DATASHEET SEARCH SITE
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 28
Technical content
Once the I2t value for the application waveform has been determined, it must be derated based on the number of cycles expected over the system lifetime. Since the stress induced by the current pulse is mechanical in nature, the number of times the stress is applied has significant bearing on how much derating must be applied to the fuse rating. Figure 5 presents the current pulse derating curve for our surface-mount chip fuses up to 100,000 cycles. Fuse Selection Flowchart However, the basic considerations for fuse selection are shown in the flowchart presented in Figure 6. Following this flow chart will help you select a fuse best suited for your application conditions. Surface-mount Fuse Pulse Derating Curve 100 1000 10000 100000 100% 10% Number of Pulses % of Minimum I2t Figure 5 Step 1 – Determine Steady State Fuse Current Rating Step 2 – Determine Pulse Waveform by Calculating I Step 3 – Apply Pulse Cycle Derating Step 4 – Apply Pulse Temperature Derating Step 5 – Apply Derating for Variance in the Circuit Step 6 – Select Fuse Current Rating for Pulse Environment Step 7 – Select Fuse Current Rating (use higher value between Step 1 and Step 6) Step 8 – Check Voltage Rating Apply Standard Steady State Derating (75%) fuse ≥ Isys/0.75] Apply Temperature Derating [Ifuse ≥ Isys/0.75/Ktemp] Steady State Fuse Current Rating Figure 6 Selecting Surface-mount Fuses Fuse selection seems straightforward, in that, you pick one which has a current rating just a bit higher than your worstcase system operating current. Unfortunately, it’s not that simple. There are derating considerations for operating current and application temperature. Turn-on and other system operations (like processor speed changes or motor start up) cause current surges or spikes that also require consideration when selecting a fuse. So selecting the right fuse for your application is not as simple as knowing the nominal current drawn by the system. Temperature Derating A fuse is a temperature sensitive device. Therefore, operating temperature will have an effect on fuse performance and lifetime. Operating temperature should be taken into consideration when selecting the fuse current rating. The Thermal Derating Curve for surface mount fuses is presented in Figure 4. Use it to determine the derating percentage based on operating temperature and apply it to the derated system current. 1206/0603/0402 Series T emperature Effect on Current Rating
2410 Series
T emperature Effect On Current Rating -55 -55 -35 -15 5 25 45 65 85 105 125-35 -15 5 25 45 65 85 105 145125 105 100 110 105 100 Maximum Operating T emperature (°C) Maximum Operating T emperature (°C) % De-rating % De-rating Figure 4
Surface-mount Fuses– Pulse Tolerant Chip Fuses Pulse Tolerant chip fuses has high inrush current withstand capability and provide overcurrent protection on DC power systems. Silver fusing element, monolithic and multilayer design provides strong arc suppression characteristics. These RoHS-compliant surface-mount devices facilitate the development of more reliable, high performance consumer electronics such as laptops, multimedia devices, cell phones, and other portable electronics.
- High inrush current withstanding capability
- Ceramic Monolithic structure
- Silver fusing element and silver termination with nickel and tin plating
- Excellent temperature stability
- Strong arc suppression characteristics
- Lead free materials and RoHS compliant
- Halogen free (refers to: Br/H11349900ppm, Cl/H11349900ppm, Br+Cl/H113491500ppm)
- Monolithic, multilayer design
- High-temperature performance
- -55°C to +125°C operating temperature range
- Laptops
- Digital cameras
- Cell phones Benefits Features
Applications
- Printers
- DVD players
- Portable electronics
- Game systems
- LCD monitors
