1623368 PHOENIX

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 9

Technical content

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 1 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Please be informed that the data shown in this PDF Document is generated from our Online Catalog. Please find the complete data in the user's documentation. Our General Terms of Use for Downloads are valid (http://phoenixcontact.com/download) Device connector, front mounting, SB, angled rotatable, shielded: yes, for standard and SPEEDCON interlock, M40, No. of pos.: 4+4+4+PE, Direction of rotation: Standard, type of contact: Pin, Crimp connection, Axial O- ring, 4x Ø4,2, coding:CAT5, coding 1 Your advantages Easy connection, thanks to infinitely adjustable cable outlet direction up to 310° Transmission of signals, data, and power in just a single connector CAT5 data interface for up to 100 Mbps Mechanical coding reliably prevents incorrect connections Safe use in the field, thanks to high degree of protection Consistent EMC protection for reliable connection solutions in the industrial environment Key Commercial Data Packing unit 1 pc GTIN GTIN 4055626194929 Technical data Temperature range Ambient temperature -40 °C ... 115 °C (see derating curve) Standards and Regulations Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.

  • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
  • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 2 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Technical data Standards and Regulations relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.

  • The products are suitable for applications in plant, controller, and electrical device engineering.
  • When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
  • Assembled products may not be manipulated or improperly opened.
  • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
  • When using the product in direct connection with third-party manufacturers, the user is responsible.
  • For operating voltages > 50 V AC, conductive connector housings must be grounded applicable when combining several circuits in a cable and/or connector
  • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
  • Only use tools recommended by Phoenix Contact
  • The installation notes/Design In documents online on the download page at phoenixcontact.com/products must be observed for this product.
  • Use a protective cap to protect connectors that are not in use. The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products
  • Operate the connector only when it is fully plugged in and interlocked.
  • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
  • Observe the minimum bending radius of the cable. Lay the cable without twisting it.
  • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Data of the insulating body Coding CAT5, coding 1 Contact connection method Crimp connection Type of contacts Pin Application Hybrid Number of positions 13 Direction of rotation Standard Contact diameter of power contacts 3.6 mm Litz wire cross section of power contacts min. 1 mm² Litz wire cross section of power contacts max. 10 mm² Rated current for power contacts 70 A

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 3 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Technical data Data of the insulating body Note for max. connection cross section Rated voltage 630 V AC Rated surge voltage 6 kV Overvoltage category III Degree of pollution 3 Rated voltage (II/3) power contact 850 V DC Rated voltage (III/3) power contact 630 V AC Contact diameter of signal contacts 1 mm Litz wire cross section of signal contacts min. 0.06 mm² Litz wire cross section of signal contacts max. 1.5 mm² Nominal current per signal contact 8 A Note for max. connection cross section Rated voltage of signal contact 500 V Rated surge voltage 1.5 kV Overvoltage category III Degree of pollution 3 Rated voltage (III/3) signal contact 500 V Contact diameter, data contacts 0.8 mm Litz wire cross section, data contacts, min. 0.08 mm² Litz wire cross section, data contacts, max. 0.5 mm² Rated current of each data contact at 25°C 3.6 A Note for max. connection cross section Rated voltage of data contact 50 V Rated surge voltage 1.5 kV Housing data Housing material Turned parts: copper zinc alloy (CuZn), die-cast parts: zinc (GD-Zn) Type of locking for standard and SPEEDCON interlock Degree of protection (when plugged in) IP68/IP69K Thread type M40 Environmental Product Compliance REACh SVHC Lead 7439-92-1 China RoHS Environmentally Friendly Use Period = 50 years For details about hazardous substances go to tab “Downloads”, Category “Manufacturer's declaration” Drawings

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 4 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Dimensional drawing 4xM4 ±0,5 ±0,1 Installation dimensions Schematic diagram A BC D 2 3 8 765 Pin assignment of pin CAT5, coding 1 Diagram 0 10 20 30 40 50 60 70 80 90 100 110 I [A]  [°C] = 3x16 mm 120 I = current strength, ϑ = ambient temperature, power contacts A–C: 3x up to 70 A, signal contacts: 4x 2 A constant, data contacts: no load Dimensional drawing 104,7 66,3 4,4 M40x1,5 4xØ4,4 97,1 A 155° 155° X Pin version: dimension A = 3.7 mm, socket version: dimension A = 0.05 mm, X = reference position for angle of rotation

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 5 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Classifications eCl@ss eCl@ss 10.0.1 27440102 eCl@ss 11.0 27440102 eCl@ss 4.0 27260700 eCl@ss 4.1 27260700 eCl@ss 5.0 27260700 eCl@ss 5.1 27260700 eCl@ss 6.0 27260700 eCl@ss 7.0 27440102 eCl@ss 9.0 27440102 ETIM ETIM 7.0 EC002635 UNSPSC UNSPSC 18.0 39121413 UNSPSC 19.0 39121413 UNSPSC 20.0 39121413 UNSPSC 21.0 39121413 Approvals Approvals Approvals cULus Recognized / EAC Ex Approvals Approval details cULus Recognized http://database.ul.com/cgi-bin/XYV/template/LISEXT/1FRAME/index.htm 20170915-E468743 Nominal voltage UN 600 V Nominal current IN 35 A mm²/AWG/kcmil 8

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 6 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Approvals EAC B.01687 Accessories Accessories Circular connectors (device side) Metal protective cap - SB-Z0002 - 1623828 Metal protection cap with steel wire for M40 connectors with external thread Crimp contact Crimp contact - SF-08KP010 - 1621574 Crimp contact - SF-08KP020 - 1621575 Crimp contact - SB-10KP001 - 1623607

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 7 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Accessories Crimp contact - SB-10KP002 - 1623611 Crimp contact - SB-10KP003 - 1623612 Crimp contact, turned, Single contact, contact diameter: 1 mm, crimp range: 0.5 mm² ... 1 mm² Crimp contact - SB-10KP004 - 1623613 Crimp contact, turned, Single contact, contact diameter: 1 mm, crimp range: 1 mm² ... 1.5 mm² Crimp contact - SB-36KP002 - 1623383 Crimp contact - SB-36KP003 - 1623384 Crimp contact, turned, Single contact, contact diameter: 3.6 mm, crimp range: 4 mm² ... 6 mm²

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 8 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Accessories Crimp contact - SB-36KP004 - 1623385 Crimp contact, turned, Single contact, contact diameter: 3.6 mm, crimp range: 10 mm² ... 10 mm² Mounting material Protective cap - SM-Z0001 - 1605866 Plastic protection cap for connectors with M40 external thread Color-coding - SM-Z0028 - 1620627 Color-coding, color: green Color-coding - SM-Z0029 - 1620628 Color-coding, color: orange Color-coding - SM-Z0030 - 1620629 Color-coding, color: black Protective cover

https://www.phoenixcontact.com/pi/products/1623368 02/04/2022 Page 9 / 9 Device connector, front mounting - SB-8EPCA8AA700S - 1623368 Accessories Metal protective cap - SB-Z0001 - 1623827 Metal protection cap for M40 connectors with external thread Phoenix Contact 2022 © - all rights reserved http://www.phoenixcontact.com PHOENIX CONTACT GmbH & Co. KG Flachsmarktstr. 8

32825 Blomberg

Tel. +49 5235 300 Fax +49 5235 3 41200 http://www.phoenixcontact.com