DATASHEET SEARCH SITE

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com TB-3050 Page 1 of 4 © 2013 DESCO INDUSTRIES, INC. Employee Owned Jewel® Workstation Continuous Mini Monitor Operation, Installation and Maintenance

Description

The Jewel® Workstation Continuous Mini Monitor independently monitors the operator and the worksurface. The instant an operator’s wrist strap or cord fails, the monitor will issue audible and visual alarms alerting the user of the problem. In the same manner, the unit also confirms that a path to ground of less than 500 megohms exists from the ESD worksurface. The Jewel ® Workstation Continuous Monitor is a Single Conductor Impedance Sensing Continuous Monitor small AC voltage is used in a detection circuit designed to eliminate false alarms and adjustment. They use the phase difference between current and voltage to detect changes in impedance of the grounding cord, wristband and person. No adjustments are required.” “Typical test programs recommend that wrist straps that are used daily should be tested daily. However, if the products that are being produced are of such value that knowledge of a continuous, reliable ground is needed, and then continuous monioring should be considered or even required.” Advantages Of Continuous Monitoring Over Periodic Testing “When considering constant [or continuous] monitors, the equipment cost including the wrist strap, maintenance and training cost, labor time for performing wrist strap tests, and the potential failures due to non- functional wrist straps should be considered. TECHNICAL BULLETIN TB-3050 April 2013 Figure 1. Desco 19218 Jewel® Workstation Continuous the need for periodic wrist strap tests and logging. position, the operator ground status light will remain red. Monitor will reliably determine if the circuit is complete.

TB-3050 Page 2 of 4 © 2013 DESCO INDUSTRIES, INC. magnetic and electrostatic interference. effects of squeezing or stretching the coil cord. unchanging, and continuous as uninterrupted. / wrist strap unmonitored for over 90% of each cycle.

1 Jewel® Workstation Continuous Mini Monitor

2 Push and Clinch Snaps

1 Certificate of Calibration

bottom of the monitor (see Figure 2). Figure 2. Installation of push and clinch snaps to

DESCO WEST - 3651 Walnut Avenue, Chino, CA 91710 • (909) 627-8178 DESCO EAST - One Colgate Way, Canton, MA 02021-1407 • (781) 821-8370 • Website: Desco.com TB-3050 Page 4 of 4 © 2013 DESCO INDUSTRIES, INC. Employee Owned Hand Lotion. When leaving the area, a person can take the coil cord along or leave it attached to the monitor in park position. NOTE: Removing the banana plug from the monitor’s operator jack will disable the audio alarm. It is recommended that you use the Park Snap rather than continuously removing the Banana Plug from its jack. Doing so will increase the life span of the operator jack. If your process requires the constant insertion and removal of the banana plug, please contact your Desco Representative for alternate solutions. Specifications: Test range of monitored circuit: 500K - 10M ohms† Worksurface Limit*: Set to 500 Megohms ± 20% Operating Voltage: 24VAC, 50-60 Hz Wrist strap open circuit voltage:

1.2 Volts peak to peak @ 1-2 MicroAmps

Mat test open circuit voltage: 5 - 7.5 Volts Response time to alarm: <50 mS Operating Temperature: 32ºF - 100ºF Humidity Range: 0-95% RH, non- condensing Dimensions: 2.77" L x 2.07" W x .71" H † This cannot be verified with standard DC test equipment. The continuous monitor is an impedance sensing device and the limits are determined by the magnitude and angle of the impedance. *Contact factory for special limits. NOTE: Worksurface must have a conductive layer such as Dual Layer Rubber or Dissipative 3-Layer Vinyl or Micastat ® Dissipative Laminate with conductive buried layers. Desco continuous monitors are not recommended for use with homogeneous matting. Maintenance and Calibration The Jewel® Workstation Continuous Mini Monitor is solid state and designed to be maintenance free. It is calibrated to NIST traceable standards. There are no user adjustments necessary. Because of the wave distortion impedance sensing nature of the test circuit, special equipment is required for calibration. We recommend that calibration be performed annually using the Desco 98220 Continuous Monitor Calibration Unit. The Calibration Unit is a most important product which allows the customer to perform NIST traceable calibration on continuous monitors. The 98220 is designed to be used on the shop floor at the workstation, virtually eliminating downtime, verifying that the continuous monitor is operating within tolerances. The 98220 provides a simple and quick means to assure compliance verificaton Per ANSI/ESD S20.20 Table 3 per ESD TR53. Limited Warranty Desco expressly warrants that for a period of one (1) year from the date of purchase Desco Continuous Monitors will be free of defects in material (parts) and workmanship (labor). Within the warranty period, a credit for purchase of replacement Desco Continuous Monitors, or, at Desco’s option, the Continuous Monitor will be repaired or replaced free of charge. If product credit is issued, the amount will be calculated by multiplying the unused portion of the expected one year life times the original unit purchase price. Call Customer Service at 909-627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for Return Material Authorization (RMA) and proper shipping instructions and address. Include a copy of your original packing slip, invoice, or other proof of date of purchase. Any unit under warranty should be shipped prepaid to the Desco factory. Warranty replacements will take approximately two weeks. If your unit is out of warranty, Desco will quote repair charges necessary to bring your unit up to factory standards. Call Customer Service at 909- 627-8178 (Chino, CA) or 781-821-8370 (Canton, MA) for a Return Material Authorization (RMA) and proper shipping instructions and address. Warranty Exclusions THE FOREGOING EXPRESS WARRANTY IS MADE IN LIEU OF ALL OTHER PRODUCT WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WHICH ARE SPECIFICALLY DISCLAIMED. The express warranty will not apply to defects or damage due to accidents, neglect, misuse, alterations, operator error, or failure to properly maintain, clean or repair products. Limit of Liability In no event will Desco or any seller be responsible or liable for any injury, loss or damage, direct or consequent, arising out of the use of or the inability to use the product. Before using, users shall determine the suitability of the product for their intended use, and users assume all risk and liability whatsoever in connection therewith.