- Scanners Surface-mount Fuses Pulse Tolerant Chip Fuses NEW NENENENENENENENENENENENEWWWWWWWWWWWWNEW
78 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours (min.) 200% 1 seconds (min.) 60 seconds (max.) 1000% 0.0002 second (min.) 0.02 seconds (max.) 0603SFP100F/32-2 1.0 0.210 0.080 32 50 0603SFP150F/32-2 1.5 0.101 0.11 32 50 0603SFP200F/32-2 2.0 0.057 0.24 32 50 0603SFP250F/32-2 2.5 0.042 0.56 32 50 0603SFP300F/32-2 3.0 0.030 0.72 32 50 0603SFP350F/32-2 3.5 0.022 1.10 32 50 0603SFP400F/32-2 4.0 0.018 2.08 32 50 0603SFP450F/32-2 4.5 0.014 2.63 32 50 0603SFP500F/32-2 5.0 0.013 3.25 32 50 1206SFP100F/63-2 1.0 0.340 0.11 63 50 1206SFP150F/63-2 1.5 0.150 0.33 63 50 1206SFP200F/63-2 2.0 0.090 0.80 63 50 1206SFP250F/32-2 2.5 0.070 1.19 32 50 1206SFP300F/32-2 3.0 0.035 1.35 32 50 1206SFP350F/32-2 3.5 0.029 1.84 32 50 1206SFP400F/32-2 4.0 0.023 2.74 32 50 1206SFP450F/32-2 4.5 0.021 3.20 32 50 1206SFP500F/32-2 5.0 0.017 5.50 32 50 * Measured at/H1134910% of rated current and 25°C ambient temperature. † Melting I2t at 0.001 sec clear time. 0603 (1608 mm) Pulse Tolerant Chip Fuses 1206 (3216 mm) Pulse Tolerant Chip Fuses A B C D Shape and Dimensions mm (Inch) Table FP1Clear Time Characteristics for Pulse Tolerant Chip Fuses Table FP2 Typical Electrical Characteristics and Dimensions for Pulse Tolerant Chip Fuses Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† T ypical
Electrical Characteristics
Max. Interrupt Ratings Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† T ypical Max. Interrupt Ratings ABCD Min Max Min Max Min Max Min Max ABCD Min Max Min Max Min Max Min Max A B C D Shape and Dimensions mm (Inch)
Surface-mount Fuses– Pulse Tolerant Chip Fuses RoHS Compliant, ELV Compliant HF Halogen Free ClearTime (s) 100 0.1 0.01 0.001 0.0001 10 1001 Current (A) 0603SFP AverageTime Current Curves 1.0A 1.5A 2.0A 2.5A 3.0A3.5A4.0 A 4.5A 5.0A Figure FP1 I2t (A2s) 10,000 1000 100 0.1 0.01 0.010.001 100.1 1 1000.0001 Time (s) 0603SFP I2T vs. t Curves 1.0A 1.5A 2.0A 2.5A 3.0A 3.5A 4.0A 4.5A5.0A Figure FP2 Note:Curves are nominal Figure FP1-FP4 Family Performance Curves for Pulse Tolerant Chip Fuses
80 RoHS Compliant, ELV Compliant HF Halogen Free
ClearTime (s) 10,000 100 0.01 0.001 10 1001 Current (A) 1206SFP AverageTime Current Curves 1.0A 1.5A 2.0A 2.5A 3.0A3.5 A 4.0 A 4.5A 5.0A Figure FP3 I2t (A2s) 10,000 100 0.01 0.01 1 100 10,0000.0001 Time (s) 1206SFP I2T vs. t Curves 1.0A 1.5A 2.0A 2.5A 3.0A 3.5A 4.0A 4.5A5.0A Figure FP4 Note:Curves are nominal /barb4rightPlease go to page 97 for more information for PulseT olerant Chip Fuses. Figure FP1-FP4 Family Performance Curves for Pulse Tolerant Chip Fuses Cont’d
Surface-mount Fuses– 0603 Very Fast-Acting Chip Fuses Very Fast-acting chip fuses help provide overcurrent protection on systems using DC power sources up to 32V DC . The fuse’s monolithic, multilayer design provides the highest hold current in the smallest footprint, reduces diffusion-related aging, improves product reliability and resilience, and enhances high-temperature performance in a wide range of circuit designs. These RoHS-compliant surface-mount devices offer strong arc suppression characteristics and facilitate the development of more reliable, high performance consumer electronics such as laptops, multimedia devices, cell phones, and other portable electronics.
- Very fast acting at 200% and 300% overloads
- Excellent inrush current withstanding capability at high overloads
- Thin body for space limiting applications
- Glass ceramic monolithic structure
- Silver fusing element and silver termination with nickel and tin plating
- RoHS compliant and lead-free materials
- Symmetrical design with marking on both sides (optional)
- Lead free materials and RoHS compliant
- Halogen free (refers to: Br/H11349900ppm, Cl/H11349900ppm, Br+Cl/H113491500ppm)
- Monolithic, multilayer design
- High-temperature performance
- -55°C to +125°C operating temperature range
