06031A151JAT2A

DATASHEET SEARCH SITE

Document overview

• Manufacturer or author: Provided By digicamel.com
• PDF pages: 4

Technical content

Typical Capacitance Change Envelope: 0 ± 30 ppm/°C % /H9004 Capacitance +0.5 -0.5 -55 -35 -15 +5 +25 +45 +65 +85 +105 +125 Temperature °C Temperature Coefficient Insulation Resistance (Ohm-Farads) 1,000 10,000 100 0 20 40 60 80 Temperature °C Insulation Resistance vs Temperature 100 Impedance, /H9024 10 100 1000 Frequency, MHz Variation of Impedance with Chip Size Impedance vs. Frequency 1000 pF - C0G (NP0) 1.0 0.1 1206 0805 1812 1210 Impedance, /H9024 10 100 1000 Frequency, MHz Variation of Impedance with Ceramic Formulation Impedance vs. Frequency 1000 pF - C0G (NP0) vs X7R 0805 0.10 0.01 1.00 X7R NPO 10.00 % /H9004 Capacitance 1KHz 10 KHz 100 KHz 1 MHz 10 MHz Frequency /H9004 Capacitance vs. Frequency Impedance, /H90241,000 10,000 100 1 10 100 1000 Frequency, MHz Variation of Impedance with Cap Value Impedance vs. Frequency 0805 - C0G (NP0) 10 pF vs. 100 pF vs. 1000 pF 10 pF 100 pF 1000 pF 1.0 0.1 10.0 100,000 C0G (NP0) Dielectric General Specifications C0G (NP0) is the most popular formulation of the “temperature-compensating,” EIA Class I ceramic materials. Modern C0G (NP0) formulations contain neodymium, samarium and other rare earth oxides. C0G (NP0) ceramics offer one of the most stable capacitor dielectrics available. Capacitance change with temperature is 0 ±30ppm/°C which is less than ±0.3% /H9004C from -55°C to +125°C. Capacitance drift or hysteresis for C0G (NP0) ceramics is negligible at less than ±0.05% versus up to ±2% for films. Typical capacitance change with life is less than ±0.1% for C0G (NP0), one-fifth that shown by most other dielectrics. C0G (NP0) formulations show no aging characteristics. 0805 Size (L" x W") Voltage 6.3V = 6 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 500V = 7 A Dielectric C0G (NP0) = A 101 Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros J Capacitance Tolerance B = ±.10 pF (<10pF) C = ±.25 pF (<10pF) D = ±.50 pF (<10pF) F = ±1% (≥ 10 pF) G = ±2% (≥ 10 pF) J = ±5% K = ±10% A Failure Rate A = Not Applicable T Terminations T = Plated Ni and Sn 7 = Gold Plated Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk Contact Factory For Multiples A Special Code A = Std. Product PART NUMBER (see page 2 for complete part number explanation) Contact Factory For 1 = Pd/Ag Term NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values.

C0G (NP0) Dielectric Specifications and Test Methods Parameter/Test NP0 Specification Limits Measuring Conditions Operating Temperature Range -55ºC to +125ºC Temperature Cycle Chamber Capacitance Within specified tolerance Freq.: 1.0 MHz ± 10% for cap ≤ 1000 pF Q <30 pF: Q≥ 400+20 x Cap Value 1.0 kHz ± 10% for cap > 1000 pF ≥30 pF: Q≥ 1000 Voltage: 1.0Vrms ± .2V Insulation Resistance 100,000MΩ or 1000MΩ - μF, Charge device with rated voltage for whichever is less 60 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Note: Charge device with 150% of rated voltage for 500V devices. Appearance No defects Deflection: 2mm Capacitance Test Time: 30 seconds Resistance to Variation ±5% or ±.5 pF, whichever is greater Flexure Q Meets Initial Values (As Above)Stresses Insulation ≥ Initial Value x 0.3Resistance Solderability ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC with fresh solder for 5.0 ± 0.5 seconds Appearance No defects, <25% leaching of either end terminal Capacitance Variation ≤ ±2.5% or ±.25 pF, whichever is greater Dip device in eutectic solder at 260ºC for 60 Q Meets Initial Values (As Above) seconds. Store at room temperature for 24 ± 2Resistance to hours before measuring electrical properties.Solder Heat Insulation Meets Initial Values (As Above)Resistance Dielectric Meets Initial Values (As Above)Strength Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes Capacitance Variation ≤ ±2.5% or ±.25 pF, whichever is greater Step 2: Room Temp ≤ 3 minutes Q Meets Initial Values (As Above) Step 3: +125ºC ± 2º 30 ± 3 minutesThermal Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutesResistance Dielectric Meets Initial Values (As Above) Repeat for 5 cycles and measure after Strength 24 hours at room temperature Appearance No visual defects Capacitance Variation ≤ ±3.0% or ± .3 pF, whichever is greater Charge device with twice rated voltage in ≥ 30 pF: Q≥ 350 test chamber set at 125ºC ± 2ºC Load Life Q ≥10 pF, <30 pF: Q≥ 275 +5C/2 for 1000 hours (+48, -0).(C=Nominal Cap) <10 pF: Q≥ 200 +10C Insulation ≥ Initial Value x 0.3 (See Above) Remove from test chamber and stabilize at Resistance room temperature for 24 hours Dielectric Meets Initial Values (As Above) before measuring. Strength Appearance No visual defects Capacitance Variation ≤ ±5.0% or ± .5 pF, whichever is greater Store in a test chamber set at 85ºC ± 2ºC/ ≥ 30 pF: Q≥ 350 85% ± 5% relative humidity for 1000 hours Load Q ≥10 pF, <30 pF: Q≥ 275 +5C/2 (+48, -0) with rated voltage applied. Humidity <10 pF: Q≥ 200 +10C Insulation ≥ Initial Value x 0.3 (See Above) Remove from chamber and stabilize at Resistance room temperature for 24 ± 2 hours Dielectric Meets Initial Values (As Above) before measuring. Strength 1mm/sec 90 mm

