MX841 IXYS
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 6
Technical content
Drawing No. 17023 www.ixys.net MX841 White LED Step-Up Converter Features:
- 1.1V to 5.5V Input Range
- 2 Amp Peak Switch Current
- High Efficiency > 80%
- 20V Maximum Output with Over-Voltage Protectio n
- LED Intensity Control
- 1.0 MHz Fixed Frequency Switching
- 8 Lead SOIC Package Applications:
- White LED Display Backlighting - Low Voltage: Mobile Phones, PDA’s, MP3 Players, Digital Cameras - High Drive Current: Vehicle Instrumentation Panels
Ordering Information
Part No. Description Qty 17000-00TU SOIC-8 Standard Tube 100 17000-00TR SOIC-8 Standard T&R 2500 17043-00TU SOIC-8 Exposed Pad Tube 100 17043-00TR SOIC-8 Exposed Pad T&R 2500 General Description The MX 841 i s a fixed f requency, con stant cu rrent source step-up DC/DC converter. The output current is di rectly re gulated ma king the MX8 41 id eal fo r driving series connected white light e mitting diodes (LED’s) i n backlight ap plications. T he MX84 1 powers up to 3 se ries white LED’s at 1.1V, and 20 series/parallel white LED’s at 5.0V. The MX841 features a 1.0MHz switching frequency to accommodate the use of small capacitors and a small i nductor ne cessary i n si ze sensitive porta ble applications. Light i ntensity an d shutdown are conveniently controlled by a single a nalog volta ge. Power effici ency and battery life a re exten ded through the use of a hi gh voltage, lo w R DSON N- channel MOSFET switch. The MX 841 is de signed to op erate ove r a temperature range of -40° C to +8 5°C, an d is available in an SOIC-8 Pa ckage, with or without an Exposed Pa d in Tube or on T ape and Re el. (Alternate package types available upon request). Functional Block Diagram Typical Application MX841CTRL Vbattery VDD SW OVD IsenseCTL/ SLEEP Rsense Vboost Analog GND Switch GND SW 145 osc err amp/ comparator sleep det bias gen VDD driver Isense OVDband gap compare Gnd Switch SWSW CTL/SLEEP AnalogGnd
Absolute Maximum Ratings (Voltages with respect to GND=0V) Parameter Min Max Unit VDD Supply Voltage -0.4 +6.5 V CTRL Voltage GND-0.4 VDD+0.4 V ISENSE Voltage GND-0.4 VDD+0.4 V SW Voltage -0.4 +24.0 V OVD Voltage -0.4 +24.0 V Operating Ambient Temperature Range -40 +85 Co Storage Temperature Range -55 +150 Co Operating Junction Temperature Range -40 +125 Co Standard SOIC θJA = 114°C/W 775 mWPower Dissipation TA = 27°C Exposed Pad SOIC θJA = 50°C/W 1.75 W ESD Warning ESD (e lectrostatic d ischarge) sens itive dev ice. Altho ugh the M X841 fe atures pr oprietary E SD protection c ircuitry, permanent damage may be sustained if su bjected to high energy electrostatic discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of functionality. VDD=3.0V, RSENSE=5Ω, VCTRL=1.0V, L=6.8µH, CBYP=1µF, TA = -40oC to +85oC, Typical Values at +25oC Unless otherwise specified Parameter Condition Min Typ Max Unit Supply Voltage TA = 25 oC 1.1 5.5 V Supply Current Overvoltage Not Switching: VCTRL = 260mV VRSENSE > 13 X VCTRL 0.5 0.8 Supply Current Operating Switching: VCTRL= VDD, VRSENSE=GND 2 mA TA = +25oC 6 µA Sleep Current VCTRL < 100mV TA = +85oC 7 µA CTRL Bias Current -10 µA ISENSE Bias Current -7 µA VCTRL >260mV 20 µA OVD Bias Current OVD = 18V VCTRL = GND 0 OVD Rising 22 V Over Voltage Threshold OVD Falling 18.5 V CTRL / VRSENSE 13 V/V VCTRL Rising 260 mV VCTRL Sleep Mode VCTRL Falling 100 mV VSW = 0.1V 1.9 Ω SW On Resistance VSW = 0.5V 2.2 Ω VDD=1.2V, L=33µH 30 mA Switch Current VDD=5.5V, L=2.5µH 2 A SW Voltage Range VDD - VSCHOTTKY 20 V TA = +25oC 0.1 µA SW Leakage Current OVD = VSW = 18V TA = +85oC 0.3 µA VCTRL 0 VDD V Absolute Maximu m Rat ings ar e stress ratings. Stresses in ex cess of these rati ngs can ca use p ermanent damage to th e dev ice. F unctional operation of the dev ice at these or any other con ditions b eyond thos e indicated in the operational sections of this data sheet is not i mplied. Exposure of the d evice to the absolute maxi mum ratings for an extended p eriod may d egrade th e device and affect its reliability. Preliminary MX841 2 03/10/05 Drawing No. 17023 www.ixys.net
