15-004643 CONEC

Document overview

  • Manufacturer or author: Provided By www.digicamel.com(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 2

Technical content

( 5 : 1 ) AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD EE EE EE EE FF FF FF FF AA AA AA AA BB BB BB BB CC CC CC CC DD DD DD DD 15-00464 CONEC ABC o dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1105 D-SUB COMBINATION MALE see notes Henneboel02.08.12

02.08.12 Fischer

2:1 (5:1) 15-00464 a Original 21,1 -00,3 25,14 - 0,02 0,23+ 33,32 - 0,12 0,13+ 47,7 - 0 0,3+ 4-40 UNC 4-40 UNC 8,23 - 0 0,25+ 3,6 -00,25 -0,18 0,12 SEALING COMPOUND RUBBER GASKET PLACED ON TOP SURFACE OF MALE INSULATOR see note 14 O-RING o (see note 10) 17,53 -0,3 0,4 2,7n (2x) 9,4 4,8SW 4,6 10° 1,12n (5x) POS. A1 POS. 1 NOTES: 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST; min. 50µin NICKEL P LATING over COPPER 5. INSULATOR: PBT GF UL 94 V-0, GREEN 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. RUBBER GASKET: TPE 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0; BLACK 9. SIGNAL CONTACTS: COPPER ALLOY PLATING (SEE PART NO): 30µin HARD GOLD over min. 50µin NICKEL if 1 o in PART NO. GOLD FLASH over NICKEL if 3 o in PART NO: SOLDER CUP ACCEPTS CABLE AWG 20 10. HIGH POWER CONTACTS 20A: COPPER ALLOY PLATING MATING SIDE (SEE PART NO): o PLEASE ADD 1 for 30µin HARD GOLD over min. 50µin NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL PLATING TERMINATION SIDE: GOLD FLASH over NIC KEL SOLDER CUP ACCEPTS CABLE AWG 12-14 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. RECOMMENDED PANEL CUT-OUT ON SHEET 2 13. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 14. CONNECTOR IS PART MARKED: 15-00464 o CONEC ABC AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. Directive 2002/95/EC RoHS compliant 10,36 -0,3 0,4

dim. in mm RR RR date drawn THIS DRAW ING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH d-old norm appd. tolerance material: title: dwg no: DIN- sh: part no: namedate namedescriptionrev.DO NOT ALTER CAD DRAWING BY HAND scale: 15K1A1105 PANEL CUT-OUT see sheet 1 Henneboel02.08.12 D-SUB COMBINATION MALE 7W2P Solder cup; with hexlocking screw 3:1 see sheet 1 a Original 3,1 0,05 n (2x) B 33,32\ 0,1 10°\ 1° 28,8\` 0,1 11,4 0,1 i 0,26 A A i 0,26 B3,4 R 0,13 RECOMMENDED PANEL CUT-OUT Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Signal Contact 3.1. Operate the soldering iron at 350° C, 50 Watt max. and use a pencil tip. 3.2. Put tip to wire in solder cup. 3.3. After 1 second bring in solder. 3.4. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 4. Power Contact 4.1. Operate the soldering iron at 350° C, 100 Watt max. and use a pencil tip. 4.2. Put tip to wire in solder cup. 4.3. After 1 second bring in solder. 4.4. Heat for 5 seconds longer. Do not heat contact more than 6 seconds in total. 5. Remove soldering iron. 6. Wait until solder gets rigid again. 7. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up.