C0G (NP0) Dielectric Capacitance Range Letter ABCEGJ K M N PQXYZ PAPER EMBOSSED SIZE 01005 0201 0402 0603 0805 1206 Soldering Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow/Wave Packaging All Paper All Paper All Paper All Paper Paper/Embossed Paper/Embossed WVDC 16 25 50 16 25 50 16 25 50 100 16 25 50 100 200 16 25 50 100 200 500 Cap 0.5 A C C C G G G G J J J J J J J J J J J (pF) 1.0 B A C C C G G G G J J J J J J J J J J J

1.2 B A C C C G G G G J J J J J J J J J J J

1.5 B A A C C C G G G G J J J J J J J J J J J

1.8 B A A C C C G G G G J J J J J J J J J J J

2.2 B A A C C C G G G G J J J J J J J J J J J

2.7 B A A C C C G G G G J J J J J J J J J J J

3.3 B A A C C C G G G G J J J J J J J J J J J

3.9 B A A C C C G G G G J J J J J J J J J J J

4.7 B A A C C C G G G G J J J J J J J J J J J

5.6 B A A C C C G G G G J J J J J J J J J J J

6.8 B A A C C C G G G G J J J J J J J J J J J

8.2 B A A C C C G G G G J J J J J J J J J J J

1 0 B AACCCGGGGJ J JJ JJ JJ J J J 1 2 B AACCCGGGGJ J JJ JJ JJ J J J 1 5 B AACCCGGGGJ J JJ JJ JJ J J J 1 8 B AACCCGGGGJ J JJ JJ JJ J J J 2 2 B AACCCGGGGJ J JJ JJ JJ J J J 2 7 AACCCGGGGJ J JJ JJ JJ J J J 3 3 AACCCGGGGJ J JJ JJ JJ J J J 3 9 A CCCGGGGJ J JJ JJ JJ J J J 4 7 A CCCGGGGJ J JJ JJ JJ J J J 5 6 A CCCGGGGJ J JJ JJ JJ J J J 6 8 A CCCGGGGJ J JJ JJ JJ J J J 8 2 A CCCGGGGJ J JJ JJ JJ J J J

100 A C C C G G G G J J J J J J J J J J J

120 C C C G G G G J J J J J J J J J J J

150 C C C G G G G J J J J J J J J J J J

180 C C C G G G G J J J J J J J J J J J

220 C C C G G G G J J J J J J J J J J M

270 C C C G G G G J J J J M J J J J J M

330 C C C G G G G J J J J M J J J J J M

390 C C C G G G J J J J M J J J J J M

470 C C C G G G J J J J M J J J J J M

560 G G G J J J J M J J J J J M

680 G G G J J J J J J J J J P

820 G G G J J J J J J J J M

1000 G G G J J J J J J J J Q

1200 JJ J J J JJQ

1500 JJ J J J J MQ

1800 JJ J J J M M

2200 JJN J J M P

2700 JJN J J M P

3300 JJ J J M P

3900 JJ J J M P

4700 JJ J J M P

5600 JJ M

Cap 0.010 MM (µF) 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.068 0.082 0.1 WVDC 25 50 16 25 50 16 25 50 100 16 25 50 100 200 16 25 50 100 200 500 SIZE 01005 0201 0402 0603 0805 1206 L/H17010 /H17010 /H17010 /H17010 W /H17010/H17010 /H17010 /H17010 T t PREFERRED SIZES ARE SHADED

C0G (NP0) Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 1210 1812 1825 2220 2225 Soldering Reflow Only Reflow Only Reflow Only Reflow Only Reflow Only Packaging Paper/Embossed All Embossed All Embossed All Embossed All Embossed WVDC 25 50 100 200 500 25 50 100 200 500 50 100 200 50 100 200 50 100 200 Cap 0.5 (pF) 1.0 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 J 12 J 15 J 18 J 22 J 27 J 33 J 39 J 47 J 56 J 68 J 82 J 100 J 120 J 150 J 180 J 220 J 270 J 330 J 390 M 470 M

560 J J J J M

680 J J J J M

820 J J J J M

1000 J J J J M K K K K M M M M M M P

1200 J J J M M K K K K M M M M M M P

1500 J J J M M K K K K M M M M M M P

1800 J J J M K K K K M M M M M M P

2200 J J J Q K K K K P M M M M M P

2700 J J J Q K K K P Q M M M M M P

3300 J J J K K K P Q M M M X M M P

3900 J J M K K K P Q M M M X M M P

4700 J J M K K K P Q M M M X X X M M P

5600 J J K K M P X M M M X X X M M P

6800 J J K K M X M M M X X X M M P

8200 J J K M M M M X X X M M P

Cap 0.010 J J K M M M M X X X M M P (μF) 0.012 J J K M M M X X X M M P

0.015 M M M M X X X M M Y

0.018 M M P M X X X M M Y

0.022 M M P X X M Y Y

0.027 M M P X X P Y Y

0.033 M M P X X P

0.039 M M P Y P

0.047 M M P Y P

0.068 M M P

0.082 M M Q

0.1 Q WVDC 25 50 100 200 500 25 50 100 200 500 50 100 200 50 100 200 50 100 200 SIZE 1210 1812 1825 2220 2225 L/H17010 /H17010 /H17010 /H17010 W /H17010/H17010 /H17010 /H17010 T t Letter ACEGJK M NP QXYZ PAPER EMBOSSED