- Laptops
- Digital cameras
- Cell phones Benefits Features
- Printers
- DVD players
- Portable electronics
- Game systems
- LCD monitors
- Scanners Surface-mount Fuses
0603 Very Fast-Acting Chip Fuses
NENENENENENENENENENENENEWWWWWWWWWWWWNEW
82 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours (min.) 200% 0.01 second (min.) 5 seconds (max.) 300% 0.001 second (min.) 0.2 seconds (max.) 0603SFV050F/32-2 0.5 0.860 0.0093 32 50 0603SFV075F/32-2 0.8 0.450 0.0191 32 50 0603SFV100F/32-2 1.0 0.280 0.0360 32 50 0603SFV125F/32-2 1.3 0.205 0.0630 32 35 0603SFV150F/32-2 1.5 0.143 0.0950 32 35 0603SFV175F/32-2 1.8 0.095 0.1400 32 35 0603SFV200F/32-2 2.0 0.073 0.2100 32 35 0603SFV250F/32-2 2.5 0.046 0.3000 32 35 0603SFV300F/32-2 3.0 0.039 0.4600 32 35 0603SFV350F/32-2 3.5 0.028 0.7300 32 35 0603SFV400F/32-2 4.0 0.023 1.1500 32 35 0603SFV450F/32-2 4.5 0.019 1.6800 32 35 0603SFV500F/32-2 5.0 0.015 2.6200 32 35 * Measured at 10% of rated current and 25°C Part Number 0603 (1608 mm) Very Fast-Acting Chip Fuses A B C D Shape and Dimensions mm (Inch) Table FV1Clear Time Characteristics for Very Fast-Acting Chip Fuses Table FV2Typical Electrical Characteristics and Dimensions for Very Fast-Acting Chip Fuses Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec) T ypical Electrical CharacteristicsMax. Interrupt Ratings /barb4rightPlease go to page 97 for more information for Very Fast-Acting Chip Fuses. 1 10010 ClearTime (s) 100 0.1 0.01 0.001 0.0001 Current (A) 0603SFV AverageTime Current Curves 0.05A 0.75A 1.0 1.25A 1.50A 1.75A2.00A 2.5 3.00 A 3.50A4.00A4.50A 5.00A 0603SFV I²t vs. t Curves I²t (A²s) Time (s) 1000 100 0.1 0.01 0.001 0.0001 0.0001 0.001 0.10.01 1 10 5.00A 4.50A 4.00A 3.50A 3.00A 2.50A 2.00A 1.75A 0.75A 0.05A 1.25A 1.50A 1.00A Figure FV2Figure FV1 Note:Curves are nominal Figure FV1-FV2Family Performance Curves for Very Fast-Acting Chip Fuses ABCD Min Max Min Max Min Max Min Max
Surface-mount Fuses– Fast-Acting Chip Fuses Fast-acting chip fuses help provide overcurrent protection on systems using DC power sources up to 63VDC . The fuse’s monolithic, multilayer design provides the highest hold current in the smallest footprint, reduces diffusion- related aging, improves product reliability and resilience, and enhances high-temperature performance in a wide range of circuit designs. These RoHS-compliant surface-mount devices offer strong arc suppression characteristics and facilitate the development of more reliable, high performance consumer electronics such as laptops, multimedia devices, cell phones, and other portable electronics.
- Small size with high-current ratings
- Excellent temperature stability
- High reliability and resilience
- Strong arc suppression characteristics
- Lead free materials and RoHS compliant
- Halogen free (refers to: Br/H11349900ppm, Cl/H11349900ppm, Br+Cl/H113491500ppm)
- Monolithic, multilayer design
- High-temperature performance
- -55°C to +125°C operating temperature range
- Laptops
- Digital cameras
- Cell phones Benefits Features
- Printers
- DVD players
- Portable electronics
- Game systems
- LCD monitors
- Scanners Surface-mount Fuses Fast-Acting Chip Fuses
84 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours min. 250% 5 seconds max. 400% 0.05 seconds max. 0402SFF050F/24 0.50 0.380 0.0043 24 35 0402SFF075F/24 0.75 0.210 0.0076 24 35 0402SFF100F/24 1.00 0.120 0.0170 24 35 0402SFF150F/24 1.50 0.056 0.0490 24 35 0402SFF200F/24 2.00 0.035 0.0700 24 35 0402SFF300F/24 3.00 0.021 0.1250 24 35 0402SFF400F/24 4.00 0.014 0.2250 24 35 Part Number 0603SFF050F/32 0.50 0.485 0.0029 32 50 0603SFF075F/32 0.75 0.254 0.0064 32 50 0603SFF100F/32 1.00 0.131 0.0160 32 50 0603SFF150F/32 1.50 0.059 0.0300 32 35 0603SFF200F/32 2.00 0.044 0.0600 32 35 0603SFF250F/32 2.50 0.032 0.1150 32 35 0603SFF300F/32 3.00 0.025 0.1900 32 35 0603SFF350F/32 3.50 0.024 0.2950 32 35 0603SFF400F/32 4.00 0.018 0.4000 32 35 