1.5KE6.8 TSC
Document overview
- Manufacturer or author: Provided By digicamel.com
- PDF pages: 3
Technical content
Features
UL Recognized File # E-96005 Plastic package has Underwriters Laboratory Flammability Classification 94V-0 Exceeds environmental standards of MIL-STD-19500 1500W surgec apability at 10 x 100 us waveform, duty cycle: 0.01% Excellent clamping capability Low zener impedance Fast response time: Typically less than 1.0ps from 0 volts to VBR for unidirectional and 5.0 ns for bidirectional Typical IR less than 1uA above 10V High temperature soldering guaranteed: 260°C / 10 seconds / .375”,(9.5mm) lead length / 5lbs.,(2.3kg) tension Mechanical Data Case: Molded plastic Lead: Axial leads, solderable per MIL-STD-202, Lead: Method 208 Polarity: Color band denotes cathode except bipolar Weight: 0.94gram DO-201 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol Value Units Peak Power Dissipation atTA=25 O C, Tp=1ms (Note 1) PPK Minimum1500 Watts Steady State Power Dissipation at TL=75 °C Lead Lengths .375”, 9.5mm (Note 2) PD 5.0 Watts Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method) (Note 3) IFSM 200 Amps Maximum Instantaneous Forward Voltage at 50.0A for Unidirectional Only (Note 4) VF 3.5 / 5.0 Volts Operating and Storage Temperature Range TJ,T STG - 5 5t o+1 7 5 ° C Notes: 1. Non-repetitive Current Pulse Per Fig. 3 and Derated above TA=25OC Per Fig. 2. Notes: 3. 8.3ms Single Half Sine-wave or Equivalent Square Wave, Duty Cycle=4 Pulses Per Minutes Notes: 3.Maximum. Devices for Bipolar Applications Notes: 2. Electrical Characteristics Apply in Both Directions.
- 577 - RATINGS AND CHARACTERISTIC CURVES (1.5KE SERIES) FIG.2- PULSE DERATING CURVE PEAK PULSE POWER (Ppp) or CURRENT DERATING IN PERCENT AGE, % IPPM 0 25 50 75 100 125 150 175 200 100 T AMBIENT TEMPERATURE, CA, o FIG.6- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL ONLY l , PEAK FOR WARD SURGE CURRENT AMPERES FSM 1 10 10010 200 100 NUMBER OF CYCLES AT 60Hz 8.3ms Single Half Sine Wave JEDEC Method Tj=Tj max. FIG.1- PEAK PULSE POWER RATING CURVE P , PEAK PULSE POWER, KW PPM 0.1/c109s /c49/c48/c48/c109s /c49/c46/c48ms /c49/c48ms/c49/c48/c109s/c49/c109s0.1 100 1.0 tp, PULSE WIDTH, sec. NON-REPETITIVE PULSE WAVEFORM SHOWN in FIG.3 T =25 C A 0 FIG.3- PULSE WAVEFORM PEAK PULSE CURRENT 0 0 1.0 2.0 3.0 4.0 100 150 t, TIME, ms PULSE WIDTH (td) is DEFINED as the POINT WHERE the PEAK CURRENT DECAYS to 50% of l PPM td tr=10 sec./c109 10/1000 sec. WAVEFORM as DEFINED by R.E.A. PEAK VALUE lPPM HALF VALUE- lPPM TL, LEAD TEMPERATURE, C o FIG.4- STEADY STATE POWER DERATING CURVE PM , STEADY STATE POWER DISSIP ATION, WATTS (AV) 0 25 50 75 100 125 150 175 200 2.5 5.0 60Hz RESISTIVE OR INDUCTIVE LOAD 1.6 X 1.6 X .040" ( 4 0X4 0X1 m m . ) COPPER HEAT SINKS L=0.375"(9.5mm) LEAD LENGTHS FIG.5- TYPICAL JUNCTION CAPACITANCE UNIDIRECTIONAL C , JUNCTION CAP ACITANCE.(pF) J 1.0 10 100 200 100 1,000 10,000 V , BREAKDOWN VOLTAGE. VOLTS(BR) Tj=25 C f=1.0MHz Vsig=50mVp-p UNIDIRECTIONAL BIDIRECTIONAL V -RATED STAND-OFF VOLTAGE R V= 0R
- 578 - ELECTRICAL CHARACTERISTICS (TA=25OC unless otherwise noted) Stand-Off Maximum Maximum Maximum Maximum JEDEC GENERAL Nominal Test Current Volta ge Reverse Leaka ge Peak Sur ge Clampin g Temperature TYPE PART Volta ge @IT(mA) VWM at Vwm Current IPPM Volta ge at IPPM Coefficient NUMBER NUMBER (Volts) Min Max (Volts) ID (uA) (Note 2)(Amps) VC(Volts) of VBR(% / OC) Breakdown Voltage VBR (Volts) (Note 1) Notes: 1. VBR measured after IT applied for 300us, IT =square wave pulse or equivalent. 2. Surge current waveform per Figure 3 and derate per Figure 2. 3. For bipolar types having VWM of 10 volts and under, the ID limit is doubled. 4. All terms and symbols are consistent with ANSI/IEEE C62.35.