VDD=3.0V, RSENSE=5Ω; VCTRL=1.0V, L=6.8µH; CBYP=1µF, TA = -40oC to +85oC, Typical Values at +25oC Unless otherwise specified Parameter Condition Min Typ Max Unit Oscillator Frequency 0.6 1.0 1.3 MHz Duty Cycle 72.5 % Pin Description Pin No. Pin Name Description 1, 4 SW Power Switch. Connects the drain of the internal high voltage N-channel MOSFET to the Inductor and Schottky Diode to generate the LED boost voltage. This voltage is determined by the total forward bias voltage of the LED series string and the Isense resistor value. (Note: Both pins must be connected.) 2 Analog GND Analog Ground (Note: Must be connected to a low noise ground source.) 3 Switch GND Switch Ground (Note: Must be connected to a high current ground source.) 5 VDD Input supply pin. Input range from 1.1 to 5.5 volts. Must be bypassed with a low ESR capacitor to GND.
6 OVD
Over Voltage Detect input. Compares the LED boots voltage to the internal voltage reference. If the boost voltage rises above 22V the OVD circuit disables the oscillator and N-channel MOSFET until the boost voltage falls below 18.5V. Must be bypassed with a low ESR capacitor to GND.
7 CTRL
Shutdown and Intensity Control Input. A control voltage above 260mV enables device operation. A control voltage below 100mV disables device operation. LED intensity is linearly adjusted with voltages between 260mV and VDD.
8 Isense
Current Sense Input. The LED bias current is set by connecting a carbon composite or monolithic resistor from this input to Ground. ISENSE regulates this current to 1/13 of the CTRL input voltage. Preliminary MX841 3 03/10/05 Drawing No. 17023 www.ixys.net
The MX841 is spe cifically design ed to be operated fro m a single cell battery so urce. The step-up volt age ne cessary for the con stant current s ource to d rive up to 5 w hite L ED’s in series, or m ultiple strings of white LED’s, is achieved with minimal external components. (See Application Schematics on pages 1&4). Setting the LED Current The regulated output current is determined by the selection of the se nse Resistor co nnected from the ISENSE input to ground, and the maximum user defined volta ge of th e CTRL i nput. T he de sired output current, (typically 15mA to 20mA for white LEDs), is derived using the following formula for the RSENSE value: RSENSE Ω = (VCTRL X 1/13) / ILED. Current Regulation / Light Intensity Control The I SENSE voltage is fed into an ErrorAmp/Comparator. Th e use r define d Control Voltage applied at the CT RL input is scale d by a gain fa ctor o f 1/13 and compa red to t he I SENSE voltage. If th e scal ed control voltage i s g reater than the I SENSE voltage, the 1.0M Hz o scillator signal drivin g the N-Cha nnel MOSFE T will be enabled. On ce the I SENSE voltage re aches th e scaled CTRL voltage the oscillato r signal i s modulated on a nd off by the ErrorAmp/Comparator to maintain th e de sired regulated output current. Light inten sity is control led by redu cing the voltage at th e CTRL inp ut. As the CTRL i nput voltage is redu ced b elow the u ser defined maximum val ue, the o scillator signal d riving the N-Channel MOSFET is interrupted by the ErrorAmp/Comparator. The pulse skip modulating of the N-Channel MOSFET causes a reduction in the regul ated cu rrent equal to th e ratio of th e reduced CT RL voltage t o the maximum CT RL voltage. Sleep Mode The MX841 goes into sleep mode when the VCTRL input is less than 100mV. All circuits except