0603SFF500F/32 5.00 0.013 0.7000 32 35 0603SFF600F/24 6.00 0.010 1.1250 24 35 1206SFF050F/63 0.50 0.730 0.0021 63 50 1206SFF075F/63 0.75 0.513 0.0052 63 50 1206SFF100F/63 1.00 0.220 0.0120 63 50 1206SFF150F/63 1.50 0.120 0.0250 63 50 1206SFF175F/63 1.75 0.100 0.0450 63 50 1206SFF200F/63 2.00 0.050 0.0700 63 50 1206SFF250F/32 2.50 0.035 0.1400 32 50 1206SFF300F/32 3.00 0.031 0.2200 32 50 1206SFF400F/32 4.00 0.022 0.3800 32 45 1206SFF500F/32 5.00 0.015 0.6000 32 45 1206SFF600F/32 6.00 0.013 1.0000 32 50 1206SFF700F/32 7.00 0.011 1.7500 32 50 1206SFF800F/32 8.00 0.008 2.5000 32 50 1206SFF600F/24 6.00 0.013 1.0000 24 45 1206SFF700F/24 7.00 0.011 1.7500 24 45 1206SFF800F/24 8.00 0.008 2.5000 24 45 * Measured at/H1134910% of rated current and 25°C ambient temperature. † Melting I2t at 0.001 sec clear time. 0402 (1005mm) Fast-Acting Chip Fuses 0603 (1608mm) Fast-Acting Chip Fuses 1206 (3216mm) Fast-Acting Chip Fuses 0.063 (1. 60) 0.039±0.004 (1 .00±0.10) 0.020±0.004 (0.51±0.10) 0.010±0.004 (0.25±0.10) 0.020±0.004 (0.51±0.10) S Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.028 (0.70) 0.024 (0.60) 0.016 (0.40) Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.031±0.006 (0.80±0.15) 0.031±0.006 (0.80±0.15) 0.014±0.006 (0.36±0.15) 0.063±0.006 (1. 60±0.15) 0.110 (2.80) 0.039 (1 .00) 0.043 (1. 09) 0.024 (0.60) Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.063±0.008 (3.20±0.20) 0.043±0.008 (1. 10±0.20) 0.020±0.010 (0.51±0.25) 0.173 (4.40) 0.071 (1. 80) 0.057 (1. 45) 0.059 (1. 50) Table FF1Clear Time Characteristics for Fast-Acting Chip Fuses Table FF2Typical Electrical Characteristics, Dimensions and Recommended Pad Layout for Fast-Acting Chip Fuses Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† T ypical Electrical CharacteristicsMax. Interrupt Ratings Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† T ypical Electrical CharacteristicsMax. Interrupt Ratings Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† T ypical Electrical CharacteristicsMax. Interrupt Ratings
Surface-mount Fuses– Fast-Acting Chip Fuses RoHS Compliant, ELV Compliant HF Halogen Free 0.1 101 100 Clear-Time (s) 0.1 0.01 0.001 Current (A) 0402SFF AverageTime Current Curves 0.5A 0.75A1.0A1.5A 2.0A 3.0A4.0A 0.001 0.01 0.1 1 10 1000 100 0.1 0.01
0.001 I²t (A²s)
Time (s) 0402SFF I²t vs. t Curves 0.5A 0.75A 1.0A 1.5A 2.0A 3.0A 4.0A Figure FF2Figure FF1 0.1 0.01 0.001 10.1 10 100 Current (A) Clear-Time (s) 0603SFF AverageTime Current Curves 0.5A0.75A1.0A 1.5A2.0A 2.5A3.0A3.5 A 4.0 A 5.0A 6.0A 0.001 0.01 0.1 1 10 10000 1000 100 0.1 0.01 0.001 I²t (A²s) Time (s) 0603SFF I²t vs. t Curves 0.5A 0.75A 1.0A 1.5A 2.0A 2.5A 3.0A 3.5A 4.0A 5.0A 6.0A Figure FF4Figure FF3 Note: Curves are nominal Note: Curves are nominal Figure FF1-FF6Family Performance Curves for Fast-Acting Chip Fuses
86 RoHS Compliant, ELV Compliant HF Halogen Free
0.1 101 100 Clear-Time (s) 0.1 0.01 0.001 Current (A) 1206SFF AverageTime Current Curves 0.5A0.75A1.0A 1.5A1.75 A 2.0A 2.5A3.0A4.0 A 5.0A 6.0A7.0A8.0A I²t (A²s) 10000 1000 100 0.1 0.01 0.001 Time (s) 1206SFF I²t vs. t Curves 0.001 0.01 0.1 1 10 0.5A 0.75A 1.0A 1.5A 1.75A 2.0A 2.5A 3.0A 4.0A 5.0A6.0A 7.0A 8.0A Figure FF6Figure FF5 Note: Curves are nominal /barb4rightPlease go to page 97 for more information for Fast-Acting Chip Fuses. Figure FF1-FF6Family Performance Curves for Fast-Acting Chip Fuses Cont’d
High-Current Rated Chip Fuses The monolithic multilayer design of the TE Circuit Protection high-current-rated chip fuses helps to provide some of the highest current ratings available in the 1206 size and enhances high-temperature performance in a wide range of circuit protection designs. The devices’ small size, high reliability and strong arc suppression characteristics make them suitable for overcurrent protection of power supplies, servers, communications equipment, voltage regulator modules, and other high-current, small size applications.
