1551532 PHOENIX

Document overview

  • Manufacturer or author: Provided By digicamel.com
  • PDF pages: 9

Technical content

Please be informed that the data shown in this PDF document is generated from our online catalog. Please find the complete data in the user documentation. Our general terms of use for downloads are valid. Device connector, rear mounting, PROFINET, 4-position, Pin, straight, M12-SPEEDCON, coding: D, on free cable end, Rear mounting, Pg9, Individual wires, cable length: 0.5 m, 0.34 mm2, TPE litz wire, Alternative product in accordance with RoHS II without Exemption 6c (Pb <0. 1%) item no.: 1239988 Commercial data Item number 1551532 Packing unit 1 pc Minimum order quantity 1 pc Sales key AB24 Product key ABQCGE Catalog page Page 46 (C-2-2019) GTIN 4046356153607 Weight per piece (including packing) 23.1 g Weight per piece (excluding packing) 22.6 g Customs tariff number 85444290 Country of origin DE SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 1 (9)

General The electrical and mechanical data specified assume that the connector pair is correctly locked and mounted. If the connector is unlocked and if there is a danger of contamination, the connector must be sealed using a protective cap > IP54. Influences arising from litz wires, cables or PCB assembly must also be taken into consideration. General Lock nut is included in the scope of delivery General Contact connection method: Crimp connection Safety note WARNING: The connectors may not be plugged in or disconnected under load. Ignoring the warning or improper use may damage persons and/or property.

  • WARNING: Commission properly functioning products only. The products must be regularly inspected for damage. Decommission defective products immediately. Replace damaged products. Repairs are not possible.
  • WARNING: Only electrically qualified personnel may install and operate the product. They must observe the following safety notes. The qualified personnel must be familiar with the basics of electrical engineering. They must be able to recognize and prevent danger. The relevant symbol on the packaging indicates that only personnel familiar with electrical engineering are allowed to install and operate the product.
  • The products are suitable for applications in plant, controller, and electrical device engineering.
  • When operating the connectors in outdoor applications, they must be separately protected against environmental influences.
  • Assembled products may not be manipulated or improperly opened.
  • Only use mating connectors that are specified in the technical data of the standards listed (e.g. the ones listed in the product accessories online at phoenixcontact.com/products).
  • When using the product in direct connection with third-party manufacturers, the user is responsible.
  • For operating voltages > 50 V AC, conductive connector housings must be grounded
  • Ensure that when laying the cable, the tensile load on the connectors does not exceed the upper limit specified in the standards.
  • Observe the corresponding technical data. You will find information: o On the product o On the packing label o In the supplied documentation o Online at phoenixcontact.com/products under the product
  • Only use tools recommended by Phoenix Contact
  • Use a protective cap to protect connectors that are not in use. Safety note SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 2 (9)

The suitable accessories are available online in the accessory section of the product at phoenixcontact.com/products

  • Ensure that the protective or functional ground has been properly connected. are applicable when combining several circuits in a cable and/or connector
  • The connector warms up in normal operation. Depending on the ambient conditions, the surface of the connector can continue to warm up. In this case, the user is responsible for posting warnings (e.g. DIN EN ISO 13732-1:2008-12). Mounting Mounting type Rear mounting Pg9 With flat nut Assembly instructions With flat nut Connection method Individual wires Product properties Product type Circular connectors (device side) Sensor type PROFINET Number of positions 4 No. of cable outlets 1 Shielded no Coding D Thread type M12 Insulation characteristics Overvoltage category III Degree of pollution 3 Material specifications Flammability rating according to UL 94 V0 Seal material NBR Contact material CuZn Contact surface material Au Contact carrier material PA 6.6 Material for screw connection Zinc die-cast, nickel-plated Conductor material Tin-plated Cu litz wires Electrical properties Rated surge voltage 6 kV AC Contact resistance ≤ 3 mΩ Insulation resistance ≥ 100 MΩ

630 V (AC)Nominal voltage UN

250 V (DC)

SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 3 (9)

Max. conductor resistance 57.6 mΩ/m Connection data Conductor connection Connection method Individual wires Contact connection type Pin Conductor cross section 0.34 mm²

2 NmTightening torque

Insertion/withdrawal cycles > 100 Connector Connection 1 Head design Pin Head cable outlet straight Head thread type M12 Head locking type SPEEDCON Coding D Connection 2 Head design free cable end Cable/line Cable length 0.5 m Cable type TPE litz wire Signal type/category PROFINET Wire diameter incl. insulation 1.2 mm ±0.07 mm Single wire, color yellow, orange, white, blue Cable cross section 0.34 mm² Conductor material Tin-plated Cu litz wires Conductor structure signal line 7x 0.25 mm AWG signal line 22 Material wire insulation TPE Thickness, insulation 0.21 mm Nominal voltage, cable 300 V Test voltage, cable 2000 V AC Cable resistance ≤ 57.6 mΩ/m Cable insulation resistance ≥ 20 MΩ*km -40 °C ... 85 °C (cable, fixed installation)Ambient temperature (operation) SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 4 (9)

-25 °C ... 85 °C (Cable, flexible installation) Environmental and real-life conditions Ambient conditions IP67 (When plugged in) IP65 (When plugged in) Degree of protection IP65/IP67 -25 °C ... -85 °C -40 °C ... 85 °C (without mechanical actuation) -25 °C ... 85 °C (Cable, flexible installation) Ambient temperature (operation) -40 °C ... 85 °C (cable, fixed installation) Standards and regulations M12 Standard designation M12 connector Standards/specifications based on IEC 61076-2-111 SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 5 (9)

Pin assignment M12 male connector, 4-pos., D-coded, male side SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 6 (9)

To download certificates, visit the product detail page: https://www.phoenixcontact.com/us/products/1551532  UL Recognized Approval ID: E118976-20100522 Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2

250 V 4 A - 22 -

 cULus Recognized Approval ID: E221474-20140616 Nominal voltage UN Nominal current IN Cross section AWG Cross section mm2

250 V 4 A 22 - 20 -

SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 7 (9)

ECLASS-11.0 27440102 ECLASS-12.0 27440116 ECLASS-13.0 27440116 ETIM ETIM 9.0 EC002635 UNSPSC UNSPSC 21.0 39121400 SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 8 (9)

Environmental product compliance REACh SVHC Lead 7439-92-1 Environmentally Friendly Use Period = 50 yearsChina RoHS For information on hazardous substances, refer to the manufacturer’s declaration available under “Downloads” Phoenix Contact 2024 © - all rights reserved https://www.phoenixcontact.com Phoenix Contact USA

586 Fulling Mill Road

Middletown, PA 17057, United States (+717) 944-1300 info@phoenixcon.com SACC-DSI-MSD-4CON-PG9/0,5 SCO - Device connector, rear mounting 1551532 https://www.phoenixcontact.com/us/products/1551532 Jan 15, 2024, 7:19 AM Page 9 (9)