VCTRL detection are shutd own a nd the supply current falls to 6uA. Onc e the V CTRL input rises ab ove 260mV the MX841 resumes normal operation. Over Voltage Detection The MX841 will go into a shutdown state to avoid an ove r volt age condition if the current p ath between the SW output a nd the R SENSE input is interrupted. A voltage reference and compa rator circuit evaluates the voltage potential at the OVD input an d shuts d own the o scillator and N- Channel MOSFET if an over voltage condition is detected. Normal operation is resumed once the OVD i nput voltage fall s belo w th e refe rence voltage, (20V typical). Drawing No. 17023 www.ixys.net
Circuit Application Driving 15 White LED’s MX841CTRL Vbattery 3.0V - 5.0V VDD SW OVD IsenseCTL/SLEEP Rsense Vboost 1N5817 VF=0.3V 6.8uH Ipk=1.7A 20K Ohms 22uF 35V 0.1uF in Parallel
5 Ohms 5 Ohms 5 Ohms
0.1uF in Parallel 26K Ohms @ 3.0V 57K Ohms @ 5.0V (Dimming Control) SW Analog GND Switch GND IXYS Cor poration makes no representations or warranties w ith r espect to the accurac y or compl eteness of the contents of this publication and reserves the right to make changes to specif ications and product descrip tions at a ny time w ithout notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as se t forth in IXYS’ Standard Terms and Conditions of Sale, IXYS Corporatio n assumes no l iability whatsoever, and disclaim s any e xpressed or implied w arranty, relating t o its products including, but n ot limited to, th e implied w arranty of merchant ability, fitness for a particular purpose, or infrin gement of an y intellectual property right. Preliminary MX841 5 03/10/05 Drawing No. 17023 www.ixys.net 8-LEAD SOI
3540 Bassett Street
Santa Clara, CA 925054 Tel: 1-408-892-0700 Fax: 1-408-496-0670 e-mail:sales@ixys.net SALES OFFICES AMERICAS Eastern Region [AL, AR, CT, DC, FL, GA, IA, IL, IN, KS, KY, LA, MA, MD, ME, MI, MN, MO, MS, NC, ND, NE, NH, NJ, NY, OH, OK, PA, RI, SC, SD, TN, TX, VA, VT, WI, WV, Americas: Canada, Brazil] IXYS Groveland, FL Tel: 1-352-429-3892 Fax: 1-352-429-3899 mproctor@clare.com Western Region [AK, AZ, CA, CO, HI, ID, MT, NM, NV, OR, UT, WA, WY, Americas: Canada, Mexico] IXYS Santa Clara, CA 95054 Tel: 1-408-982-4353 Fax: 1-408-496-0670 EUROPE European Headquarters IXYS Semiconductor GMBH Edisonstrasse 15 D- 68623 Lampertheim Germany Tel : +49-6206-503203 Fax - +49-6206-503286 SALES OFFICES France Eurocomposant 144, Av. J. Kessel F-78960 Voisins-le-Bretonneux, France Tel : +33-130-649515 Fax : +33-130-436827 Germany IXYS Semiconductor GMBH Edisonstrasse 15 D- 68623 Lampertheim Germany Tel : +49-6206-503203 Fax - +49-6206-503286 Italy IXYS Via C. Colombo 10/A I-20066 Melzo (Milano) Tel: +39-02-95737160 Fax: +39-02-95738829 Sweden IXYS Sales Comptronic AB Box 167 S-16329 Spånga Tel: +46-862-10370 Fax: +46-862-10371 United Kingdom IXYS UK Sales Marco Polo House Cook Way Bindon Road Taunton, Somerset TA2 6BG Tel: +44-1-823 352541 Fax: +44-1-823 352797 ASIA / PACIFIC Asian Headquarters IXYS Room 1016, Chia-Hsin, Bldg II, 10F, No. 96, Sec. 2 Chung Shan North Road Taipei, Taiwan R.O.C. Tel: 886-2-2523-6368 Fax: 886-2-2523-6368 IXYS ca nnot a ssume responsibility f or u se of a ny circu itry o ther th an circu itry entirely embodied in this IXYS product. No circuit patent licenses nor indemnity are expressed or implied. IXYS reserves the right to change the specification and circuitry, without notice at any time. The products described in this document are not i ntended for use i n medi cal i mplantation or ot her di rect life su pport applications where malfunction may result in direct physical harm, injury or death to a person. Specification: MX841 ©Copyright 2005, IXYS Corporation All rights reserved. Printed in USA. Drawing No. 17023 www.ixys.net