- Glass ceramic monolithic structure provides stability in application cycling
- High-current rating in a small package allows more efficient use in system space
- Strong arc suppression in overcurrent conditions
- Lead free materials and RoHS compliant
- Halogen free (refers to: Br/H11349900ppm, Cl/H11349900ppm, Br+Cl/H113491500ppm)
- Monolithic multilayer design
- High-temperature performance
- -55°C to +125°C operating temperature range
- Communications equipment
- Voltage regulator modules
- Power supplies
- Servers Benefits Features
High-Current-Rated Chip Fuses
88 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours (min.) 250% 5 seconds (max.) 1206SFH Series 1206SFH100F/24 10 0.010 9 24 100 1206SFH120F/24 12 0.008 14 24 100 1206SFH150F/24 15 0.005 26 24 100 1206SFH200F/24 20 0.003 56 24 100 * Measured at/H1134910% of rated current and 25°C ambient temperature. † Melting I2t at 0.001 sec clear time. Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) 1206 (3216mm) High-Current-Rated Chip Fuses Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.063±0.008 (3.20±0.20) 0.038±0.008 (0.97±0.20) 0.020±0.010 (0.51±0.25) 0.173 (4.40) 0.071 (1. 80) 0.057 (1. 45) 0.059 (1. 50) Nominal I2t (A2sec)† T ypical Electrical Characteristics Max. Interrupt Ratings 10 1000100 ClearTime (s) 0.1 0.01 0.001 Current (A) 1206SFH AverageTime Current Curves 10A12A15A 20A 0.001 0.01 0.1 1 10 10000 1000 100 I²t (A²s) Time (s) 1206SFH I²t vs. t Curves 20A 15A 12A 10A Figure FH2Figure FH1 Note:Curves are nominal Table FH1Clear Time Characteristics for High-Current-Rated Chip Fuses Table FH2Typical Electrical Characteristics, Dimensions and Recommended Pad Layout for High-Current-Rated Chip Fuses Figure FH1-FH2Family Performance Curves for High-Current-Rated Chip Fuses /barb4rightPlease go to page 97 for more information for High-Current-Rated Chip Fuses.
Surface-mount Fuses– Slow-Blow Chip Fuses Available in industry standard 1206 and 0603 chip sizes, TE Circuit Protection’s slow-blow chip fuses help provide overcurrent protection on systems that experience large and frequent current surges as part of their normal operation. The slow-blow chip fuse’s monolithic, multilayer design helps provide some of the highest current ratings available in the 1206 and 0603 footprints and enhances high-temperature performance in a wide range of circuit protection designs. The devices’ small size, high reliability and strong arc suppression characteristics make them suitable for overcurrent protection of power supplies, capacitor filter banks, LCD (Liquid Crystal Display) backlight inverters, electric motors and portable electronics.
- Time-delayed design prevents nuisance openings in pulsed and high inrush current applications
- Small size with high-current ratings
- Strong arc suppression characteristics
- Lead free materials and RoHS compliant
- Halogen free (refers to: Br/H11349900ppm, Cl/H11349900ppm, Br+Cl/H113491500ppm)
- Monolithic multilayer design
- High-temperature performance
- -55°C to +125°C operating temperature range
- Small motors systems
- Portable electronics
- Input power ports Benefits Features
- Power over Ethernet (POE)
- Test equipment
- POL converter protection
- Computer drives
- Displays
- Printers Surface-mount Fuses Slow-Blow Chip Fuses
90 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours (min.) 200% 1 second (min.) 120 seconds (max.) 300% 0.1 second (min.) 3 seconds (max.) % of rated current Clear time at 25°C 100% 4 hours (min.) 200% 1 second (min.) 120 seconds (max.) 300% 0.1 second (min.) 3 seconds (max.) 0603SFS Series 1206SFS Series 1206SFS100F/63 1.0 0.360 0.11 63 50 1206SFS125F/63 1.25 0.200 0.22 63 50 1206SFS150F/63 1.5 0.150 0.23 63 50 1206SFS200F/63 2.0 0.088 0.63 63 50 1206SFS250F/32 2.5 0.065 0.90 32 50 1206SFS300F/32 3.0 0.034 1.20 32 50 1206SFS350F/32 3.5 0.028 1.60 32 50 1206SFS400F/32 4.0 0.024 2.20 32 50 1206SFS450F/32 4.5 0.020 3.60 32 50 1206SFS500F/32 5.0 0.016 5.30 32 50 1206SFS550F/24 5.5 0.014 6.40 24 50 1206SFS600F/24 6.0 0.011 8.50 24 60 1206SFS700F/24 7.0 0.010 10.00 24 60 1206SFS800F/24 8.0 0.009 16.90 24 60 * Measured at/H1134910% of rated current and 25°C ambient temperature. † Melting I2t at 0.001 sec clear time. Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) 1206 (3216mm) Slow-Blow Chip Fuses 0603 (1608mm) Slow-Blow Chip Fuses Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.063±0.008 (3.20±0.20) 0.038±0.008 (0.97±0.20) 0.020±0.010 (0.51±0.25) 0.173 (4.40) 0.071 (1. 80) 0.057 (1. 45) 0.059 (1. 50) Nominal I2t (A2sec)† 0603SFS100F/32 1.0 0.200 0.093 32 50 0603SFS150F/32 1.5 0.100 0.18 32 50 0603SFS200F/32 2.0 0.052 0.32 32 50 0603SFS250F/32 2.5 0.041 0.63 32 50 0603SFS300F/32 3.0 0.031 0.87 32 50 0603SFS350F/32 3.5 0.021 1.20 32 50 0603SFS400F/32 4.0 0.017 2.30 32 50 0603SFS450F/32 4.5 0.015 2.70 32 50 0603SFS500F/32 5.0 0.013 3.20 32 50 Part Number Rated Current (A) Nominal Cold DCR (Ω)* Voltage (VDC ) Current (A) Nominal I2t (A2sec)† Shape and Dimensions Inch (mm) Recommended Pad Layout Inch (mm) 0.031±0.006 (0.80±0.15) 0.031±0.006 (0.80±0.15) 0.014±0.006 (0.36±0.15) 0.063±0.006 (1. 60±0.15) 0.110 (2.80) 0.039 (1 .00) 0.043 (1. 09) 0.024 (0.60) T ypical Electrical Characteristics Max. Interrupt Ratings T ypical Electrical Characteristics Max. Interrupt Ratings Table FS1Clear Time Characteristics for Slow-Blow Chip Fuses Table FS2Typical Electrical Characteristics, Dimensions and Recommended Pad Layout for Slow-Blow Chip Fuses
Surface-mount Fuses– Slow-Blow Chip Fuses RoHS Compliant, ELV Compliant HF Halogen Free ClearTime (s) 100 0.1 0.01 0.001 10 1001 Current (A) 0603SFS AverageTime Current Curves 1.0A 1.5A 2.0A 2.5 A 3.0 A 3.5 A 4.0A4.5A5.0A Figure FS1 I2t (A2s) 10,000 1000 100 0.1 0.01 0.001 0.01 100.1 1 100 Time (s) 0603SFS I²t vs. t Curves 1.0A 1.5A 2.0A 2.5A 3.0A 3.5A 4.0A 4.5A 5.0A Figure FS2 Note:Curves are nominal Figure FS1-FS4Family Performance Curves for Slow-Blow Chip Fuses
92 RoHS Compliant, ELV Compliant HF Halogen Free
ClearTime (s) 100 0.1 0.01 0.001 10 100 10001 Current (A) 1206SFS AverageTime Current Curves 1.0A 1.25A1.5A 2.0A 2.5A3.0A3.5 A 4.0 A 4.5A 5.0A 5.5A6.0A7.0A8.0A Figure FS3 I2t (A2s) 100000 10000 1000 100 0.1 0.01 0.001 0.01 100.1 1 100 Time (s) 1206SFS I²t vs. t Curves 1.0A 1.5A 2.5A 3.0A 3.5A 4.0A 4.5A 5.0A 5.5A 6.0A 7.0A 8.0A 2.0A 1.25A Figure FS4 Note:Curves are nominal Figure FS1-FS4Family Performance Curves for Slow-Blow Chip Fuses Cont’d /barb4rightPlease go to page 97 for more information for Slow-Blow Chip Fuses.
Surface-mount Fuses– 2410 Very Fast-Acting Fuses The 2410(6125) is Wire-in Air SMD Fuse which is very suitable for secondary level overcurrent protection applications. These lead-free surface mount devices offer more reliability and have no end cap falling off risk. Straight wire element in air performs consistent fusing and cutting characteristics.
- Very fast acting at 200% overload current level
- Excellent inrush current withstanding capability
- High reliability and resilience
- Strong arc suppression characteristics
- Copper terminal with nickel and tin plated
- Halogen free, RoHS compliant and 100% lead-free
- Copper or copper alloy composite fuse link
- Fiberglass enforced epoxy fuse body
- Wide range of current rating
- -55°C to +125°C operating temperature range (with de-rating)
- Industrial equipment
- LCD/PDP TV
- Backlight inverter Benefits Features
- Power supplier
- Telecom system
- Networking
- Game systems
- White goods
- Automotive Surface-mount Fuses
2410 Very Fast-Acting Fuses
NENENENENENENENENENENENEWWWWWWWWWWWWNEW
94 RoHS Compliant, ELV Compliant HF Halogen Free
