominal current at 23°C Contact material Silver based Min. recommended contact load4) 1A at 5VDC Initial voltage drop, form A (NO) contact at 10A, typ./max. 10/300mV Frequency of operation at nominal load 6 ops./min (0.1Hz) Operate/release time typ. 7/2ms5) Electrical endurance resistive load at 14VDC >1x105 ops. - - 70A >2x105 ops. - - 50A resistive load at 28VDC - >1x105ops. >1x10 5 ops. 25A 50A Power Relay F7 Plug-in Maxi ISO Relays F134J_a_bw Contact Data (continued) Mechanical endurance >1x107ops. 1) Special high performance 24VDC version with contact gap >0.8mm, part number V23134-A0056-X408 (see part number table). 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Current and time are compatible with circuit protection by a typical automotive fuse. Relay will make, carry and break the specified current. 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at http://relays.te.com/appnotes/ 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Coil Data Rated coil voltage 12VDC, 24VDC Coil versions, DC coil Coil Rated Operate Release Coil Rated coil code voltage voltage voltage resistance6) power 6) VDC VDC VDC Ω±10% W 052 12 7.2 1.6 90 1.6 053 24 14.4 3.2 324 1.8 056 24 16.0 4.0 268 2.1 065 24 14.4 2.4 288 2.0 6) Without components in parallel. All figures are given for coil without pre-energization, at ambient temperature +23°C. Does not take into account the temperature rise due to the contact current E = pre-energization TEVF4_OVR1 Does not take into account the temperature rise due to the contact current E = pre-energization. Coil operating range ECR0629-N Load limit curve: safe shutdown, no stationary arc/make contact. Load limit curve measured with low inductive resistors verified for 1000 switching events. Max. DC load breaking capacity

04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Plug-in Maxi ISO Relays Power Relay F7 (Continued) Insulation Data Initial dielectric strength between open contacts 500Vrms between contact and coil 500Vrms between adjacent contacts 500Vrms Load dump test ISO 7637-1 (12VDC), test pulse 5 Vs=+86.5VDC ISO 7637-2 (24VDC), test pulse 5 Vs=+200VDC Other Data EU RoHS/ELV compliance compliant Protection to heat and fire according UL-94 HB or better7) Ambient temperature -40 to 125°C Climatic cycling with condensation EN ISO 6988 6 cycles, storage 8/16h Temperature cycling, IEC 60068-2-14, Nb 10 cycles, -40/+85°C (5°C/min) Damp heat cyclic, IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55°C Damp heat constant, IEC 60068-2-3, Ca 56 days Category of environmental protection, IEC 61810 RTI – dustproof, RT III – sealed Degree of protection, IEC 60529 IP54 (dustproof), IP67 (sealed) Corrosive gas IEC 60068-2-42 10±2cm3/m3 SO2, 10 days IEC 60068-2-43 1±0.3cm3/m3 H2S, 10 days Vibration resistance (functional) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g8) Shock resistance (functional) IEC 60068-2-27 (half sine) 6ms, min. 30g.8) Drop test, free fall IEC 60068-2-32 1m onto concrete Other Data (continued) Terminal type plug-in, QC/ PCB Cover retention axial force 150N pull force 150N push force 150N Terminal retention pull force 100N push force 100N resistance to bending 10N8) force applied to side 10N8) torque 0.3Nm Weight approx. 38g (1.3oz) Resistance to soldering heat THT IEC 60068-2-20 260°C, 10s Packaging unit plug-in: 210 pcs. plug-in with bracket: 208 pcs. PCB 315 pcs. 7) Refers to used materials. 8) No change in the switching state >1μs. Valid for NC contacts, NO contact values significantly higher. 8) Values apply 2mm from the end of the terminal. When the force is removed, the terminal must not have moved by more than 0.3mm. Accessories For details see datasheet Connectors for Maxi ISO Relays NO 1 form A, NO 3086 NOR 1 form A, NO with resistor 3086 NOD 1 form A, NO with diode 3086 Terminal Assignment

04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog, product data, ‘Definitions’ section, application notes and all specifications are subject to change. Plug-in Maxi ISO Relays Power Relay F7 (Continued) Quick connect terminal similar to ISO 8092- 1 24.9 ±0.3 16 ±0.5 6 ±0.4 15 ±0.1 4 ±0.2 17 +1/-0.5 11 ±0.5 0.8 ±0.05 ø 1.7 +0. 2 1.2 ±0.059.5 ±0.1 6.3 ±0.1 25.9 ±0.3 25.9 ±0.3 5.3 ±0.1 TE1098-Y1 0.3 Measurement reference plane TE1103-411 Dimensions Power Relay F7 with quick connect terminals View of the terminals (bottom view) 26.2 MAX. 3.0 1.5 25.2 MAX. 26.2 MAX. 3.8 TIN PLATED 2.786 TE2104-H1 26.2 MAX. 3.0 1.5 25.2 MAX. 26.2 MAX. 3.8 TIN PLATED 2.786 TE2104-H1 Power Relay F7 with PCB terminals View of the terminals (bottom view) PCB Layout Bottom view on solder pins 17.9 8.4 2x 1.93 17.0 3.8 8.5 3.8 2x 2.18 3.8 3.8 TE2105-Q1

04-2013, Rev. 0413 www.te.com © 2013 Tyco Electronics Corporation, a TE Connectivity Ltd. company. Catalog and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section. Catalog and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at http://relays.te.com/definitions Catalog product data, ‘Definitions’ section, application notes and all specifications are subject to change. Plug-in Maxi ISO Relays Power Relay F7 (Continued) Product code structure Typical product code V23134 -J 0 052 -D642 Type V23134 Power Relay F Contact arrangement J 1 form A, 1 NO Cover

0 Standard 1 Bracket near terminal 30 ISO

056 24VDC (contact gap >0.8mm) 065 24VDC Terminal/arrangement D642 Plug-in/NO Xnnn Customized (nnn: version number) Product code Arrangement Cover Coil suppr. Circuit1) Coil Cont. material Terminals Part number V23134-J0052-D642 1 form A, 1 NO Standard NO 12VDC Silver based Plug-in, QC 7-1393303-3 V23134-J0052-X429 Resistor 680Ω NOR 1-1414147-0 V23134-J0052-X439 Diode (cathode 86) NOD 1-1414286-0 V23134-J0052-X455 Resistor 470Ω NOR PCB 1-1414610-0 V23134-J0052-X511 NO 3-1415001-2 V23134-J0052-X461 Resistor 560Ω NOR Plug-in, QC3) 1-1414469-0 V23134-J0053-D642 NO 24VDC Plug-in, QC 9-1393303-7 V23134-J0056-X4082) Resistor 1200Ω NOR Plug-in, QC3) 0-1393304-5 V23134-J0065-X4974) NO PCB 3-1414937-3 V23134-J1052-D642 Bracket 12VDC Plug-in, QC 0-1393304-9 V23134-J1052-X281 Resistor 560Ω NOR 1-1393304-0 V23134-J1053-D642 NO 24VDC 1-1393304-1 1) See terminal assignment diagrams. 2) Special feature: contact gap >0.8mm. 3) Special feature: 14.5mm load terminals. 4) Packed in tray with 300 pcs. per unit. Other types on request. This list represents the most common types and does not show all variants covered by this datasheet.