2SC2783 TOSHIBA

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 2

Technical content

TOSHIBA TRANSISTOR SILICON NPN EPITAXIAL PLANAR TYPE UHF BAND POWER AMPLIFIER APPLICATIONS Unit in mm @ Output Power : Po=40W (Min.) 330308 (f=470MHz, Vcc =12.5V, Pi=13W) E lil a 3 ) \\ ee 8] + 4) 31Zoy fase a [Is s MAXIMUM RATINGS (Tc = 25°C) S2t035 | 33] (saa 3/3|5 CHARACTERISTIC [SYMBOL qe Collector-Base Voltage Vepo_ | _36 | Vv || “+--+ + Collector Emitter Voltage Vcr Tmitter-Base Voltage VEBO arveere Collector Current A | Collector Power Dissipation 2. EMITTER 5. EMITTER Junction Temperature 3. BASE 6. COLLECTOR Storage Temperature Range —65~175 JEDEC _ TOSHIBA 2-13C1A ELECTRICAL CHARACTERISTICS (Tc = 25°C) Weight : 5.5g CHARACTERISTIC SYMBOL | TEST CONDITION Collector Cut-off Current Icpo___|VcB=15V, In=0 | — | — | 6 | ma] Collector-Base Breakdown Voltage BR) CBO|ICG=10mA, IR=0 [| 36] — | — |v] Collector-Emitter Breakdown Voltage |V (BR) CEO|Ic=50mA, IR=0 [| i¢6f — | —]| Vv] Emitter-Base Breakdown Voltage BR) EBO|In=1mA, Ic=0 [ 4/—|[-—]|[v] DC Current Gain Von=5V.Ig=5A * | 10[ — [150 |_| Collector Output Capacitance Vopei20V, In=0 | = | s10[ 150 | oF | [Output Power | Po Fig) [ 4o[ 45] — | Ww | Voc=12.5V, f=a70mie| 488] 54] — | ab | Collector Efficiency Pi=13W | so] | — | @ | Series Equivalent Input Impedance Voo=12.5V | - | aja |= | 2 | Series Equivalent Output Impedance f=470MHz, Po=40W | — | ‘ja }- [9] * Pulse Test: Pulse Width=100s, Duty Cycle=3% CAUTION Beryllia Ceramics is used in this product. The dust or vapor can be dangerous to humans. Do not break, cut, crush or dissolve chemically. Dispose of this properly according to law. Do not intermingle with normal industrial or domestic waste. ser001eaar malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to observe standards of safety, and to avoid situations in which a malfunction or failure of a TOSHIBA product could cause loss of human life, bodily injury or damage to property. In developing. your, designs, please ensure that TOSHIBA. products are, used within specified operating ranges as set forth in the most recent products specifications. Also, please keep in mind the precautions and conditions set forth in the TOSHIBA Semiconductor Reliability Handbook 1998-07-17 1/2

Fig. Po TEST CIRCUIT Pi C1 C4 Po ZG =500) Z,=500 RFC L Co 1 C3 FB Vcc C6 I C7 Cy~Cq =: ~20pF Ly : ¢1 SILVER PLATED COPPER WIRE, 6ID, 3T C5 : 1000pF RFC : ¢1 ENAMEL COATED COPPER WIRE, 61D, 10T C6 : 10uF BOARD : 1.6mmTEFLONGLASS ¢€R=2.5 C7 : O.1pF FB : FERRITE BEADS Po, 70 — Pi a ge f=470MH2 é je | e = 50) | = An g 4 a 2 7 E g 1) 5 5 49) 7 80 2 Plat i tel |

3 Lz c 0 &

pit | Te 30 60 8 12 16 20 INPUT POWER Pi (W) CAUTION These are only typical curves and devices are not necessarily guaranteed at these curves.

261001 EAA"

CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. @ The information contained herein is subject to change without notice 1998-07-17 2/2