% of rated current Clear time at 25°C 100% 4 hours (min.) 2410 (6125 mm) Very Fast-Acting Fuse Shape and Dimensions mm (Inch) D A C B Table SFV1Clear Time Characteristics for 2410 Very Fast-Acting Fuses Table SFV2Typical Electrical Characteristics, Dimensions and Recommended Pad Layout for T ypical Electrical Characteristics Max. Interrupt Ratings Marking Code Rated Current (A) Nominal Cold DCR (Ω)* Nominal I2t (A 2sec) Voltage Current (A)(V AC ) (V DC ) 2410SFV0.50FM/125-2 C 0.5 0.2310 0.10 250 125 50A @ 250V AC 50A @ 125V DC 300A @ 32V DC 2410SFV0.63FM/125-2 S 0.6 0.1740 0.16 250 125 2410SFV0.75FM/125-2 D 0.8 0.1480 0.23 250 125 2410SFV1.00FM/125-2 E 1.0 0.0930 0.59 250 125 2410SFV1.25FM/125-2 F 1.3 0.0700 0.96 250 125 2410SFV1.50FM/125-2 G 1.5 0.0620 1.19 125 125 50A @ 125V AC 50A @ 125V DC 300A @ 32V DC 2410SFV2.00FM/125-2 I 2.0 0.0420 2.75 125 125 2410SFV2.50FM/125-2 J 2.5 0.0310 1.21 125 125 2410SFV3.00FM/125-2 K 3.0 0.0249 1.73 125 125 2410SFV3.15FM/125-2 V 3.2 0.0232 2.20 125 125 2410SFV3.50FM/125-2 L 3.5 0.0220 2.50 125 125 2410SFV4.00FM/125-2 M 4.0 0.0172 4.10 125 125 2410SFV5.00FM/125-2 N 5.0 0.0143 5.90 125 125 2410SFV6.30FM/125-2 O 6.3 0.0100 12.50 125 125 2410SFV7.00FM/125-2 P 7.0 0.0094 14.20 125 125 2410SFV8.00FM/125-2 R 8.0 0.0086 20.30 125 125 2410SFV10.0FM/125-2 Q 10.0 0.0066 29.20 125 125 35A @ 125V AC 50A @ 125V DC 300A @ 32V DC 2410SFV12.0FM/065-2 X 12.0 0.0053 49.20 65 65 50A @ 65V AC 50A @ 65V DC 300A @ 32V DC2410SFV15.0FM/065-2 Y 15.0 0.0038 102.50 65 65 2410SFV20.0FM/065-2 Z 20.0 0.0034 126.20 65 65 50A @ 65V AC 50A @ 65V DC 300A @ 32V DC * Measured at/H1134910% of rated current and 25°C ambient temperature. Recommended Pad Layout mm (Inch) 6.86 (0.270) 3.15 (0.124) 1 .96 (0.077) 2.95 (0.116) A BCD Min Max Min Max Min Max Min Max
Surface-mount Fuses– 2410 Very Fast-Acting Fuses RoHS Compliant, ELV Compliant HF Halogen Free /barb4rightPlease go to page 97 for more information for 2410 Fast-Acting Fuses. ClearTime (s) 100 0.1 0.01 0.001 10 100010010.1 Current (A) 2410SFV AverageTime Current Curves Figure SFV1 I2t (A2s) 100,000 10,000 1000 100 0.1 0.01 0.010.001 100.1 1 100 Time (s) 2410SFV I2T vs. t Curves 1.00A 0.50A 0.63A 0.75A 1.50A 1.25A 2.00A 2.50A 3.00A 3.15A 3.50A 4.00A 5.00A 7.00A 8.00A 10.0A 12.0A 15.0A 20.0A 6.30A Figure SFV2 Figure SFV1-SFV2Family Performance Curves for 2410 Very Fast-Acting Fuses Note:Curves are nominal
Surface-mount Fuses- Specifications for All Fuses RoHS Compliant, ELV Compliant HF Halogen Free Specifications, Packaging Information, Agency Approvals and Part Numbering Systems for All Fuses Operating temperature -55°C to +125°C Mechanical vibration Withstands 5-3000 Hz at 30 Gs when evaluated per Method 204 of MIL-STD-202 Mechanical shock Withstands 1500 Gs, 0.5 millisecond half-sine pulses when evaluated per Method 213 of MIL-STD-202 Thermal shock Withstands 100 cycles from -65°C to +125°C when evaluated per Method 107 of MIL-STD-202 Resistance to soldering heat Withstands 60 seconds at +260°C when evaluated per Method 210 of MIL-STD-202 Solderability Meets 95% minimum coverage requirement when evaluated per Method 208 of MIL-STD-202 Moisture resistance Withstands 10 cycles when evaluated per Method 106 of MIL-STD-202 Salt spray Withstands 48-hour exposure when evaluated per Method 101 of MIL-STD-202 Storage temperature /H1134930°C/ 85% RH Storage humidity Per MIL-STD-202F , Method 106F Construction body material Ceramic (1206/0603/0402); Fiberglass/Epoxy (2410) Termination material Silver, Nickel, Tin Fuse element Silver(1206/0603/0402); Copper/Copper Alloy (2410) 1206/0603/0402 Series T emperature Effect on Current Rating T emperature Effect on Current Rating % De-rating % De-rating 105 100 110 105 100 Maximum Operating T emperature (˚C) Maximum Operating T emperature (˚C) -55 -35 -15 5 25 45 65 85 105 125 145 -55 -35 -15 5 25 45 65 85 105 125 Insulation resistance after opening20,000Ω minimum @ rated voltage. Fuse clearing under low voltage conditions may result in lower - post-clearing insulation values. Under normal fault conditions TE Circuit Protection fuses provide sufficient insulation resistance for circuit protection. Current carrying capacity Withstands 100% rated current at +25°C ambient for 4 hours when evaluated per MIL-PRF-23419. Table F1Environmental Specifications for All Fuses Table F2Material Specifications for All Fuses Figure F1Thermal Derating Current for All Fuses Table F3Electrical Specifications for All Fuses
98 RoHS Compliant, ELV Compliant HF Halogen Free
Recommended conditions for hand soldering: 1. Using hot air rework station that can reflow the solder on both terminations at the same time is strongly recommended, do not directly contact the chip termination with the tip of soldering iron. 2. Preheating: 150°C, 60s (min). Appropriate temperature (max) of soldering iron tip/soldering time (max): 280°C /10s or 350°C / 3s. 0402(1005) 10,000 178mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to 10 0603(1608) 4,000 178mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to 10 0603SFV(1608) 6,000 178mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Paper 5 1 to 10 1206(3216) 3,000 178mm white plastic 9.0 ± 0.5mm 8.00 ± 0.10mm Plastic 5 1 to 10 2410(6125) 2,000 178mm white plastic 13.4 ± 0.5mm 12.00 ± 0.10mm Plastic 4 1 to 10 Size Reel Quantity (pcs) Reel Diameter Reel Width Carrier T ape Size T apeT ype Reels per Outside Shipment Box Outside Shipment Boxes per Overpack Table F4Packaging Information for All Fuses Figure F2Recommended Soldering Temperature Profile for All Fuses Profile Feature 1206/0603/0402 2410 Average ramp up rate (TsMAX toTp) 3°C/second max. 3°C/second max. Preheat
- Temperature min. (TsMIN ) 150°C 150°C
- Temperature max. (TsMAX ) 200°C 200°C
- Time (tsMIN to tsMAX ) 60-180 seconds 40-100 seconds Time maintained above:
- Temperature (T L) 217°C 200°C
- Time (tL) 60-150 seconds 30-90 seconds Peak/Classification temperature (Tp) 260°C max. 250°C max. Time within 5°C of actual peak temperature Time (tp) 20-40 seconds 30-40 seconds From 25°C to preheating (150°C) 8 minutes max. 40-100 seconds Ramp down rate 4°C/second max. Natural cooling Critical Zone TL to TpRamp up t 25˚C to Peak Reflow Profile Time Ramp down ts Preheat TsMAX TL Tp tp TsMIN tL Te mperature Classification Reflow Profiles
Surface-mount Fuses- Specifications for All Fuses RoHS Compliant, ELV Compliant HF Halogen Free 11P0 P0 P2 F F W W t Paper CarrierT ape Specifications Plastic CarrierT ape Specifications Table F5Tape and Reel Specifications for All Fuses Figure F3Component Tape Dimensions for All Fuses Dimension in inches (mm) Mark 0402 (1005) 0603 (1608) 1206 (3216) 0603SFV (1608) 2410 (6125) D 1 —— 0.039 max — 0.61 ± 0.004
100 RoHS Compliant, ELV Compliant HF Halogen Free
Description Mark 1206/0603/0402 2410 Hub outer diameter B 60 60.2 Reel inside width W 1 9 13.4 Reel outside width W 2 11.4 16 Tape width 8 B Figure F4Reel Dimensions for All Fuses Agency Approvals for All Fuses UL File # E197536 Part Numbering System for Fast-Acting, Slow-Blow And 0603 Very Fast-Acting Chip Fuses
1206 SF F 400 F / 24 -2
-2 = Tape and Reel Voltage Rating 24 = 24V DC Special Code F = RoHS Compliant FM = RoHS Compliant + Marked Part Rated Current 050 = 0.50 Amps 400 = 4 Amps Fuse BlowT ype F = Fast Acting S = Slow Blow SF = Surface Mount Fuse Size (1206, 0603, 0402) Part Numbering System for High-Current-Rated Chip Fuses
1206 SF H 100 F / 24 -2
-2 = Tape and Reel Voltage Rating 24 = 24V DC Special Code F = RoHS Compliant FM = RoHS Compliant + Marked Part Rated Current 100 = 10 Amps Fuse BlowT ype H = High Current SF = Surface Mount Fuse Size (1206) Dimension (mm)
Surface-mount Fuses- Specifications for All Fuses RoHS Compliant, ELV Compliant HF Halogen Free Part Numbering System for 2410 Very Fast-Acting Fuses 2410 SF V 6.30 FM / 125 -2 Packaging -2 = Tape and Reel Voltage Rating 125 = 125VDC Special Code F = RoHS Compliant M = Marked Part Rated Current 6.30= 6.30 Amps Fuse BlowT ype V = Very Fast Acting SF = Surface Mount Fuse Size (0.24*0.10 inch) Warning : All information, including illustrations, is believed to be accurate and reliable. Users, however, should independently evaluate the suitability of and test each product selected for their application. Tyco Electronics Corporation and/or its Affiliates in the TE Connectivity Ltd. family of companies (“TE”) makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use.TE’s only obligations are those in the TE Standard Terms and Conditions of Sale for this product, and in no case will TE be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Specifications are subject to change without notice. In addition,TE reserves the right to make changes to materials or processing that do not affect compliance with any applicable specification without notification to Buyer.